Avocent Cybex SwitchView Manuel utilisateur

Powering your system

Locate the power cord that came with your switch.

Plug one end into the IEC power connector on

the SwitchView SC8 DVI switch. Make sure that

the power switch is off, then plug the other end

of the power cord into an appropriate AC wall

outlet. Power up your switch ﬁrst, then power up all

attached servers.

The Power of Being There®

Quick Installation Guide

Cybex®SwitchView®

SC8 DVI Switch

The following instructions will help you

install and use your SwitchView SC8

DVI switch.

Should you require further assistance, please

contact Avocent Technical Support.

To install the Cybex SwitchView SC8 DVI switch

To Contact Avocent Technical Support CALL (888) 793-8763 VISIT www.avocent.com/support DOWNLOAD www.avocent.com

Avocent, the Avocent logo, The Power of Being There, Cybex and SwitchView are registered trademarks of Avocent Corporation or its afﬁliates. ©2005 Avocent Corporation. All rights reserved. 590-502-501A

Connecting your local peripherals to

the SwitchView SC8 DVI switch

Power down all servers that will be part of your

SwitchView SC8 DVI switching system. Locate

your PS/2 keyboard, DVI monitors and PS/2

mouse.

Plug your DVI monitor cables into the

CONSOLE ports on the left side of the back

of your switch

. Plug your PS/2 keyboard cable

and your PS/2 mouse cable into the keyboard

and mouse ports respectively.

Connecting your servers to the

SwitchView SC8 DVI switch

Locate your ﬁrst cable set consisting of two

PS/2 cables and one or two DVI cables. The

SwitchView SC8 DVI switching system has eight

port sets labeled A-H on the rear of the unit. Plug

one end of the two PS/2 cables (keyboard and

mouse) and one end of a DVI cable (monitors)

into the corresponding ports on your computer.

Plug the other ends into any available server port

set on yourSwitchView SC8 DVI switching system.

Repeat this process until all servers are properly

attached to the SwitchView SC8 DVI switch.

CONSOLE HG F E DCBA

Power down all

connected servers.

Connect your

peripherals to the

CONSOLE ports

on the switch.

Connect the eight

servers to the

switch with the

provided cables.

Press the

appropriate front

panel button

labeled A-H to

access servers in

your system.

Switching your servers

Press the appropriate front panel button labeled

A-H to access another server in your SwitchView

switching system.

Power up

your system.

USA Notiﬁcation

Warning: Changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

Canadian Notiﬁcation

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Safety and EMC

Approvals and Markings

UL, FCC, cUL, ICES-003

Safety Precautions

NOTE: The AC inlet is the main disconnect.

INSTRUCTIONS

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

DANGEROUS VOLTAGE

This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s

enclosure that may be of sufﬁcient magnitude to constitute a risk of electric shock to persons.

RACK MOUNT SAFETY CONSIDERATIONS

• Elevated Ambient Temperature: If installed in a closed rack assembly, the operation temperature of the rack

environment may be greater than room ambient. Use care not to exceed the rated maximum operating temperature of

40° C for this product.

• Reduced Air Flow: Installation of the equipment in a rack should be such that the amount of airﬂow required for safe

operation of the equipment is not compromised.

• Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous condition is not

achieved due to uneven mechanical loading.

• Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and

the effect that overloading of circuits might have on overcurrent protection and supply wiring. Consider equipment

nameplate ratings for maximum current.

• Reliable Earthing: Reliable earthing of rack mounted equipment should be maintained. Pay particular attention to

supply connections other than direct connections to the branch circuit (for example, use of power strips).

Ce manuel convient aux modèles suivants

Autres manuels Avocent Changer

Avocent

Avocent DSR 1024 Instructions d'installation et d'entretien

Avocent

Avocent AutoView 416 Instructions d'installation et d'entretien

Avocent

Avocent SwitchView SwitchView SC Manuel utilisateur

Avocent

Avocent SWITCHVIEW PC Manuel utilisateur

Avocent

Avocent DSR Series DSR1020 Mode d’emploi

Avocent

Avocent AutoView 416 Instructions d'installation et d'entretien

Avocent

Avocent SwitchView SC120 Manuel utilisateur

Avocent

Avocent SwitchView Manuel utilisateur

Avocent

Avocent Eletric Keyboard Instructions d'installation et d'entretien

Avocent

Avocent SwitchView IP 1020 Manuel utilisateur

Avocent

Avocent DSR1161 Manuel utilisateur

Avocent

Avocent AutoView 2000 AV2000BC AV2000BC Instructions d'installation et d'entretien

Avocent

Avocent SwitchView SC380 Manuel utilisateur

Avocent

Avocent DSR Series DSR1021 Manuel utilisateur

Avocent

Avocent DSR Series DSR2161 Manuel utilisateur

Avocent

Avocent AutoView 1400 Manuel utilisateur

Avocent

Avocent DSR Series DSR1022 Manuel utilisateur

Avocent

Avocent AMX5010 Manuel utilisateur

Avocent

Avocent DSR Series DSR1020 Mode d’emploi

Avocent

Avocent DSR Series DSR4030 Manuel utilisateur

Avocent

Avocent SwitchView Manuel utilisateur

Avocent

Avocent DSR Series DSR4030 Manuel utilisateur

Avocent

Avocent DSR Series DSR1021 Instructions d'installation et d'entretien

Avocent

Avocent AutoView 1515 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur