Avery Dennison TTX 207 Manuel utilisateur

04/02 Rev. 2.15-01 MANUAL Page 1

TTX 207 – Da Capo

Setup, Operation, Service

General notes ............................................... 2

Before usin

the printer.... ......................... 2

Cop

ht ................................................... 2

Initiation ......................................................... 3

Unpackin

the printer ................................ 3

Settin

up and connectin

the printer ....... 3

Connections .................................................. 4

Insertion/removal of material ......................... 5

Operation ...................................................... 6

Connectin

to a computer / startin

.......... 6

Functions of displa

s .......................... 6

Functions of LED elements ....................... 6

ustment of DIP switches ...................... 7

Maintenance and care .................................. 8

Chan

and cleanin

the printhead ....... 8

Cleanin

the feed roller ............................. 9

Cleanin

ap sensor ............................. 9

Cleanin

of material

uidin

parts ............. 9

Label material ............................................. 10

Trouble shootin

..........................................11

Status Printout ............................................. 13

Sensor Check Routine ................................13

Access to routine .....................................13

Gap sensor ..............................................13

Micro switch/printhead lever ....................13

Material end sensor .................................13

Technical Specifications ..............................14

Anhan

/ Appendix ......................................16

Zeichensatztabelle / Font table ................16

Linien und Rechtecke / Lines and rectan

les

Interne Fonts / Internal fonts ....................18

Interne Barcodes / Internal bar codes ......21

Index ............................................................22

04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 2

TTX 207 – Da Capo

General notes

Before using the printer....



The followin

warnin

hints and precautions contained in these Operatin

In-

structions must be strictl

observed. This will considerabl

contribute to the

safe and expert operation of

our printer.



Exclusivel

ori

inal parts and accessories available from the manufacturer

are to be used in order to maintain the service life of

our prlnter. The use of

parts not in compliance with the exactin

demands made b

the manufactu-

rer ma

result in unnecessar

sources of troubles.



The housin

of the unit must exclusivel

be opened b

authorized technical

personnel onl



Insertion/Exchan

e material should be carrled out onl

especiall

instruc-

ted personnel (Set Up Mode!).



On operation with open cover, fin

ers, hair, clothes,

ewelr

, etc. ma

cau

ht b

and

et into the unit in the print modul.



At a material width less than 65 m the thrust screw has to be ti

htend.



Release printhead b

openin

the pressin

lever durin

lon

er periods of no

operation.



Wait at least 10 seconds before switchin

unit back „ON“.



Do not remove, insert or exchan

e PLUG IN CARDS until after at least 60

seconds from switchin

„OFF“ the device.

This User Manual and its contents are sub

ect to cop

ht. The publisher‘s

prior written consent must be obtained for reproduction of the Manual as a

whole or part thereof.

Aver

reserves the ri

ht to technical and other alterations without prior notice.

04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 3

TTX 207 – Da Capo

Initiation

Unpacking the printer

1. Remove top foamed packin

2. Take printer out of cardboard box.



For carr

our printer, take it b

the base plate.



Front cover, reel holder and motor of optional knife must not be used as car-

handles.

Setting up and connecting the printer

1. Check mains volta

e settin

and fuses.

– The fuses can be replaced b

removal of the fuse element (Fi

. 1).

–Mainsvolta

e variation is possible b

turnin

the insert.

2. Insert current suppl

into linin

desi

nated for this purpose at the rear side

of unit.

3. Switch „ON“ of unit.

CAUTION!

Mains volta

e can kill

ou!

– Pull off the mains connector befor you check or change the mains voltage

setting!

– Pull off the mains connector befor you check or replace the fuse!

04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 4

TTX 207 – Da Capo

Connections

All connectors are located at the rear side.

A Centronics or alternativel

a serial V.24/DB 25 (RS232) interface interface

is inte

rated.



Before connectin

/disconnectin

the interface cable and the stacker switch

„OFF“ all devices.



