Audix M70WD Guide de dépannage
M70WD
INSTALLATION &
OPERATING GUIDE
The Audix Dante–AES67 microphone systems are the industry’s first integrated
solution to eliminate multiple connectors by providing audio, LED status and logic
functionality with a single RJ45 cable connection. This design reduces conventional
wiring and installation time by 90% and eliminates wiring errors. Once the connection
is made to the network via the Audix DN4 interface, the Audix microphone(s) will be
automatically recognized and populated by model number in the Audix DSP plugin.
IN THE BOX
• M70WD microphone
• Knurled fastener
• Seismic / restraint cable
• Spec sheet
• Installation guide
THE AUDIX INTEGRATED MICROPHONE SYSTEM | DANTE–AES67
SWITCH
DSP
AUDIX DN4
M55WD
FIGURE 6
Connect the DN4 Dante interface to a
PoE switch (see DN4 guide).
FIGURE 1
Determine the microphone placement,
drill a 2 inch (51mm) hole in the ceiling
tile or mounting surface.
FIGURE 3
For seismic cable installation, wrap the
cable through beam, eyebolt or hanger
and cable stay barrel (see figure 4).
Remove M70WD placement screw and
place eyelet over hole and tighten screw.
FIGURE 2
Remove the knurled ring from the
module, insert the module through
the hole and reattach the knurled ring.
Connect RJ45 cable to the M70 module.
FIGURE 4
Cable Stay Operation
FIGURE 5
Connect up to 4 microphones via Cat5 -
7 to the Audix DN4 interface.
INSTALLATION
CABLE RELEASE PIN
CABLE STAY
BARREL
CABLE
M70WD Guide v1.1
© 2019 Audix Corporation. Audix is a registered trademark of the Audix
corporation. Specifications subject to change without notice. For service
and warranty information, visit AudixUSA.com/service or call 800.966.8261
FIGURE 10
1. Mic ID will show model number
by channel
2. Starting “state” LED color can be
selected
3. Gain control
4. High pass filter
5. Low pass filter
6. See Q-SYS™ designer asset manager
Audix help file for detailed instructions
FIGURE 9
1. Open Dante controller to confirm
discovery on your network
2. If using Q-SYS™ DSP open Designer
Asset Manager and Dowload Audix
Plugin
3. Open Audix Plugin
4. See Figure 10 for Q-SYS™ control and
LED functions
5. For DSP’s currently without Audix
plugin, audio channels can be routed
through the Dante controller.
6. See tech support at audixusa.com for
updated API / Plugin information
FIGURE 8
Reinstall grille – do not overtighten.
FIGURE 7
Remove grille by turning counterclockwise.
Adjust the microphone to point to the
desired direction or coverage area.
OPERATION OVERVIEW
FINAL ADJUSTMENTS
Autres manuels Audix Microphone
Audix
Audix i5 Manuel utilisateur
Audix
Audix USB12 Manuel utilisateur
Audix
Audix VX5 Manuel utilisateur
Audix
Audix M40 Manuel utilisateur
Audix
Audix i5 Manuel utilisateur
Audix
Audix OM2 Guide d'installation
Audix
Audix ADX20i Manuel utilisateur
Audix
Audix CX-112 Manuel utilisateur
Audix
Audix M70 Manuel utilisateur
Audix
Audix M40 Manuel utilisateur
Audix
Audix M55WD Guide de dépannage
Audix
Audix HT2 Manuel utilisateur
Audix
Audix M44 Manuel utilisateur
Audix
Audix L5 Manuel utilisateur
Audix
Audix M70 Manuel utilisateur
Audix
Audix M3-W Manuel utilisateur
Audix
Audix M70 Manuel utilisateur
Audix
Audix UEM81C Manuel utilisateur
Audix
Audix M70WD Guide de dépannage
Audix
Audix M3 Manuel utilisateur
