Axel AX3000 60E Manuel utilisateur
AX3000 Platine Terminal
Ethernet TCP/IP
Model 60E
Installation Guide
September 2002 - Ref: I60EE0210-1
Model AX3000/M60E
The reproduction of this material, in part or whole, is strictly prohibited. For
additional information, please contact:
14 Avenue du Québec
Bât. K2 EVOLIC - BP 728
91962 Courtabœuf cedex - FRANCE
Tel.: 33 1.69.28.27.27
Fax: 33 1.69.28.82.04
The information in this document is subject to change without notice. AXEL
assumes no responsibility for any errors that may appear in this document.
All trademarks and registered trademarks are the property of their respective
holders.
© - 2002 - AXEL - All Rights Reserved.
1 - SAFETY NOTICES.......................................................................................1
2 - INSTALLATION ...........................................................................................2
2.1 - DESCRIPTION.......................................................................................2
2.2 - INSTALLATION......................................................................................2
2.2.1 - Monitor and keyboard......................................................................3
2.2.2 - Ethernet Connection........................................................................4
2.2.3 - Auxiliary Ports..................................................................................5
2.2.4 - AC Power Connection .....................................................................5
2.2.5 - Power On.........................................................................................6
3 - SETTING-UP THE AX3000..........................................................................7
3.1 - QUICK SET-UP......................................................................................7
3.2 - INTERACTIVE SET-UP .........................................................................8
3.3 - SETTING-UP THE RDP SERVER.......................................................10
4 - CONNECTOR PIN ASSIGNMENTS ..........................................................11
4.1 - ETHERNET PORT RJ45 (10BT) .........................................................11
4.2 - SERIAL PORTS AUX1 AND AUX2 (RJ45) .........................................12
4.2.1 - RJ45-DB9 and RJ45-DB25 adaptors ............................................13
4.2.2 - Peripheral RJ45 cables .................................................................13
4.3 - KEYBOARD INTERFACE....................................................................14
4.4 - MOUSE INTERFACE...........................................................................14
4.5 - VIDEO INTERFACE.............................................................................15
4.6 - PARALLEL INTERFACE .....................................................................16
5 - PROBLEM SOLVING.................................................................................17
The AXEL AX3000 Terminal is based on a modular concept.
VGA / SVGA
standard monitor
standard keyboard
AX3000
The AX3000 is totally designed and manufactured by Axel. The terminal's
electronics is contained within a slim base unit which provides connections
for a VGA or SVGA monitor, keyboard, system printer, serial devices and
Ethernet network.
Safety Notices
Installation Guide - Model 60E 1
1 - SAFETY NOTICES
yCheck AC voltage from the wall outlet is inside 220-240 Volts range.
yThe wall outlet used must be reached easily and as nearest as possible to the
AX3000 Terminal to connect or disconnect the power cord.
yMake sure to power off all devices before connecting or disconnecting any
one of them (monitor VGA cable, keyboard and serial or parallel cables).
yIn order to ensure compliance with European EMC regulations (EN 55022), it
is required that shielded cables be used when interfacing with other devices
(peripherals or computers).
yTo install and connect the keyboard and the monitor, refer to the respective
supplier installation manuals.
Installation
2 Installation Guide - Model 60E
2 - INSTALLATION
This chapter provides information and instructions to install the AX3000 Model
60E.
2.1 - DESCRIPTION
A green LED, located on the face plate, indicates when the AX3000 is powered
on.
The AX3000 has the following connectors and switches on the rear panel:
- power switch,
- connector for the external power transformer cord,
- connector for a VGA or SVGA monitor (colour or monochrome),
- PS/2 keyboard connector,
- PS/2 mouse connector,
- auxiliary serial ports: RJ45 (AUX1 and AUX2),
- auxiliary parallel port: female 25-pin (PARALLEL),
- TCP/IP port: RJ45 (10BT).
IO
SVGA PARALLELAUX2 10BTAUX1KEYB
12VAC
External Power Connector Keyboard Port
VGA Monitor
Ethernet Port
Low Voltage Connectors
Parallel Port
Power Switch Mouse Port
Serial Ports
2.2 - INSTALLATION
For safety reasons and to prevent component damage, do not apply power to
the AX3000 before connecting or disconnecting any cable. Do not plug in the
AX3000 power cord until all other connectors have been plugged in.
Installation
Installation Guide - Model 60E 3
Make sure the AX3000 and monitor power switches are in the OFF (0) position
before connecting cables to the back panel.
1 : On
0 : Off
2.2.1 - Monitor and keyboard
Plug in the VGA monitor cable, the AT-compatible keyboard cable and the
optional mouse cable to the dedicated connectors on the terminal back panel:
IO
SVGA PARALLELAUX2 10BTAUX1KEYB
12VAC
If your keyboard is fitted with a DIN connector, connect it using a DIN-to-Mini-
DIN adaptor.
To comply with EMC regulations, the VGA signal cable must be shielded.
Installation
4 Installation Guide - Model 60E
Note: when the terminal is installed in a cabinet or rack, it is essential to
maintain air circulation around the VGA/SVGA monitor.
2.2.2 - Ethernet Connection
Plug the 10Base-T ethernet cable into the socket labelled 10BT on the back of
the AX3000 (see chapter 4.1 for technical specifications and pin assignments).
IO
SVGA PARALLELAUX2 10BTAUX1KEYB
12VAC
ETHERNET
ETHERNET CONNECTION INDICATOR LIGHT: This indicator is a green
LED, located next to the RJ45 connector on the rear of the terminal. It
lights to indicate a satisfactory connection to the Ethernet circuit (server
or hub).
Note: if the LED does not light, check that the Ethernet connector and cable
both comply with the specifications listed in chapter 4.1.
Installation
Installation Guide - Model 60E 5
2.2.3 - Auxiliary Ports
AX3000 Models 60E have three auxiliary ports as a standard feature:
- MAIN-AUX1: bi-directional serial port, RJ45 connector,
- AUX2: bi-directional serial port, RJ45 connector,
- PARALLEL: parallel port, female 25-pin connector.
Cable pin assignments are listed in chapter 4.
To comply with EMC regulations, the serial cables must be shielded.
2.2.4 - AC Power Connection
An Axel external power transformer must be used, to convert mains voltage at
the wall outlet to low voltage for the AX3000 Model 35.
Before connecting, make sure the AX3000 and monitor power switches are
both in the OFF (0) position.
Plug the plastic moulded cord connector of the external power transformer
(ref. AXP/EC9.8) to the AX3000 power connector. Then plug the transformer
into the AC wall outlet.
IO
SVGA PARALLELAUX2 10BTAUX1KEYB
12VAC
Warning: Only use the Axel external transformer supplied with your
AX3000 Model 60E. Use of any other transformer may cause permanent
damage to the AX3000.
Installation
6 Installation Guide - Model 60E
Plug the monitor power cable into a grounded AC mains power socket. The
monitor does not require low voltage power.
2.2.5 - Power On
The power switch on the rear panel controls the power supply to the AX3000.
1 : On
0 : Off
The green LED on the front of the terminal should light, and a single audible
beep should be heard, to indicate that the AX3000 terminal is powered up and
operating correctly.
To indicate correct keyboard initialisation after power-up, the keyboard indicator
lights 'Num lock', 'Caps lock' and 'Scroll lock' should flash twice.
The green LED on the right side of the RJ45 connector on the back panel
remains lit, to indicate a satisfactory Ethernet connection.
If the terminal does not function as described above (for example if it emits a
continuous tone sound, or two beeps, or if an error message is displayed on the
screen) refer to chapter 5. If the terminal still does not operate properly, call
your service representative.
Table des matières
Autres manuels Axel Terminal tactile
Manuels Terminal tactile populaires d'autres marques
Wincor Nixdorf
Wincor Nixdorf iPOS plus Advanced Manuel utilisateur
Ingenico
Ingenico AXIUM EX4000 Manuel utilisateur
Heisei Electronics
Heisei Electronics Q-POS 815 Manuel utilisateur
Amano
Amano MTX-15 Manuel utilisateur
FLOWBIRD
FLOWBIRD CWT Compact Touch Manuel utilisateur
Demco
Demco SP7 Manuel utilisateur
