Aunex AP Series Manuel utilisateur

AP Series 1 Channel Ampliers

Performance Class D Mono Amplier Series

Models: AP800.1D, AP1200.1D

Installation and Operation Manual

Please take time to thoroughly read through this manual to familiarize yourself with your new amplier.

This will ensure that your amplier will perform at its optimum capabilities.

Para obtener una copia de este manual en español, visite www.aunexusa.com y luego vaya a la página

del producto que necesita. Haga clic en la pestaña Soporte y descargue su manual en español.

AP1200.1D

AP800.1D

Congratulations and thank you for purchasing an Aunex AP Series

Amplier. This product has been engineered and manufactured

utilizing precision quality parts and craftsmanship. Improvements

in sound quality and system performance will be greatly enhanced

with the use of this amplier.

To ensure maximum performance we highly recommend you have

your new Aunex product installed by an Authorized Aunex Dealer.

Should you decide to install this product yourself, please make

sure to read this manual thoroughly to familiarize yourself with

the necessary installation requirements and tuning procedures.

Please read your warranty and retain a copy of your purchase

receipt and original carton should your amplier ever needs

to be serviced and warranted.

Visit our website for the latest information on all Aunex products

at: www.aunexusa.com. If you have any questions regarding this

product, please contact your Authorized Aunex Dealer for

assistance or call / email Aunex Technical Support Department at

(909) 589-5010 / [email protected].

Caution: Continuous exposure to sound pressure levels over 100dB

may cause permanent hearing loss. High powered audio systems can

produce sound pressure levels that can exceed over 150dB. Please limit

your exposure to continuous high listening volumes.

Feature Set of the AP Series Mono Ampliers

• Heavy Density Aluminum Extruded Heatsink

• 2 Layer PCB, SMD Technology

• Dierential Balanced RCA Inputs

• Fully Variable Crossover 30Hz – 500Hz @ 24dB/Octave Slope

• Fully Variable Infrasonic Filter 10Hz – 50Hz @ 24dB/Octave

• Boost Eq. 0 – 18dB @ 45Hz Center

• Fully Variable Phase 0 - 180⁰

• Auto-sensing in High Level Input Mode

o Remote Input Becomes Remote Output Trigger if

High level Input is used.

• Power and Protection Logo Illuminated Status Indicator

o Blue Indicates Amplier is powered On

o Red Indicates the Amplier is in Protection

• 4 Gauge Power & Ground Terminals

• 12 Gauge Speaker Output Terminals

• Advance Protection Circuit Monitoring: Short, Thermal,

Overload and Impedance

• Finish: Anodized with Texture Paint

What’s Included

• (1) AP Series Mono Class D Amplier

• (1) Remote Level Controller and Cable

• (1) High Level Speaker Plug

• (6) Self Tapping Screws; (4) for Amplier, (2) for Remote

• (2) Allen Wrenches

• (1) Instruction Manual

• (1) Sticker

Important Safety Considerations

• To prevent personal injury and damage to the unit, please read

the following instructions in this manual.

• This product is designed to use in vehicles with 12Volt,

negative-ground electrical systems.

• Install this product in a dry location away from your vehicles’

safety equipment (airbags, seat belt system, etc.). Water and

humidity may damage internal components.

• Use the included mounting accessories to secure this product

so that it does not come loose.

• Check before drilling to make sure you do not drill into any vital

vehicle system.

• Protect all system wiring from sharp metal edges.

• Do not disassemble or modify this unit; doing so will void your

manufacturer’s warranty.

Important Installation Precautions

Installation of mobile audio equipment requires experience.

Although this manual provides general installation procedures,

it will not show the exact installation method for your particular

vehicle.

If you do not have the required knowledge and experience,

we recommend that you have your equipment installed by an

Authorized Aunex Dealer.

• Turn o all stereo and other electrical devices before you begin.

• Disconnect the negative (-) lead from your vehicle’s battery to

avoid an electrical short. Reconnect the negative lead to your

battery once your installation is complete. So, in other words

the negative lead from our vehicle’s battery is the rst

connection you remove before starting your installation and

the last connect your make after you nish your installation.

• Check your mounting location to make sure there is sucient

room for your installation placement preference.

Mounting Placement

Choose a structurally sound location to mount your Aunex

amplier, making sure there are no items behind the area where

the screws will be driven.

For optimum sound quality, it is highly recommended that you

purchase Aunex wiring accessories as they are designed to give

your ampliers high-quality signal it needs to operate at peak

performance levels. Aunex provides a wide selection from RCA

cables and power wire to speaker wire and battery connectors.

Important Installation Precautions Continued

• Install this product in a dry location away from your vehicles’

safety equipment. Keeping the amplier dry and installed in a

well-ventilated area will help ensure many years of listening

enjoyment.

• When running power cables through sheet metal it is best to

use grommets and loom to properly insulate your cables from

metal edges.

• Avoid mounting the amplier with the top ns facing down as

this may increase the operating temperature of your amplier.

• If mounting underneath a seat, make sure that there is at least

1 inch (25mm) of space above the amplier to permit proper

cooling.

• Avoid mounting the ampliers on a subwoofer enclosure as

prolonged excessive vibration may damage your amplier.

Side Panel Layout

1 2

9 10 11 12 13

3 4 5 6 7 8

1. Remote Level Control: With the Remote Level Control plugged

to your amplier, you can now adjust the amount of output of

your subwoofer from the convenience of this controller.

Side Panel Layout Continued

2. High Level Input: These are your High-Level Speaker

Input that are used to connect your speaker outputs from your

headunit / source unit to your amplier. (Note only one type of

input is needed to send signal to your amplier, therefore

you only need to use either your Low Level or High-Level

input. Aunex does not recommend connecting both Inputs

simultaneously.)

3. Low Level RCA Inputs: These are your dierential

balanced inputs that are used to connect audio signal from your

headunit / source unit to your amplier. (Note only one type of

input is needed to send signal to your amplier, therefore

you only need to use either your Low Level or High-Level

input. Aunex does not recommend connecting both Inputs

simultaneously.)

4. Input Gain: Use these Input Gain Potentiometers to match the

output voltage of your headunit / source unit to the input circuit

of your amplier. These Input Gains are not a volume knob.

A simple method of setting your Input Gains is to turn your

headunit / source unit up to approximately ¾ volume. Then

slowly adjust your Input Gains on your ampliers clockwise until

you can hear distortion from your speakers or subwoofers. Then

turn the gains down (counterclockwise) till the distortion is no

longer heard.

Side Panel Layout Continued

5. Infrasonic Filter: This variable potentiometer will provide a roll

o point for lower frequencies (10Hz – 50Hz variable) that could

potentially damage your subwoofers from over-excursion. The

frequency setting for your Infrasonic Filter is to be set relative to

your speaker’s low-frequency capabilities along with enclosure

tuning. In a sealed box Aunex recommends setting the

Infrasonic Filter between 25Hz – 35Hz. In a ported enclosure

Aunex recommends setting the Infrasonic lter at ½ an Octave

below your tuned frequency.

For example, let say your ported enclosure is tuned at 40Hz.

Take ½ of 40Hz which is 20Hz (this is one octave lower). Now

take another half o 20Hz which is then 10Hz (this is half an

octave lower). Now take 10Hz from 40Hz which is 30Hz and

where you should set your Infrasonic Filter.

6. Boost Eq: Your AP Series ampliers incorporates a Boost Eq.

circuit that can increase output 0-18dB centered at 45Hz. Note

if you turn up the Boost Eq, you will need to readjust the Input

Gains to avoid clipping the output signal.

7. Phase Switch: Depending on the absolute phase of your main

speakers and amplier and the distances of the subwoofer and

the main speaker from the main listening position, the bass in

the crossover region maybe smoother if you reverse the

subwoofer’s phase. Try both settings to determine which

polarity produces the best overall bass performance in your

system. Typically, though, phase is left at the 0⁰ for most

installation.

8. Low Pass (LP) Filter Frequency Filter: This potentiometer

allows you to adjust the crossover frequency from 30Hz – 500Hz.

9. Speaker Outputs: Your AC amplier speaker outputs are

designed to accept 16 AWG to 12 AWG wire. Turn the set screws

on this terminal counterclockwise to loosen the screws using

the supplied Hex wrench. Strip the PVC jacket from your speaker

wire ½ inch (12mm). Then insert the bare wire into the terminal

block so that no bare speaker wire is exposed. Then tighten the

set screw by turning it clockwise.

Loading your amplier below the recommended

impedance rating found on page 14 is not recommended

and may cause your amplier to enter into protection mode

and may void your warranty.

For maximum current ow, Aunex recommends that you tin

your speaker wire before connecting it to the speaker output

terminals. In addition, Aunex recommends using high

quality 100% OFC (Oxygen Free Copper) or Tinned 100% OFC

speaker wire. This will ensure that your speaker / subwoofer

receives maximum output from your amplier.

10. Fuse Holder: This is your fuse block. Should there be a short in

your system or if your amplier is being overdriven, these fuse(s)

will typically burn to prevent damage to your amplier. If it is

required to replace your fuse(s), use the same fuse rating that

comes with your amplier. Using a higher fuse may damage

your amplier and will void your warranty.

11. +12Volt Positive Terminal: The +12Volt positive terminal is

designed to accept up to 4 AWG wire. Use the supplied fuse

block and make your +12Volt connection directly to the positive

battery post. The Fuse should be installed within 18” (457mm)

of the battery. This fuse is vital to protecting the vehicle and

amplifier from a dead short. Turn the set screws on

this terminal counterclockwise to loosen the screw using the

supplied Hex wrench. Strip the PVC jacket from your power wire

½ inch (12mm). Then insert the bare wire into the terminal block

so that no bare power wire is exposed. Then tighten the set

screw by turning it clockwise.

Side Panel Layout Continued

For maximum current ow, Aunex recommends that you tin

your power wire before connecting it to the +12Volt terminal. In

addition, Aunex recommends using high quality 100% OFC

(Oxygen Free Copper) or Tinned 100% OFC speaker wire. This

will ensure that your speaker / subwoofer receives maximum

output from your amplier.

12. Remote Input Terminal: This terminal must be connected to

a switched +12Volt source. If the source unit does not have a

remote Turn on lead, then a switched +12 supply should be

used such as the ACC +12Volt. Run an 18-gauge wire from the

Remote Turn-On Lead from your headunit / source unit to this

terminal.

If you are using the High-Level Speaker Outputs connection

to the ampliers’ RCA inputs, you do not need to connect

a remote input to your amplier. Your amplier will

automatically detect the speaker signal and will turn on

your amplier via its DC Oset circuit. In addition, the

remote input terminal then becomes a remote output

trigger which can be used to turn on another amplier or

processor that requires a +12volt remote connection.

13. Ground: The ground terminal is designed to accept up to 4

AWG wire. Make your ground connection directly to the chassis

of the vehicle as close to the amplier as possible. Make sure

this connection is made with the same gauge wire as used for

your +12Volt connection. Ensure that all dirt, grease and paint is

removed from your chassis ground point prior to attaching the

ground wire. Aunex recommends when making your chassis

ground to use a star washer which will help prevent your

ground bolt from loosening.

Side Panel Layout Continued

Autres manuels pour AP Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Aunex Amplificateur

Aunex

Aunex AC Series Manuel utilisateur

Aunex

Aunex AM Series Manuel utilisateur

Aunex

Aunex AC 5 Series Manuel utilisateur

Aunex

Aunex AC Series Manuel utilisateur

Aunex

Aunex AMX Series Manuel utilisateur

Aunex

Aunex AP Series Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur