Avent Security M901S Manuel utilisateur
M901S
FINGERPRINT DOOR LOCK
Brief Introduction
Product Guide
1
1The lock is only suitable for the glass door which the thickness is between
10 ~ 12mm.
2There are up to 300 different users available in the lock.
3The password can be set between 6 ~ 10 digits.
4The default master password is “01234-56789”.
5The lock has 3 unlocking modes for different security levels;
6When operating the lock, the number keys have different functions
7Once user input wrong passwords in continuous for 5 times, the lock freezes
for 3 minutes for security. During this period, you cannot operate the lock.
“2":
Up ( )
“4":
Left (<)
“6":
Right (>)
“8":
Down ( )
Fingerprint Sensor
OLED Display
Touch Screen Keypad
Lock Knob
Installation
2
Mark the place on the glass
door for the installation, and
then paste the base board
on it.
aLoose the screws on the back side
of the lock, disconnect the
cable on the lock, and then insert
the lock into the base board
bConnect the cable with the back
plate of the lock, and then fasten
the lock
c
Install the battery and try to
unlock the lock to make sure
the installation is correct.
dFor the strike plate, make the
place on the glass door according
to the place of the lock, and then
paste and base board on it
eInsert the strike plate into the
base board and finish.
f
Some Suggestions to Help Capturing the Fingerprint
1
When placing the finger on the sensor, please make sure the “core” of fingerprint is staying
in the main area of sensor directly with a little amount of pressure. Like the pictures show as below:
Insert Image
The sensor may not capture the correct fingerprint image if you follow the below operations.
Insert Image
It is suggested to register the thumb, first finger, and middle finger for better
fingerprint images.
Operation
3
Place the finger on the sensor, the lock will be activated automatically and started to capture the
fingerprint image for identification. Once the identification is passed, the LCD display shows the
user information and then unlock automatically.
Touch the keypad to activate the lock, and then input the password with press “#” to finish. If the
password is correct, the LCD display shows the user information and then unlock automatically.
***
if you input a wrong password continuously for 5 times, the lock will be locked
for 30 seconds. The LCD display shows count down of time. During this period,
the lock cannot be accessed, and all operations are suspended. Afterwards, the
lock returns to normal state.
+
2Fingerprint Unlocking
3Password Unlocking
#
4
USER INFORMATION
USER INFORMATION
Random Password Protection
For a better security protection to the password user, the lock is designed with a random
password protection. You can add any digits before and after the real password.
For example, the password is “123-456”, you can unlock the lock by inputting the password
as following:
1:
2:
3:
1 2 3456X X X X
X X X X 1 2 3 4 56
X X
#
1 2 3456
X X #
X X
X X X X #
X X
4RF Card Unlocking
Place the card close to keypad. If the card is correct, the LCD display shows the user information
and then unlock automatically.
5
USER INFORMATION
Operation
Change The Master Password
1
Input “0”and “#”, and then input the
master password to log in the system
a
Select “Admin” and confirm with “#”
cSelect “Password” and confirm with “#”
d
6
0#
+
***
Master
Select “Users” option
and confirm with “#”
b
#
+
Admin #
+
Password #
+
Select “Add Password”
and confirm with “#”
eInput the new password,
and then confirm with “#”
f
Add Password #
+
#
+
***
NEW
Input the new password again,
and then confirm with “#” to finish.
g
#
+
***
NEW
Once user finish the operation, please try to unlock
the lock to make sure the operation is successful.
Only fingerprint and password supported for
the master user.
The default master password is “01234-56789”;
There is only one master password available in
the lock, once the new master password is registered,
it will delete the old one.
The password can be 6 to 10 digits;
7
Add Master Fingerprint User
2
Input “0”and “#”, and then input the
master User to log in the system
a
Select “Admin” and confirm with “#”
cSelect “Fingerprint” and confirm with “#”
d
0#
+
Master
Select “Users” option
and confirm with “#”
b
#
+
Admin #
+
Fingerprint #
+
Select “Add fingerprint”
and confirm with “#”
ePlace the fingerprint on the sensor
in 3 times to finish.
f
Add Fingerprint #
+
X3
There is no limit capacity for the master fingerprint users, but the maximum user capacity is 300;
Once finish the operation, please try to unlock the lock to make sure the operation is successful.
Add Normal User
3
8
Input “0”and “#”, and then input the
master user to log in the system
a
Select “Add User” and confirm with “#”
cInput the name of the user group
and confirm with “#”
d
0#
+
Master
Select “Users” option
and confirm with “#”
b
#
+
Add User #
+
User 01 #
+
Select “fingerprint” and confirm with “#”
eSelect “Add fingerprint” and confirm with “#”
f
Fingerprint #
+
For Fingerprint
Add Fingerprint #
+
Place the fingerprint on the sensor
in 3 times to finish.
g
X3
9
For Password
Select “password” and confirm with “#”
eInput the password and confirm with “#”
f
Password #
+
#
+
Input the password again and confirm with “#” to finish
g
***
#
+
***
For Card
Select “card” and confirm with “#”
eSelect “add card” and confirm with “#”
f
Card #
+
Place the card on the card reader to finish.
g
Add Card #
+
The password can be 6 to 10 digits;
It is suggested to make a list to record the users in the lock.
You can register all users in the same user group or register the users in different user groups.
Once you finish the operation, please try to unlock the lock to make sure the operation
is successful.
Table des matières
Autres manuels Avent Security Serrure de porte
