AWA UCE1168PR Manuel utilisateur
USB/SD/MP3/CD/Radio
Antique Turntable
INSTRUCTION MANUAL
UCE1168PR
WARNING
E-1
TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
WARNING : SHOCK HAZARD-DO NOT OPEN
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
LIGHTNING FLASH WITH ARROWHEAD SYMBOL -
within an equilateral triangle, is intended to alert the
user to the presence of uninsulated dangerous
voltage within the products enclosure that may be of
sufficient magnitude to constitude a risk of electric
shock to persons.
EXCLAMATION POINT - within an equilateral triangle,
is used to indicate that a specific component shall be
replaced only by the component specified in that
documentation for safety reason.
The following label has been affixed to the unit, listing the proper procedure for working with the laser beam:
CLASS 1 LASER PRODUCT LABEL -
This label is attached to the place as illustrated to inform that the
apparatus contains a laser component.
WARNING LABEL INFORMING OF RADIATION -
This label is placed inside the unit. As shown in the illustration. To
warn against further measures on the unit. The equipment contains
a laser radiating laser rays according to the limit of laser product of
class 1.
CLASS 1 LASER PRODUCT
KLASS 1 LASER APPARAT
LUOKEN 1 LAISERLAITE
KLASSE 1 LASER PRODUKT
SAFETY INSTRUCTIONS
E-2
1. READ INSTRUCTIONS - All the safety and operating instructions should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instruction should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating instructions should be followed.
5. WATER AND MOISTURE - The appliance should not be used near water, for example, near a bathtub, washbowl,
kitchen sink, laundrytub, swimming pool or in a wet basement.
6. VENTILATION - The appliance should be situated so that its location or position does not interfere with its proper
ventilation. Do not place on bed, sofa, rug or similar surface that may block the ventilation openings, in a built-in
installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.
7. HEAT - The appliance should be situated away from heat sources such as radiators, stoves, or other appliances
(including amplifiers) that produce heat.
8. POWER SOURCE - The appliance should be connected to power supply only of the type described in the
operating instructions or as marked on the appliance.
9. GROUNDING - Precautions should be taken to ensure that the grounding means of an appliance is not defeated.
10. POWER CORD PROTECTION - Power supply cords should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them.
11. POWER LINES - An outdoor antenna should be located away from power lines.
12. OBJECT and LIQUID ENTRY - Care should be taken so that objects do not fall and liquids are not spilled into
the enclosure through openings.
13. ESD WARNING - The display does not function properly or no reaction to operation of any the control may due
to the electrostatic discharge. Switch off and unplug the set. Reconnect after a few seconds.
14. DAMAGE REQUIRING SERVICE - The appliance should be serviced by qualified service personnel when:
a. The power-supply cord or plug has been damaged.
b. Objects have fallen into, or liquid has been spilled into the appliance enclosure.
c. The appliance has been exposed to rain.
d. The appliance has been dropped, or the enclosure damaged.
e. The appliance does not appear to operate normally.
15. SERVICING - The user should not attempt to service the appliance beyond that described in the user operating
instructions. All other servicing should be referred to qualified service personnel.
Notes:
a. Dirty or scratched CD may cause a skipping problem. Clean or replace the CD.
b. If an error display or malfunction occurs, disconncet the AC cord and remove all the batteries. Then turn the power
back on.
BEFORE OPERATION
Notes: CONCERNING COMPACT DISCS.
Since dirty, damaged or warped discs may damage the appliance, care should be taken of the followings items:
a. Usable compact discs. Use only compact disc with the mark shown below.
b. CD compact disc only with digital audio signals.
LOCATION OF CONTROL
E-3
PHONO
COVER
AM ANTENNA
AUX - IN JACK
(L/R)
USB SLOT
SKIP +
CD DOOR
OPEN / CLOSE
VOL -
VOL +
LCD DISPLAY
SD CARD SLOT
SKIP -
FUNCTION
BIT RATE
POWER
RECORD
MODE
PROGRAM
PRE-DN
PRE-UP
STANDBY
EXTERNAL
SPEAKER
JACK (L/R)
REMOTE
SENSOR
FM ANTENNA
PLAY/PAUSE
STOP/BAND
AUTO STOP
AC POWER
You can power your appliance by plugging the detachable AC power cord into the AC inlet at the
back of the appliance and into a wall AC power outlet. Check that the rated voltage of your appliance
matches your local voltage.
PHONO COVER ASSEMBLY
1. Push the metal bracket to rear side.
2. Connect the metal bracket to the phono cover.
3. Connect the hinge of the phono cover to the
appliance.
LOCATION OF CONTROL
POWER SOURCE
E-4
TURNTABLE HEAD
TONE ARM
SPEED SELECTOR
PLATTER
1
2
33
BATTERY INSTALLATION
Insert 2 x “AAA” size batteries into the battery compartment. Be sure that the batteries are inserted
correctly to avoid damage to the remote control. Always remove the batteries when the remote
control will not be used for a long period of time, as this will cause leakage to the batteries and
subsequently damage to your set.
Notes:
- Use batteries of the same type. Never use different types of batteries together.
- If the distance required between the remote control and the appliance decreases, the batteries
are exhausted. In this case replace the batteries with new one.
SENSOR WINDOW OF THE RECEIVER
- Even if the remote control is operated within the effective range, its operation may be impossible if
there are any obstacies between the appliance and the remote control.
