AVS AFM400B Manuel utilisateur

IMPORTANT! For safety reasons, the concrete wall must be

capable of supporting the combined weight of the mount

and the display. The manufacturer takes no responsibility for

failure caused by walls of insuﬃcient strength.

Model: AFM400B

Display Size: 26” to 47”

Maximum Load: 25 kg (55 lbs)

Mounting Pattern: 400 mm x 400 mm (15.7” x 15.7”) max

Tilt Range: up to 10° down

Pan/Swivel Range: up to 180°

Prole: 3.8 cm to 41.5 cm (1.5” to 16.3”)

(A) M8 x 63 Lag Bolt (x2)

(B) Lag Bolt Washer (x2)

(D) M4 x 12 Screw (x4)

(F) M6 x 12 Screw (x4)

(M) S4 Allen Key (x1)

(N) S8 Socket Wrench (x1)

(E) M4 x 20 Screw (x4)

(G) M6 x 30 Screw (x4)

(I) M8 x 30 Screw (x4)

IMPORTANT! For safety reasons, this mount must be secured

to a wood stud capable of supporting the combined weight

of the mount and display. Do not mount to drywall alone.

Part 1A – Mounting to the Wall (Drywall)

SPECIFICATIONS

BOX CONTENTS

HARDWARE KIT

TOOLS REQUIRED

INSTALLATION

(H) M8 x 12 Screw (x4)

Phillips Head Screw Driver

Ratchet or Driver with 13 mm (1/2”) Socket

Electric or Portable Drill

6 mm (1/4”) Drill Bit and Stud Finder for Drywall Installation

10 mm (3/8”) Masonry Bit for Concrete Installation

Level

Mount (x1)

Mount Arm (x2)

Instruction Manual (x1)

Hardware Kit (x1)

Part 1B – Mounting to the Wall (Concrete)

(J) M6 Washer (x4)

Fig. 2

Fig. 3

Use a high quality stud ﬁnder to locate a stud where you

wish to install your mount. Mark both edges of the stud to

help identify the exact center.

NOTE: You must use the center of

the stud to avoid cracking or splitting

the wood during installation.

Carefully remove the plastic covers

from the mount as shown (see Fig. 1).

Place the mount against the wall and

level it using the integrated bubble

level.

While another person holds the

mount in position, mark two

locations for securing the mount to

the wall (see Fig. 2).

Set the mount aside and drill a 6

mm (1/4”) pilot hole at each marked

location.

Place the mount against the wall

over the drilled holes, making sure

the arrow on the mount points up.

Attach the mount to the wall using

the lag bolts (A) and lag bolt washers (B) provided (see Fig. 3).

Do not over-tighten these bolts and do not release the

mount until all bolts are in place. Ensure that the mount

remains level after all bolts are secured.

(K) M8 Washer (x4)

(L) Spacer (x8)

Fig. 1

INSTRUCTION MANUAL

FULL-MOTION WALL MOUNT

fits most flat panel TVs

Thank you for choosing the AVS AFM400B. Before beginning installation, please

check all parts are included and undamaged. For any parts enquiries, please

contact AV Supply Group Ltd on (09) 274 9172 or email to info@avsupply.co.nz

PRODUCT CARE: Periodically clean your mount with a dry

cloth. Inspect all screws and hardware at regular intervals

to ensure that no connections have become loose over

time. Re-tighten as needed.

CAUTION: Do not use this product for any purpose not

explicitly speciﬁed by AVS. Improper installation may cause

property damage or personal injury. If you do not

understand these directions, or have doubts about the

safety of the installation, contact AVS Customer Service or

call a qualiﬁed contractor. AVS is not responsible for damage

or injury caused by incorrect mounting, assembly, or use.

WARNING! This product contains small items that could

be a choking hazard if swallowed. Keep these items away

from young children!

The wall or mounting surface must be capable of

supporting the combined weight of the mount and the

display; if not, the structure must be reinforced.

Locate pipes, wires, or any other hazards in the wall where

you wish to install.

IMPORTANT SAFETY INSTRUCTIONS

Follow all instructions and recommendations regarding

adequate ventilation and suitable locations for mounting

your display. Consult the owner’s manual for your

particular display for more information.

AV Supply Group (AVS) intend to make this manual

accurate and complete. However, AVS makes no claim that

the information contained herein covers all details,

conditions, or variations. Nor does it provide for every

possible contingency in connection with the installation or

use of this product. The information contained in this

document is subject to change without notice or

obligation of any kind. AVS makes no representation of

warranty, expressed or implied, regarding the information

contained herein. AVS assumes no responsibility for

accuracy, completeness or suﬃciency of the information

contained in this document.

6Safety gear and proper tools must be used. Failure to do so

can result in injury or damage.

Part 2 – Attaching the Mount Arms to the Display

(continued)

3202297-130416

OPERATION AND ADJUSTMENT

Fig. 4

Fig. 5

NOTE: This mount comes with a selection of diﬀerent screw

diameters and lengths to accommodate a wide variety of

display models. Not all of the hardware in the kit will be used. If

you cannot ﬁnd the appropriate screw size in the kit provided,

consult the manufacturer of your display for more information.

Part 2 – Attaching the Mount Arms to the Display

IMPORTANT! Use extra care during this part of the installation.

If possible, avoid placing your display facedown as it may

damage the viewing surface.

Part 1B – Mounting to the Wall (Concrete)

(continued)

Set the mount aside and drill a 10 mm (3/8”) hole at each

marked location. Remove any excess dust from the holes.

Insert a concrete anchor (C) into

each hole so that it is ﬂush with the

concrete surface (see Fig. 5). A

hammer can be used to lightly tap

the anchors into place if necessary.

NOTE: If the concrete wall is

covered by a layer of plaster or

drywall, the concrete anchor must

pass completely through the layer

to rest ﬂush with the concrete

surface.

Place the mount against the wall

over the drilled holes, making sure

the arrow on the mount points up.

Attach the mount to the wall using

the lag bolts (A) and lag bolt

washers (B) provided (see Fig. 3). Do not over-tighten

these bolts and do not release the mount until all bolts

are in place. Ensure that the mount remains level after all

bolts are secured.

Carefully remove the plastic covers from the mount as

shown (see Fig. 1).

Place the mount against the wall in the desired location

and level it using the integrated bubble level.

While another person holds the mount in place, mark two

locations as shown for securing the mount to the wall(see

Fig. 4).

Attach the mount arms to the back of your display using

the screws identiﬁed in steps 1 and 2 (see Fig. 6):

If you are using the M4 or M6 screws you will need to use

the M6 washers (J). If you are using the M8 screws you

will need to use the M8 Washers (K).

If you are using the longer screws on a display with a

curved or recessed back, you may also need to use the

spacers (L). Use one spacer or two spacers stacked as

needed. Only use a spacer if necessary.

If the back of your display is ﬂat and the mounting holes

are ﬂush with the surface, you will use the shorter screws

(D, F or H) from the hardware kit.

If the back of your display is curved, has a protrusion, or if the

mounting holes are recessed, you will need to use the longer

screws (E, G or I) and may also need to use the spacers (L).

1Determine the correct length of screw to use by examining

the back of your display:

2Determine the correct diameter of screw to use by carefully

trying one of each size (M4, M6 and M8) from the hardware

kit. Do not force any of the screws – if you feel resistance

stop immediately and try a smaller diameter screw.

IMPORTANT! The latches must be closed and locked at

all times to prevent the display from being accidentally

knocked from the mount.

To change the tilt angle of your display, have one person

hold the display ﬁrmly in place while another person

loosens the tilt screws

using the S4 Allen key

(M) from the hardware

kit (see Fig. 8). Once

loosened, move your

display to the desired

position and then

re-tighten the screws

to lock the angle in

place.

Do not release

the display until both

tilt screws are fully

tightened and never remove the tilt screws.

Swivel adjustments can be made by grasping the display

ﬁrmly and moving it to the desired position. Be careful

that ﬁngers or cables do not get pinched when moving

the mount.

Level correction adjustments can be made by simply

rotating the display in

the needed direction. If

it is too diﬃcult to

move the display or if

the display does not

stay in position once

moved, adjust the

tension of the four nuts

located behind the

face plate using the S8

socket wrench (N)

provided in the

hardware kit (see Fig. 9). Adjust all four nuts evenly.

Do not

fully loosen or remove these nuts.

With the help of another person, carefully lift your display

and place it on the mount.

Do not release the display

until the mount arms have securely hooked onto the

mount.

Close the safety latch at the

bottom of each arm to prevent

the display from being lifted

from the mount. Each latch will

automatically lock when fully

closed

(see Fig. 7)

Re-attach the plastic covers that we removed in part 1.

Cables can be routed through the channel located on the

bottom of the mount to keep them organized and out of

the way.

Part 3 – Final Assembly

Fig. 6

For displays with curved or

recessed backs.

For displays with

at backs.

Fig. 7

Fig. 8

Fig. 9

Part 3 – Final Assembly

(continued)

Autres manuels AVS Support TV

AVS

AVS AIFM4040 Manuel utilisateur

Manuels Support TV populaires d'autres marques

Ergotron

Ergotron Neo Flex Cantilever UHD Manuel utilisateur

StarTech.com

StarTech.com FPCEILBTB Manuel utilisateur

VonHaus

VonHaus 05/038 Manuel utilisateur

Techlink

Techlink ECHO TV Manuel utilisateur

Sandstrom

Sandstrom SSTVMC12X Manuel utilisateur

Sony

Sony SU-WL700 Mode d’emploi

ICW

ICW SCACC18 Manuel utilisateur

LG WM-L640V Manuel utilisateur

Gembird

Gembird WM-65ST-01 Manuel utilisateur

ERARD

ERARD FiTUP XXL 035320 Manuel utilisateur

PEERLESS

PEERLESS PLCK-1 Mode d’emploi

Kanto

Kanto RCF180 Manuel utilisateur

GEM

GEM GEM GP001 Manuel utilisateur

Gladiator Joe

Gladiator Joe GJ0A0053 Manuel utilisateur

Vivotek

Vivotek AM-105 Manuel utilisateur

Vivo

Vivo VESA STAND-VAD1B Manuel utilisateur

AmazonBasics

AmazonBasics B07QG3LMG4 Manuel utilisateur

Secura

Secura QLF210 Manuel utilisateur