Audio Technica ES954 Manuel utilisateur

User Manual

Hanging Microphone Array

ES954

Features

•Ideal, cost-effective solution for huddle rooms, conference rooms and

other meeting spaces.

•Quad-capsule steerable microphone array designed for use with the

ATDM series DIGITAL SMARTMIXER™ and other compatible mixers.

•When controlled by a compatible mixer, provides 360° coverage from

a potentially limitless number (bound by mixer channel count) of virtual

hypercardioid or cardioid pickups that can be steered in 30° increments

to clearly capture every person speaking in a room by using original

synthetic technology (PAT.).

•Mixer-controlled tilt function provides a vertical steering option to

accommodate ceilings of different heights.

•Includes UL 2043 plenum-rated AT8554 Ceiling Mount with RJ45

connectors and push-type wire terminals for simple, secure installation

with seismic cable to secure to a drop ceiling grid.

•Integral, logic-controlled red/green LED ring provides clear indication of

mute status.

•High-output design with low self-noise delivers strong, natural-sounding

vocal reproduction.

•Low-reflective white finish matches ceiling tiles in most environments

•Includes two 46 cm (18") breakout cables: RJ45 (female) to three 3-pin

Euroblock connector (female), RJ45 (female) to 3-pin Euroblock connector

(female) and unterminated LED conductors.

•The 3.0 m (9.8') microphone cable is secured at the celing tile with a

locking grommet for quick microphone height adjustment.

•Audio-Technica's proprietary RFI-shielding technology thoroughly

eliminates radio frequency interference (RFI).

•Requires 11 V to 52 V DC phantom power.

Trademarks

• SMARTMIXERTM is a trademark or registered trademark of Audio-Technica

Corporation.

Introduction

Thank you for purchasing this product. Before using the product, read through the

user manual to ensure that you will use the product correctly.

Safety precautions

Although this product was designed to be used safely, failing to use it correctly may

result in an accident. To ensure safety, observe all warnings and cautions while

using the product.

Cautions for the product

• Do not subject the product to strong impact to avoid malfunction.

• Do not disassemble, modify or attempt to repair the product.

• Do not handle the product with wet hands to avoid electric shock or injury.

• Do not store the product under direct sunlight, near heating devices or in a hot,

humid or dusty place.

• Do not install the product close to air conditioner or lighting apparatus to prevent

malfunction.

• Do not pull on the product with excessive force nor hang on it after it is installed.

Connection

LED

Connect the output terminals of the microphone to a device that has a microphone

input (balanced input) compatible with a phantom power supply.

The output connector is a Euroblock connector with polarity as shown in the figure

below.

Use STP cables to connect from the ceiling mount RJ45 jacks to breakout cables.

Output terminals

The product requires 11V to 52V DC

phantom power for operation.

Wiring Chart

RJ45 connector

pin number Function RJ45 breakout cable

wire color

OUT A

1 MIC2 L(+) BROWN

2 MIC2 L(-) ORANGE

3 MIC3 R(+) GREEN

4 MIC1 O(-) WHITE

5 MIC1 O(+) RED

6 MIC3 R(-) BLUE

7 GND BLACK

8 GND BLACK

OUT B

1 BLANK -

2 BLANK -

3 LED GREEN GREEN

4 MIC4 Z(-) WHITE

5 MIC4 Z(+) RED

6 LED RED BLUE

7 GND BLACK

8 GND BLACK

• Output from the microphone is low impedance (Lo-Z) balanced. The signal

appears across the pair of each output Euroblock connectors on the RJ45

breakout cables. Audio ground is the shield connection. Output is phased so

that positive acoustic pressure produces positive voltage on the left side of each

Euroblock connector.

• MIC1 is “O” (omnidirectional), MIC2 is “L” (bidirectional (figure-of-eight))

positioned horizontally at 240°, MIC3 is “R” (bidirectional (figure-of-eight))

positioned horizontally at 120°, and MIC4 is “Z” (bidirectional (figure-of-eight))

positioned vertically.

