AVPro Edge AC-MX88-UHD Manuel utilisateur
AC-MX88-UHD AVProEdge 2222 E 52nd St N ~ Sioux Falls, SD 57104 1-877-886-5112 ~ 605-274-6055support@avproedge.comAC-MX88-UHD
8x8 HDMI Matrix w/ Audio De-Embedding 4K 60Hz, HDMI 2.0 and HDCP 2.2 Compatible
AC-MX88-UHD
The AC-MX88-UHD is a true 8x8 HDMI matrix switch. Supporting HDMI 2.0, HDCP 2.2, up to 4K video resolution, and up to 10.2 Gbps bandwidth. This switch allows any source (Blu-ray, UHD Blu-ray, satellite receiver, game consoles, PCs, etc...) to be shown on any of the connected displays.This matrix equalizes and amplifies the output to ensure the HDMI signal can be transmitted through long HDMI cables without loss of quality. You can extend your distance further with the AC-EX70-UHD HDMI Extender. Full EDID management allows maximum flexibility with todays wide mixture of sources and displays.This is an ideal solution for digital entertainment centers, HDTV retail, show sites, data centers, schools, conference and training centers and more!Features:•HDMI 2.0 (10.2 Gbps)•HDCP 2.2 compliant•De-embed SPDIF audio on each output•Independent source/display switching•Up to 4K Resolution (4K60 4:2:0)•HDR Supported•IR & RS-232 ControlEasy to use:•Install in seconds•Feature rich•Powerful EDID management•Front Panel Control•IR Remote•IR & RS-232 Control•LAN ControlDevice Overview:
AC-MX88-UHD
Figure 1
~ AC-MX88-UHD Panel Controls
NOTE: There is an application diagram on page 11 of this manual.In The Box:•AC-MX88-UHD Matrix Switch•IR Remote Control•IR Extension Cable•12V/3A Locking Power Supply•Instruction Manual Quick Installation:1. Connect the HDMI input sources (Blu-ray, Set Top Box, etc...) to the AC-MX88-UHD2. Connect the HDMI output devices (AVR, Display, Distribution Amplifier, Extender) to the AC-MX88-UHD3. Power on the sources4. Connect the power supply into the AC-MX88-UHD5. Turn on output devices/displays6. You may now use the front panel controls, supplied IR remote or free PC software to control the switch. * For advanced programming please see the RS-232 commands on page 7Front Panel Control:The AC-MX-88-UHD front panel controls allow for the selection of the inputs to the various outputs. First press a button on the OUTPUT row to choose the output port, then press a button on the INPUT row to select the input signal for the selected output. (Output, then Input)
Select Output First --><-- Then Select Your Input
AC-MX88-UHD
IR Remote Control:The HDMI routing of the matrix can also be controlled by using the IR remote supplied with the product.The left arrow button decrements to the next lower input port, and the right arrow increments to the next input port.Figure 2 ~ AC-MX88-UHD IR RemoteAdditionally, the supplied IR Extension Cable can provide a different receiver position. Just plug into the IR Extension Socket on the back of the matrix and place the receiver in a more convenient location.Figure 3 ~ AC-MX88-UHD IR ControlsFigure 4 ~ IR Extension Cable
AC-MX88-UHD
Press and hold INPUT button 3 for 3 secondsContinue to "click" INPUT 3 to toggle through the EDID settings. (Keep "clicking" to toggle through all of the EDID settings listed above.)Press and hold INPUT 3 for 3 more seconds to save the EDID as shown on the displayBonus Feature!Pressing and holding the any OUTPUT button will automatically read, store and apply the EDID from the display device to the current INPUT assigned. It will be stored in USER EDID 1. EDID Management:This matrix has 12 factory defined EDID settings. It also has 3 user defined EDID memories. The user EDID memories are independent to each input and can be set differently. The user defined EDID can be uploaded using the free PC Control software or RS-232. In addition, you can choose to read the EDID from the desired output and that read EDID will automatically store and overwrite the EDID in "USER EDID 1". We recommend uploading custom EDID settings to memory 2 or 3.By default the matrix is set to a 1080P EDID, this is to maximize plug and play capability. When using 4K sources, you will want to define a 4K EDID on that input (or read from the display).To Change the EDID setting:1. Press and hold the INPUT you want to change for 3 seconds2. Now "click" desired INPUT to toggle through the available EDID options3. Once you are on the EDID you want to select, press and hold for 3 seconds again.This will set the EDID for the desired input. Please see the example below for detailed instructions. These are the pre-defined EDID settings that you can toggle through:1 - 1080P 2CH (PCM)2 - 1080P 6CH (5.1 Channel)3 - 1080P 8CH (7.1 Channel)4 - 1080p 3D 2CH (PCM)5 - 1080P 3D 6CH (5.1 Channel)6 - 1080P 3D 8CH (7.1 Channel)7 - 4K30Hz 3D 2CH (PCM)8 - 4K30Hz 3D 6CH (5.1 Channel)9 - 4K30Hz 3D 8CH (7.1 Channel)10 - 4K60Hz (Y420) 3D 2CH (PCM)11 - 4K60Hz (Y420) 3D 6CH (5.1 Channel) 12 - 4K60Hz (Y420) 3D 8CH (7.1 Channel)USER EDID 1 USER EDID 2 USER EDID 3EDID from output 1 EDID from output 2 EDID from output 3 EDID from output 4EDID from output 5EDID from output 6EDID from output 7EDID from output 8
AC-MX88-UHD
EDID Management Cont:The first 12 EDID settings cannot be altered. The three USER EDID settings are programmed using RS-232 or the free PC Software. However, you can read an EDID from any output and it will automatically store in USER EDID 1. Remember, each INPUT has an independent EDID setting and you may need to program each one.To read and set an EDID to a specified input the steps are the same as on PAGE 5. The only difference is that when you see a screen similar to FIGURE 5, you press and hold the INPUT button again for 3 seconds and this AUTOMATICALLY reads, stores and sets the EDID for that INPUT.
Figure 5 ~ Read EDID ScreenDisplay IP Data:Press and hold INPUT 3 and INPUT 4 at the same time for three seconds to display the current IP settings. This screen will change every 3 seconds showing additional settings (host, net mask, router IP). NOTE: This screen always starts with the current IP address of the matrix:In order to prevent potential IP problems, most IP settings have to be managed in the Free PC Software or using RS-232 commands.NOTE: The default IP address is 192.168.001.239 (As pictured above)You can enable/disable DHCP mode directly from the front panel. When DHCP is enabled it will automatically gather an IP address from the network and it will be discoverable on said network. You can now view the assigned IP address by following the steps above. To toggle DHCP, press and hold INPUT 1 and INPUT 4 at the same time for three seconds. You will see this:Cascade Mode:When Cascade Mode is turned on, the signal is passed from the switch without reading EDID or Hot Plug. Many issues can be resolved in the field with this mode, including:•Invalid/incorrect EDID coming from display (It happens more than you think)•When you want to manage EDID in a device further down the chain (AVR or Distribution Amp)•When running one or more outputs into additional peripherals before the display We recommend you ONLY use cascade mode if you have exhausted all other troubleshooting options. To toggle Cascade Mode press and hold INPUT 1 and INPUT 2 at the same time for three seconds. When Cascade Mode is enabled you will see this:
AC-MX88-UHD
AC-MX44-UHD and AC-MX88-UHDThe same commands can be sent to the matrix using Ethernet as IP commands NOTE: To see a connection diagram of how connect to the matrix using RS-232, see the connection diagram at the end of the manual.RS-232 Commands:EDID Commands:External Audio Commands:Switching Commands:Cascade Mode Commands:
AC-MX88-UHD
IP Set-Up Commands:Get Status Commands:Other Commands:
AC-MX88-UHD
AC-MX88-UHD
SPDIF audio OutputsNOTE: HDR (High Dynamic Range) is supported on these matrix switchers. you mus read EDID from and HDR capable display and store it to to the input where the HDR source resides. Specifications:10.2 GbpsHDCP 2.2 and earlierHDCP Versions8885.3lbs
AC-MX88-UHD
AVProEdge.Safety Instructions:After Sale Service:
Autres manuels pour AC-MX88-UHD
1
Table des matières
Autres manuels AVPro Edge Commutateur matriciel
AVPro Edge
AVPro Edge AC-MX1616-OUT-AUHD-NS Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX1616-AUHD-HDBT Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX44/88-AUHD-HDBT Manuel utilisateur
AVPro Edge
AVPro Edge AC-CX42-AUHD Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX88-AUHD-NSFS Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX-88X Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX-88HDBT Manuel utilisateur
AVPro Edge
AVPro Edge ConferX AC-CX42-AUHD Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX88-UHD Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX-82 Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX-42 Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX-44HDBT Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX-44 Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX44-AUHD-HDBT Manuel utilisateur
AVPro Edge
AVPro Edge ConferX AC-CX84-AUHD Manuel utilisateur
AVPro Edge
AVPro Edge CLOUD 9 Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX1616-AUHD Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX-42X Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX9XHDL-HDBT Manuel utilisateur
AVPro Edge
AVPro Edge AC-MX42-AUHD Manuel utilisateur