- If the remote control is operated near other appliances which generate infrared rays, or if other
remote control devices using infrared rays are used near the appliance, it may operate incorrectly.
REMOTE CONTROL
E-5
1. STANDBY
2. TIMER
3. CLOCK
4. 0 - 9
5. PROGRAM
6. INFO MONO / ST.
7. SKIP +
8. STOP / BAND
9. SKIP -
10. X-BASS
11. SLEEP
12. VOL +
13. VOL -
14. P - DOWN
15. P - UP
16. FIND
17. PLAY / PAUSE
18. MODE
19. EQ
20. REC
21. FUNCTION
22. MUTE
1
2
34
514
15
18
17
19
8
11 20
12
10
13
21
22
6
7
9
16
RADIO OPERATION
E-6
AUTOMATIC TUNING
MANUAL TUNING
It is for selecting stations, which cannot be tuned automatically. (manual selection)
To tune a channel manually.
- Skip step 4 in the above procedures.
- In step 3, each time the “SKIP +” or “SKIP -” button is pressed momentarily (0.5 second or less),
the frequency changes by a fixed step:
FM: 0.05 MHz steps
AM: 9 kHz steps
1. Press the “FUNCTION” button to select “TUNER” mode.
2. Press the “STOP / BAND” button to select AM or FM.
3. Press the “SKIP +” or “SKIP -” button to start automatic tuning process.
4. When a station is tuned in the tuning process, it will stop automatically and you can listen to your
desired station.
MEMORY PRESET
1. Repeat step 1 to 4 in the AUTOMATIC TUNING procedures.
2. Press the “PROGRAM” button to start the preset process.
3. Display will show the memory sequence number and a flashing “1”.
4. Press the “P - UP” or “P - DOWN” button or the “PROGRAM” button of front panel to determine
the preset station number.
5. Press again the “PROGRAM” button to preset your desired station.
6. Once all the stations were preset, press the “P - UP” or “P-DOWN” button to listen to your
desired station.
MONO / STEREO
Press the “BIT RATE” button to achieve the best frequency.
CD / MP3 OPERATION
E-7
GENERAL OPERATION
PLAY / PAUSE Press to start playing CD / MP3 disc.
Press again to stop playing CD / MP3 operation temporarily.
Press again to resume playback.
SKIP + & Press to go to the next track or back to the previous track.
SKIP - Press and hold while playing until you find the point of the sound.
STOP Press to stop all CD / MP3 operation.
PLAYBACK
1. Open the CD door and place a CD / MP3 disc with the label up in the CD compartment.
2. Close the CD door.
3. Press the “FUNCTION” button to select “READING”.
4. Focus search is performed if disc is inside. Playback will start automatically from the first track.
5. Adjust the “VOLUME” control to the desired level.
6. Press the “PLAY / PAUSE” button again when you want to stop playback temporarily.
7. Press the “STOP” button when finished.
FOLDER SELECT
Press the “P - UP” or “P - DOWN” button on remote control to select folder. ( Folder select function
can only operate if disc store with at least 2 directories / files. )
MODE
Press the “MODE” button before or during playing CD / MP3 disc,
each press switches the repeat function as follows:
1 - REPEAT 1
3 - REPEAT ALBUM ( For MP3 only )
2 - REPEAT ALL
4 - INTRO
5- RANDOM
6- NORMAL PLAYBACK
REPEAT 1
REPEAT 1
REPEAT
ALBUM
REPEAT
ALL
REPEAT
ALBUM
REPEAT
ALL
NORMAL
PLAYBACK
INTRO
INTRO
RANDOM
RAMDOM
CD / MP3 OPERATION
E-8
PROGRAM
Up to 20 tracks can be programmed for disc play in any order.
Be sure to press the “STOP” button before use.
1. Press the “PROGRAM” button, the display will show “P00 000” and “PROGRAM”.
2. Press the “P - UP” or “P - DOWN” button on remote control to select folder. ( For MP3 only, folder
select function can only operate if disc store with at least 2 directories / files. )
3. Select desired track by using the “SKIP +” or “SKIP -” button.
4. Press the “PROGRAM” button again to confirm desired track into the program memory.
5. Repeat step 2 to 4 to enter additional tracks into the program memory.
6. When all the desired tracks have programmed. Press the “PLAY / PAUSE” button to play the disc
in the order you have programmed.
7. Press the “STOP” button to terminate programmed playback.
USB / SD OPERATION
E-9
GENERAL OPERATION
PLAY / PAUSE Press to start playing tracks from the USB / SD card.
Press again to stop playing USB / SD operation temporarily.
Press again to resume playback.
SKIP + & Press to go to the next track or back to the previous track.
SKIP - Press and hold while playing until you find the point of the sound.
STOP Press to stop all USB / SD operation.
PLAYBACK
1. Plug or slot in USB / SD card device to port. (Make sure no disc on disc tray)
2. Press the “FUNCTION” button to select “READING”.
3. Play will start automatically from the first track.
4. Press the “STOP” button when finished.
5. Press the “PLAY / PAUSE” button again, playback will start from the first track.
Notes:
You can press the “STOP / BAND / USB / SD” button twice during CD playing change to “USB / SD”
mode.
FOLDER SELECT, PROGRAM, REPEAT, RANDOM
The operation of FOLDER SELECT, PROGRAM, REPEAT and RANDOM mode are as the same as
that of CD / MP3. Please refer to CD / MP3 OPERATION.
Table des matières
Autres manuels AWA Platine