Pin assignment

MIC 1

O +

O -

GND

MIC 2

L +

L -

GND

MIC 3

R +

R -

GND

MIC 4

Z +

Z -

GND

LED Control

LED GREEN

LED RED

GND

LED

STP cable

(MIC1-MIC3)

Ceiling mount (AT8554)

RJ45

Breakout cable-A

MIC 3MIC 2MIC 1 LED ControlMIC 4

RJ45

Breakout cable-B

ATDM series DIGITAL SMARTMIXERTM

3rd-party mixer

STP cable

(MIC4 / LED Control)

LED control

• To control the LED indicator ring, connect the LED Control terminals of the RJ45 breakout cable to the GPIO port of the automatic mixer or other logic device.

• When using the product with a mixer with no GPIO terminal, the LED ring can be kept permanently lit by connecting the black (BK) or violet (VT) wire to the GND terminal.

When the black wire is shorted, the LED ring will be green. When the violet wire is shorted, the LED ring will be red.

Parts, name and installation

Cable

Retaining nut

Backplate

Ceiling mount

(AT8554)

RJ45 connector

Latch

Ceiling tile

Isolator

Threaded bushing

Locking grommet

Microphone

Isolator

(receiver)

Adjust the length

of cable.

Turn the locking

grommet to secure

it.

Seismic cable

Cable tie

Terminal

connector

Release bar

Ceiling

Make sure to attach the included seismic cable to the

ceiling to prevent the ceiling mount from falling.

Using the cable tie, fix the remaining cable to the inside of

the ceiling mount to prevent the microphone from falling.

90°

0°

(Front)

180°

(Rear)

270°

Notices

• When installing the product, a hole must be cut into the ceiling tile so the ceiling mount can be fixed in place. Remove the ceiling tile first if possible.

• To mount the threaded bushing in a ceiling tile without the isolators:

20.5 mm (0.81") diameter hole is required and the ceiling tile can be up to 22 mm (0.87") thick.

• To mount the threaded bushing with the isolators:

23.5 mm (0.93") hole is required and the ceiling tile can be up to 25 mm (0.98") thick. Place the isolators on either side of the hole to achieve mechanical isolation from the

mounting surface.

Installation

1. Remove the backplate of the ceiling mount and place it against the back of the ceiling tile, allowing the threaded bushing to pass through.

2. Once in place, thread the retaining nut onto the threaded bushing, securing the ceiling mount to the ceiling tile.

3. Connect the microphone cable to the terminal connector on the ceiling mount by pressing down the orange tabs on the terminal strip.

4. Once all connections are made, fix the remaining cable to the inside of the ceiling mount using the cable tie.

5. Adjust the cable to desired microphone height by either feeding or pulling the cable through the ceiling mount.

6. Once the microphone is in the desired position, gently turn the locking grommet clockwise to secure. (Do not over tighten and pull the cable strongly).

7. Coil the excess cable into the ceiling mount and replace the backplate.

Recommended position

Change the height and tilt position according to the environment in which you use

the product.

MIC position

Tilt

Minimum

Height Typical Height Maximum

Height

Tilt up 1.2 m (4’) 1.75 m (5.75’) 2.3 m (7.5’)

Tilt down 1.7 m (5.6’) 2.2 m (7.2’) 2.7 m (9’)

Coverage examples

• For 360° coverage, create four hypercardioid (normal) virtual polar patterns at the 0°, 90°, 180°, 270°

positions. This setting is ideal for providing omnidirectional coverage of four people around a round

table (see Figure. A).

• For 300° coverage, create three cardioid (wide) virtual polar patterns at the 0°, 90°, 180° positions.

This setting is ideal for covering three people at the end of a rectangular table (see Figure. B).

• For installation of two or more units, we recommend that you install them at a distance of at least

1.7m (5.6’) (for hypercardioid (normal)) so that the coverage ranges of the microphones do not

overlap (see Figure. C).