Onl

devices ma

connected to the interface and stacker connector which

are approved to ICE 950 and VDE 0805 and are in compliance to SELV.

Fig. 1: Connections on the printer backside.

(not supported)

04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 5

TTX 207 – Da Capo

Insertion/removal of material

1. Han

document material in reel holder in a wa

to ensure anticlockwise

unwindin

2. Open pressure lever (red).

3. Insert material underneath the printhead accordin

to sketch, further mate-

rial transport is automaticall

4. Close pressure lever.

5. When usin

notched material, ad

ust

ap sensor to the

ap position.



At a material width less than 65 m the thrust screw (Fi

. 2) has to be ti

hte-

ned.

6. Switch „ON“ printer - the

reen LED

lows at the operation panel (eventuall

switch to OFFLINE). B

depression of the FEED-ke

a material feed can be

advanced. At punched material one label len

th is advanced, continous

material is transport as lon

as FEED-ke

is operated.

Removal of material Material can be removed after openin

the pressure lever.

Fig. 2: Material winding diagram.

CAUTION!

Dan

er of pullin

in and tearin

off of hair,

eweller

, loose clothin

, etc.!

– Don´t let long hair, loose sleeves, jewellery, etc. hang into the printer!

04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 6

TTX 207 – Da Capo

Operation

Connecting to a computer / starting

1. Connect interface cable from computer to the printer. Switch on the printer,

the

reen LED

lows (LED =small, round li

ht emittin

element).

2. B

depressin

the ON/OFF ke

, the printer is switched to „ONLINE mode“,

the

ellow LED

lows and the printer is read

to receive data and to print

labels.

Functions of display keys

ON / OFF – Switch to the ONLINE or OFFLINE mode. ONLINE mode is indicated b

the

ellow LED, the unit is read

to receive data.

– Control break of a print

ob, the

ellow LED flashes fast - rest quantit

– If an error is indicated (red LED) the error will be confirmead after its cor-

rection b

depressin

the ON/OFF ke

FEED – In the OFFLINE mode a material feed can be advanced. At punched ma-

terial one label len

th is advanced, continous material is transport as lon

as FEED-ke

is operated.

– If an error is indicated the error code ma

be called off via the

ellow LED

– The controlled break of a current print

ob will be cancelled.

CUT Reserved for optional functions.

Functions of LED elements

The operation panel shows 3 LED‘s in order to indicate the operation modes.

POWER (Green) This LED

lows, if printer is switched on.

ERROR (Red) Indication of an error (end of media........)

DATA (Yellow) LED

lows if printer is switched to ONLINE mode.

– LED flashes if unit prints, receives data or

enerates an ima

– LED flashes fast if current print

ob is interrupted - rest quantit

– Indication of error code with 5 short/lon

flash si

nals called off b

pressin

the FEED ke

04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 7

TTX 207 – Da Capo

Adjustment of DIP switches

Left of the mains plu

there are located 8 DIP switches (Fi

. 1) with which the

parameters ma

usted as follows.



A modification of a DIP switch position will be effictive after newl

switchin

„ON“ the device.

Fig. 3: DIP switch settings.

04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 8

TTX 207 – Da Capo

Maintenance and care

Carefull and re

ular maintenance will raise the performance and lon

evit

the printer, especiall

that of the printhead. Generall

ard: Keep an

dirt

out off the print module! Remove an

deposits of paper, adhesive and pre-

print colors off the printhead, feed roller and

ap sensor periodicall

Changing and cleaning the printhead

1. Switch unit off and pull off mains plu

2. Open pressure lever.

3. Remove material.



Disconnect printhead plu

after at least 3 minutes from switchin

off the unit!

4. Unscrew knurled screws at printhead holder and remove.

5. Draw out the printhead carefull

6. Clean print head with dust-free cloth and cleansin

liquor onl



Metal ob

ects must never

et into contact with printhead surface! Never use

knives or ob

ects with sharp ed

es for cleanin

7. Proceed assembl

of printhead in reverse order.

Special care is to be taken that printhead is supported flush on holdin

plate

and completel

flush towards the

uide mechanism (looks like a tooth) (Fi

4) to warrant inprint accordin

to the O-line as well as dama

es of the prin-

thead.

Fig. 4: The print head must cling thightly to its holder (upper figure).

04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 9

TTX 207 – Da Capo

Cleaning the feed roller

1. Switch unit off and pull off mains plu

!<D>

2. Remove material.

3. Remove insertion plate b

loosen two knurled screws below the plate.

4. Clean the accessable section of print roller with dust-free cloth and clean-

sin

liquor onl

. Advance print roller b

switchin

on the printer, close prin-

thead lever,press FEED ke

- the roller turns a quarter round.

5. Switch unit off and pull off mains plu



Never use knives or ob

ects with sharp ed

es for cleanin

Cleaning of gap sensor

Accordin

to the materials applied, the li

ht barrier is to be cleaned from ma-

terials residues and dust b

means of compressed air.

With heav

contamination additional cleanin

usin

a dust-free cloth and

cleansin

liquor is recommended.

Cleaning of material guiding parts

Accordin

to the materials applied an

residues at material baffles is to be

cleaned re

ularl

Contaminated surfaces influence the feed of material which will reduce the

print qualit

04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 10

TTX 207 – Da Capo

Label material

The printer is desi

ned for thermal direct printin

. The label material should

be of low abrasive behaviour of the surface structure and low start tempera-

ture for the colour development.

If the material is extremel

abrasive, the printhead is faster worn as usual.

Similar conditions prevail with hi

h start temperature. Material and printhead

require a lon

er coolin

down period, the printin

qualit

is more critical and

the printhead is faster worn as on a normal rate.

Fig. 5: Specifications for label material.

Table des matières

Autres manuels Avery Dennison Imprimante

Avery Dennison

Avery Dennison Platinum 6039 Manuel du propriétaire

Avery Dennison

Avery Dennison Wireless Ethernet Print Server Monarch 7411 Manuel utilisateur

Avery Dennison

Avery Dennison Monarch 9419 Manuel de service

Avery Dennison

Avery Dennison M09416 TTXLI Manuel utilisateur

Avery Dennison

Avery Dennison Pathfinder 6140 Manuel utilisateur

Avery Dennison

Avery Dennison Monarch ADTP1 Manuel de service

Avery Dennison

Avery Dennison AP7.t Manuel utilisateur

Avery Dennison

Avery Dennison Pathfinder6057 Manuel d'utilisation et d'entretien

Avery Dennison

Avery Dennison Monarch 9855 Manuel utilisateur

Avery Dennison

Avery Dennison AP5.4 Manuel utilisateur

Avery Dennison

Avery Dennison Monarch ADTP2 EcoCut Manuel de service

Avery Dennison

Avery Dennison SNAP 700 Manuel d'utilisation

Avery Dennison

Avery Dennison Monarch ADTP1 Manuel de service

Avery Dennison

Avery Dennison Pathfinder 6057 Manuel de service

Avery Dennison

Avery Dennison Monarch 9460 Manuel utilisateur

Avery Dennison

Avery Dennison Monarch 9493 SNP Manuel d'utilisation et d'entretien

Avery Dennison

Avery Dennison Monarch 9855 RFID Manuel de service

Avery Dennison

Avery Dennison Monarch Pathfinder Ultra Platinum 6039 Manuel utilisateur

Avery Dennison

Avery Dennison AP7.t Manuel utilisateur

Avery Dennison

Avery Dennison Monarch Pathfinder Ultra Silver Manuel utilisateur

Avery Dennison

Avery Dennison SNAP 500 Manuel utilisateur

Avery Dennison

Avery Dennison SNAP 700 Manuel d'utilisation

Avery Dennison

Avery Dennison Monarch Tabletop Printer 2 Manuel utilisateur

Avery Dennison

Avery Dennison Monarch 9485 Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur