AUDAC WS500 Manuel utilisateur

PROFESSIONAL AUDIO EQUIPMENT

Design Wall Loudspeaker WS500

Installation Guide

DesignWallLoudspeaker

WS500

AUDAC

Installation procedure

1) Before mounting the loudspeaker, the front grill should be removed

to make the mounting holes accessible. The best method for

removing the front grill is to push the lower side of the front grill up

with your thumbs. The grill should easily slide up, without

performing large forces.

2) When the lower side of the grill is pushed upwards, the attachment

tabs on the bottom of the front grill should slide out of the

mounting slots. The lower side of the front grill can be popped

out. After this, the upper side can also be detached easily and the grill

can be removed.

3) After the grill is removed, the two mounting holes are visible. One

mounting hole is provided on the upper side, while the second mounting

hole is provided on the lower side of the loudspeaker.

4) Before mounting the loudspeaker, make sure that the speaker can be mounted on a safe location and

the mounting location is solid enough to support the weight of the loudspeaker.

5) Connect the terminals of the loudspeaker. More information about the connections can be found in

the “Connections” section of this manual.

6) After the connections are made, a screw should be provided on the desired mounting location of the

upper mounting hole. Once this screw is provided, the upper mounting hole should glide over the

mounting screw. The loudspeaker is now hanging on one single screw.

7) Now the second mounting hole can be drawn. It is located 25.5 cm lower than the first mounting hole.

8) When both mounting points are provided, both screws can be inserted and tightened.

9) When the loudspeaker is suspended with both mounting points and the connections are made, the

front grill can be placed again. This can be done by sliding the upper mounting tabs of the front grill

into the provided slots, and afterwards sliding the lower mounting tabs into the provided slots.

Connections

To avoid electric shocks during installation, always switch of the amplifier power when connecting

loudspeakers.

On the rear side of the loudspeaker three connection terminals are provided.

By means of selecting the appropriate connection terminals, the desired line transformer power tapping

can be set, to be used in 100V public address applications.

COM 10 Watt 5 Watt

Those connection terminals should be connected to the amplifier output. The COM connection

terminal should always be connected with the COM output terminal of the Amplifier. When the

loudspeaker should play at full power, the positive terminal of the amplifier output should be connected

to the 10 Watt terminal (Red). When only half the power is needed, the positive terminal of the

amplifier output should be connected to the 5 Watt terminal (White)

Connections for 100 Volt use:

COM Black

10 Watt / 1000 Ohm Red

5 Watt / 500 Ohm White

When the loudspeaker is connected to 70.7V facilities, the power indicated in the table above will be

reduced to half the power, and when connected to 50V facilities, the power will be reduced to a quarter.

When the desired power tap is selected and connected, the loudspeaker is ready to be used.

Technical Specifications

Max Power 20 Watt

RMS Power 10 Watt

Line Transformer Power taps 10 Watt 1000 Ohm

5 Watt 500 Ohm

Line Voltage 100 V

Driver impedance 8 Ohm

Sensitivity 1W / 1m 92 ± 3 dB

SPL Max W / 1m 102 dB

Frequency response 150 Hz – 15 kHz

Material ABS

Weight 1.62 Kg

Speaker 6.5”

Colour White

Material ABS

Table des matières

Autres manuels AUDAC Intervenants

AUDAC

AUDAC XENO 8 Mode d’emploi

AUDAC

AUDAC VEXO110A Manuel utilisateur

AUDAC

AUDAC SPRING-FIT CENA306 Manuel utilisateur

AUDAC

AUDAC LINO4 Mode d’emploi

AUDAC

AUDAC ATEO2S Mode d’emploi

AUDAC

AUDAC ATEO2D Mode d’emploi

AUDAC

AUDAC ARES5A Manuel utilisateur

AUDAC

AUDAC SPRING-FIT CENA Series Manuel utilisateur

AUDAC

AUDAC WX802/W Instructions d'installation et d'utilisation

AUDAC

AUDAC AWP06 Instructions d'installation et d'utilisation

AUDAC

AUDAC ATEO M Series Manuel utilisateur

AUDAC

AUDAC VEXO112A Manuel utilisateur

AUDAC

AUDAC SPRING-FIT CENA812 Manuel utilisateur

AUDAC

AUDAC WX Series Mode d’emploi

AUDAC

AUDAC SPRING-FIT CENA506 Manuel utilisateur

AUDAC

AUDAC VEXO1A Series Manuel utilisateur

AUDAC

AUDAC BASO Series Mode d’emploi

AUDAC

AUDAC Ateo 6 Mode d’emploi

AUDAC

AUDAC CELO6 Mode d’emploi

AUDAC

AUDAC BASO10/B Mode d’emploi

AUDAC

AUDAC PX108 Instructions d'installation et d'utilisation

AUDAC

AUDAC WX802 Instructions d'installation et d'utilisation

AUDAC

AUDAC VEXO110 Manuel utilisateur

AUDAC

AUDAC VIRO5 Manuel utilisateur

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur