Audix M55WD Guide de dépannage
INSTALLATION &
OPERATING GUIDE
DANTE®
–AES67
MICROPHONE INTERFACE
M55WDM55WD
The Audix Dante–AES67 microphone systems are the industry’s first integrated
solution to eliminate multiple connectors by providing audio, LED status and logic
functionality with a single RJ45 cable connection. This design reduces conventional
wiring and installation time by 90% and eliminates wiring errors. Once the connection
is made to the network via the Audix DN4 interface, the Audix microphone(s) will be
automatically recognized and populated by model number in the Audix DSP plugin.
IN THE BOX
• M55D microphone
• Knurled fastener
• Seismic / restraint cable
• Spec sheet
• Installation guide
THE AUDIX INTEGRATED MICROPHONE SYSTEM | DANTE–AES67
SWITCH
DSP
AUDIX DN4
M55D
M55D
M55D
M55D
M55D
FIGURE 6
Connect the DN4/DN43 Dante-AES67
interface to a PoE switch (see DN4/
DN43 guide).
FIGURE 1
Drill a 3/4” (19mm) hole in the ceiling
tile. Place cylinder on top of hole after
removing the lid, and insert M55D collar
through the hole. Fasten nut.
FIGURE 3
Insert category cable into RJ45
receptacle of M55D and DN4/DN43
mic input. Use Audix Cat7 or shielded
category cable.
FIGURE 2
Plug in 7 pin microphone connector
into mating receptacle as shown above.
Refasten lid.
FIGURE 4
Seismic cable installation; Insert cable
through the top of cable stay barrel
pulling excess cable until taut. Place
cable eyelet under brass screw and
fasten.
FIGURE 5
Connect up to four microphones to the
Audix DN4 or one M3 and one single-
channel microphone to the Audix DN43
interface.
INSTALLATION
CABLE RELEASE PIN
CABLE RELEASE PIN
CABLE STAY
CABLE STAY
BARREL
CABLE
M55D v1.2
© 2019 Audix Corporation. Audix is a registered trademark of the Audix
corporation. Specifications subject to change without notice. For service
and warranty information, visit AudixUSA.com/service or call 800.966.8261
FIGURE 10
1. Mic ID will show model number
by channel
2. Starting “state” LED color can be
selected
3. Gain control
4. High pass filter
5. Low pass filter
6. See Q-SYS™ designer asset manager
Audix help file for detailed instructions
FIGURE 9
1. Open Dante controller to confirm
discovery on your network
2. If using Q-SYS™ DSP open Designer
Asset Manager and Dowload Audix
Plugin
3. Open Audix Plugin
4. See Figure 10 for Q-SYS™ control and
LED functions
5. For DSP’s currently without Audix
plugin, audio channels can be routed
through the Dante controller.
6. See tech support at audixusa.com for
updated API / Plugin information
FIGURE 7
For desired microphone coverage
and position, loosen M55D knurled
nut (aprox. half-turn), adjust cable
length, and retighten nut.
OPERATION OVERVIEW
FINAL ADJUSTMENT
M55
Autres manuels Audix Microphone
Audix
Audix i5 Manuel utilisateur
Audix
Audix M55 Manuel utilisateur
Audix
Audix USB12 Manuel utilisateur
Audix
Audix CX112B Manuel utilisateur
Audix
Audix OM6 Manuel utilisateur
Audix
Audix UEM81C Manuel utilisateur
Audix
Audix M44 Manuel utilisateur
Audix
Audix ADX10 Manuel utilisateur
Audix
Audix M1280B Manuel utilisateur
Audix
Audix OM2 Guide d'installation
Audix
Audix M70 Manuel utilisateur
Audix
Audix M40 Manuel utilisateur
Audix
Audix Micros M1280 Guide d'installation
Audix
Audix HT2 Manuel utilisateur
Audix
Audix ADX20i Manuel utilisateur
Audix
Audix M3 Manuel utilisateur
Audix
Audix L5 Manuel utilisateur
Audix
Audix MGN Series Manuel utilisateur
Audix
Audix M40 Manuel utilisateur
Audix
Audix VX5 Manuel utilisateur
