Avigilon NVR5-STD-2NDCPU Manuel utilisateur
Avigilon NVR5 Standard 2nd
CPU Kit Installation Guide
Installation Guide
NVR5-STD-2NDCPU
For
NVR5 STD 16TB-64TB
1
© 2022,Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILON are trademarks
of Avigilon Corporation. Intel is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other
countries. Other names or logos mentioned herein may be the trademarks of their respective owners. The
absence of the symbols ™ and ® in proximity to each trademark in this document or at all is not a disclaimer of
ownership of the related trademark.
This document has been compiled and published using product descriptions and specifications available at
the time of publication. The contents of this document and the specifications of the products discussed
herein are subject to change without notice. Avigilon Corporation reserves the right to make any such
changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the
completeness or accuracy of the information contained in this document; or (2) is responsible for your use of,
or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages
(including consequential damages) caused by reliance on the information presented herein.
Avigilon Corporation
avigilon.com
20220617
2
Introduction
Avigilon provides an optional 2nd CPU kit for the NVR5 Standard. These kits provide all the components
needed to add CPU redundancy to an NVR.
Part Number Description
NVR5-STD-2NDCPU NVR5 Standard 2nd CPUKit
Important: A second power supply (NVR5-PSU-800W) is required in order to enable the 2nd CPUKit
in the NVR5 Standard system.
Confirm Package Contents
Confirm that the kit you are installing contain the following components:
l2nd CPU Kit (NVR5-STD-2NDCPU):
o1 × Intel Xeon Silver 4309Y
o1 × R750xs Heat Sink Customer Kit
o2 × 8 GB - 3200 Mhz DDR4 RDIMMs
Recommended Tools
The following tools are not included in the kit package, but are needed to complete the installation:
lPhillips #2 screwdriver
lTorx #T30 screwdriver
lWrist-grounding strap connected to the ground
lESD Mat
Important: It is recommended that you always use an antistatic mat and antistatic strap while
working on components inside the system.
Introduction 4
Installing the NVR5 2nd CPU Kit
Note: If the NVR5 is an operating part of your security system, be aware that it must be shut down to
complete this procedure.
Before starting to install the kit:
1. Turn off the NVR5, including all attached peripherals. Press the power button on the front panel, and
wait for the light to stop blinking to indicate shutdown is complete.
WARNING — Opening or removing the system cover while the system is powered on may
expose you to a risk of electric shock.
2. Disconnect the NVR5 from the electrical outlet and disconnect the peripherals.
3. Remove all network, power and peripheral cables from the NVR5.
4. If applicable, remove the NVR5 from the rack.
Important: Whenever you need to lift the system, get others to assist you. To avoid injury, do
not attempt to lift the system by yourself.
Installing the NVR5 2nd CPU Kit 5
Opening the Cover
1. At the top of the NVR5, unlock the latch release then lift and rotate the latch towards the back of the
unit. The cover slides back and is released from the body.
Tip: Use a Phillips #2 screwdriver to remove the shipping screws before unlatching the cover
if you are removing the cover of an NVR5 for the first time.
2. Remove the air shroud by holding it at both ends and lifting it away from the system.
Opening the Cover 6
3. View the interior of the NVR5 and identify the locations where the components of the kit will be
installed.
The view below shows the details of an NVR5 with all of the covers and cards removed, and important
components labeled with numbers.
The components affected by the NVR5 Standard 2nd CPU Kit are:
l3—Memory module
The DIMMs in the kit are installed here.
l10—CPU2 processor and heat sink module socket (with dust cover)
The second CPU in the kit is installed here.
Note: The other components pointed out in the diagram are not affected by installing the
NVR5 Standard 2nd CPU Kit.
Opening the Cover 7
Installing the CPU
You need the processor bracket, processor (CPU), and heatsink provided in the kit to complete this
procedure.
With the NVR5 open and the protective cover removed:
1. Unpack the CPU.
2. Place the processor in the processor tray.
Note: Ensure that the pin 1 indicator on the processor tray is aligned with the pin 1 indicator on
the processor.
3. Place the processor carrier on top of the processor that is in the processor tray aligning pin 1 indicator
on the processor.
Note: Ensure that the pin 1 indicator on the bracket is aligned with the pin 1 indicator on the
processor before carrier on the processor.
4. Align the processor with processor carrier by using your fingers to press the carrier on all the four
sides until it clicks into place.
Note: Ensure that the processor is securely latched to the processor carrier.
Installing the CPU 8
5. Unpack the heat sink and remove the protective film from the base of the heat sink. Be careful not to
touch the thermal paste that is pre-applied to the bottom of the heat sink.
6. Place the heat sink on the processor and press the heat sink until the carrier locks onto the heat sink at
all the four corners.
Important: To avoid damaging the fins on the heat sink, do not press down on the heat sink
fins.
lEnsure that the pin 1 indicator on the heat sink is aligned with the pin 1 indicator on the carrier
before placing the heat sink onto the processor carrier.
lEnsure latching features on processor carrier and heat sink are aligned during assembly.
Installing the CPU 9
7. Locate the 2nd processor socket and pull off the CPUdust cover over the socket.
8. Align the pin 1 indicator of the processor heat sink module (PHM) to the system board and then place
the processor heat sink module (PHM) on the processor socket.
Important: Ensure that the processor and heat sink module is held parallel to the system
board to prevent damaging the components.
Important: Do not force the processor into the socket. The processor should slide easily into
the socket when aligned correctly.
Installing the CPU 10
Table des matières
Autres manuels Avigilon Matériel informatique
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