Figure A Figure B

Figure C

1.7 m (5.6')

1.2 m

(4’)

1.75 m

(5.75’)

2.3 m

(7.5’)

Max. 3 m (10')

1.7 m

(5.6’)

2.2 m

(7.2’)

2.7 m

(9’)

Max. 3 m (10')

Using the product with the ATDM series DIGITAL SMARTMIXER™

Use the latest firmware for the ATDM series DIGITAL SMARTMIXERTM.

1. Connect Mic 1-4 of the product to input 1-4 on the ATDM series DIGITAL

SMARTMIXERTM. Launch Web Remote, select “Administrator”, and log in.

• When using two units of the product with ATDM-1012/ATDM-1012DAN at the

same time, connect INPUT 1 to 4 and INPUT 6 to 9.

2. Click the icon ( ) on the top right of the screen then select "System Settings" >

"Audio". Activate "Virtual Mic Mode". This automatically sets the input type of input

channels 1 to 4 of the ATDM series DIGITAL SMARTMIXERTM to "Virtual Mic".

• For input channels other than "Virtual Mic" which is automatically selected by

default, you can also select "Virtual Mic" and make the same settings.

About Operator Access / Operator Page in Settings &

Maintenance

When "Virtual Mic Mode" and "Array Mic Switch" are enabled, an array mic mute

ON/OFF button appears on the operator page. The microphone can be muted on the

operator page.

• This setting is not saved on the device, so rebooting the ATDM series DIGITAL

SMARTMIXERTM restores it to its default position.

Administrator page's input tab on the main screen

1. In the Input tab, check that the input type for input channels 1-4 is set to "Virtual

Mic".

• For input channels other than "Virtual Mic", which is automatically selected by

default, you can also select "Virtual Mic" and make the same settings.

2. Adjust the gain to the required level (a).

• Setting the input gain on one channel will simultaneously change it on all four

channels. Low cut, EQ, Smart Mix and output bus assign can individually be

assigned for each channel.

3. Clicking "Pattern" of the Virtual Mic box (b) opens the settings tab for the directivity

pattern. These can be adjusted between “Normal” (hypercardioid) , “Wide” (cardioid)

and "Omni".

4. Clicking the blue button around the circle sets the orientation of each Virtual Mic.

5. Adjust the Virtual Mic direction towards the talker to be picked up.

• The Audio-Technica logo is located on the front of the microphone. The

microphone must be oriented correctly to operate properly.

6. Using the “Tilt” function, you can adjust the directivity on the vertical plane to adjust

the angle depending on whether the talker is sitting or standing.

7. Adjust the individual volume of each Virtual Mic using the Volume Fader.

(a) (b)

Using with other compatible mixer

When connecting and using the product with a mixer other than the ATDM series DIGITAL SMARTMIXERTM, directivity can be controlled by adjusting the output of each

channel according to the following mixing matrix.

Mixing matrix Normal Wide

Tilt up

Tilt down

Polar pattern

Directivity

direction

O L R Z

φLevel φLevel φLevel φLevel

0° + -4dB - 0dB - 0dB -∞

30° + -4dB - +1.2dB - -4.8dB -∞

60° + -4dB - 0dB -∞ -∞

90° + -4dB - -4.8dB + -4.8dB -∞

120° + -4dB -∞ + 0dB -∞

150° + -4dB + -4.8dB + +1.2dB -∞

180° + -4dB + 0dB + 0dB -∞

210° + -4dB + +1.2dB + -4.8dB -∞

240° + -4dB + 0dB -∞ -∞

270° + -4dB + -4.8dB - -4.8dB -∞

300° + -4dB -∞ - 0dB -∞

330° + -4dB - -4.8dB - +1.2dB -∞

Directivity

direction

O L R Z

φLevel φLevel φLevel φLevel

0° + 0dB - 0dB - 0dB -∞

30° + 0dB - +1.2dB - -4.8dB -∞

60° + 0dB - 0dB -∞ -∞

90° + 0dB - -4.8dB + -4.8dB -∞

120° + 0dB -∞ + 0dB -∞

150° + 0dB + -4.8dB + +1.2dB -∞

180° + 0dB + 0dB + 0dB -∞

210° + 0dB + +1.2dB + -4.8dB -∞

240° + 0dB + 0dB -∞ -∞

270° + 0dB + -4.8dB - -4.8dB -∞

300° + 0dB -∞ - 0dB -∞

330° + 0dB - -4.8dB - +1.2dB -∞

Directivity

direction

O L R Z

φLevel φLevel φLevel φLevel

0° + -4dB - -3dB - -3dB + -3dB

30° + -4dB - -1.8dB - -7.8dB + -3dB

60° + -4dB - -3dB -∞ + -3dB

90° + -4dB - -7.8dB + -7.8dB + -3dB

120° + -4dB -∞ + -3dB + -3dB

150° + -4dB + -7.8dB + -1.8dB + -3dB

180° + -4dB + -3dB + -3dB + -3dB

210° + -4dB + -1.8dB + -7.8dB + -3dB

240° + -4dB + -3dB -∞ + -3dB

270° + -4dB + -7.8dB - -7.8dB + -3dB

300° + -4dB -∞ - -3dB + -3dB

330° + -4dB - -7.8dB - -1.8dB + -3dB

Directivity

direction

O L R Z

φLevel φLevel φLevel φLevel

0° + 0dB - -3dB - -3dB + -3dB

30° + 0dB - -1.8dB - -7.8dB + -3dB

60° + 0dB - -3dB -∞ + -3dB

90° + 0dB - -7.8dB + -7.8dB + -3dB

120° + 0dB -∞ + -3dB + -3dB

150° + 0dB + -7.8dB + -1.8dB + -3dB

180° + 0dB + -3dB + -3dB + -3dB

210° + 0dB + -1.8dB + -7.8dB + -3dB

240° + 0dB + -3dB -∞ + -3dB

270° + 0dB + -7.8dB - -7.8dB + -3dB

300° + 0dB -∞ - -3dB + -3dB

330° + 0dB - -7.8dB - -1.8dB + -3dB

90°

120°

150°

180°

210°

240°

270°

300°

330°

60°

30°

0°

LEGEND 1kHz

SCALE IS 5 DECIBELS PER DIVISION

90°

120°

150°

180°

210°

240°

270°

300°

330°

60°

30°

0°

LEGEND 1kHz

SCALE IS 5 DECIBELS PER DIVISION

Specifications

Elements Fixed-charge back plate, permanently polarized condenser

Polar pattern Omnidirectional (O) / Bidirectional (figure-of-eight) (L/R/Z)

Frequency response 20 to 16,000 Hz

Open circuit sensitivity O/L/R: -36 dB (15.85 mV) (0 dB=1 V/Pa,1 kHz)

Z: –38.5 dB (11.9 mV) (0 dB=1 V/Pa,1 kHz)

Impedance 100 ohms

Maximum input sound level O/L/R: 132.5 dB SPL (1 kHz THD1%)

Z: 135 dB SPL (1 kHz THD1%)

Signal-to-noise ratio O/L/R: 66.5 dB (1 kHz at 1 Pa, A-weighted)

Z: 64 dB (1 kHz at 1 Pa, A-weighted)

Phantom power

requirements 11 - 52 V DC, 23.2 mA (all channels total)

Weight Microphone: 160 g (5.6 oz)

Ceiling mount (AT8554): 460 g (16.2 oz)

Plenum rating UL 2043

Dimensions (Microphone) Maximum body diameter: 61.6 mm (2.4”)

Height: 111.8 mm (4.4”)

(Ceiling mount (AT8554)) 106 mm (4.2”) × 106 mm (4.2”) × 45.6 mm (1.8”) (W × D × H)

Output connector Euroblock connector

Accessories Ceiling mount (AT8554), RJ45 breakout cable × 2,

Retaining nut, Seismic cable, Isolator, Cable tie

• 1 Pascal = 10 dynes/cm2= 10 microbars = 94 dB SPL

For product improvement, the product is subject to modification without notice.

Polar pattern / Frequency response

Omnidirectional (O)

Bidirectional

(figure-of-eight) (L/R/Z)

90°

120°

150°

180°

210°

240°

270°

300°

330°

60°

30°

0°

LEGEND 1kHz

SCALE IS 5 DECIBELS PER DIVISION

10dB

5020

20k

(Hz)

10k5k2k1k500200100

Response in dB

LEGEND

0°, 50 cm

90°

120°

150°

180°

210°

240°

270°

300°

330°

60°

30°

0°

LEGEND 1kHz

SCALE IS 5 DECIBELS PER DIVISION

10dB

5020

20k

(Hz)

10k5k2k1k500200100

Response in dB

LEGEND

0°, 50 cm

142419271-02-01 ver.1 2022.11.15

Dimensions

φ61.6

111.8

106

102

10645.6

Audio-Technica Corporation

2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan

Global Support Contact: www.at-globalsupport.com

Made in Japan

Frequency in Hertz

(Unit: mm)

Autres manuels pour ES954

Table des matières

Autres manuels Audio Technica Système de microphone

Audio Technica

Audio Technica PRO 227 Manuel du propriétaire

Audio Technica

Audio Technica Artist Elite 4000 Series Mode d'emploi

Audio Technica

Audio Technica 2000 Series Manuel du propriétaire

Audio Technica

Audio Technica SpectraPulse mtu201 Instruction manuelle

Audio Technica

Audio Technica ATW-DA49 Manuel du propriétaire

Audio Technica

Audio Technica AT-ONE Manuel du propriétaire

Audio Technica

Audio Technica FREEWAY ATW-701 Manuel du propriétaire

Audio Technica

Audio Technica 3000 Series Mode d'emploi

Audio Technica

Audio Technica 1800 Series Manuel du propriétaire

Audio Technica

Audio Technica ATW-49SP Manuel du propriétaire

Audio Technica

Audio Technica PRO 88W Manuel utilisateur

Audio Technica

Audio Technica 1800 Series Instruction manuelle

Audio Technica

Audio Technica ATW-A10 Manuel du propriétaire

Audio Technica

Audio Technica ATW-A20 Manuel du propriétaire

Audio Technica

Audio Technica 700 Series Mode d'emploi

Audio Technica

Audio Technica ATW-7373 Manuel du propriétaire

Audio Technica

Audio Technica UniPak ATW-1661 Manuel du propriétaire

Audio Technica

Audio Technica ATW-49CB Manuel du propriétaire

Audio Technica

Audio Technica ATW-2120 Manuel utilisateur

Audio Technica

Audio Technica 3000 Series Manuel utilisateur

Audio Technica

Audio Technica ATW-1031 Manuel du propriétaire

Audio Technica

Audio Technica ATW-2110 Manuel du propriétaire

Audio Technica

Audio Technica ATW-1127 Manuel du propriétaire

Audio Technica

Audio Technica AEW-4100 Series Manuel d'utilisation

Manuels Système de microphone populaires d'autres marques

Paso

Paso R824 Manuel utilisateur

Naxa

Naxa NAM-982 Manuel utilisateur

Motorola

Motorola PMNN4461 Manuel utilisateur

Xvive

Xvive U3 Manuel utilisateur

Tekon

Tekon DUOS Manuel utilisateur

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manuel utilisateur

Devine

Devine WMD-IE Manuel utilisateur

LG LF-D7150 Manuel utilisateur

GE S768DAV Manuel utilisateur

LD U305 HBH 2 Manuel utilisateur

Chainway

Chainway URA8 Manuel utilisateur

ORATOR

ORATOR D860TD Manuel utilisateur

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuel utilisateur

Alpha Technologies

Alpha Technologies RBMS Manuel utilisateur

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manuel utilisateur

Shure

Shure UA844 Manuel utilisateur

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuel utilisateur

Pyle

Pyle PDWM5000 Manuel utilisateur