Atmel AT89EVK-01 Manuel utilisateur
AT89EVK-01 User Guide 1-3
4325C–SCR–09/04
Section 1
Introduction
This document describes the AT89EVK-01 evaluation kit dedicated to the AT83C24
Smart Card Reader Interface IC. This board is designed to allow an easy evaluation of
the AT83C24 on an application using the TDA8004.
This board can be connected on the TDA8004 footprint.
1.1 Features The AT89EVK-01 provides the following features:
Possibility to replace the TDA8004 (or TDA8024) with the AT89EVK-01 board . The
AT89EVK-01 board is soldered on the TDA8004 footprint.
The AT83C24 registers are programmed with the TWI link (SDA,SCL). The
T89C5121 microcontroller sends the TWI commands to configure the AT83C24
registers.
The configuration software is stored in T89C5121 Flash memory. The program can be
reloaded by using FLIP / BatchISP (In-System Programming tool) and an RS-232
adaptor board (CEIBO for example).
Hardware configuration allowed with switches and solder pads.
The program can be modified and reloaded with Batchisp (see 2.2.2)
Introduction
1-4 AT89EVK-01 User Guide
4325C–SCR–09/04
AT89EVK-01 User Guide 2-5
4325C–SCR–09/04
Section 2
Hardware Description
2.1 TDA8004 Mode
2.1.1 Overview The AT89EVK-01 board is soldered on the customer application by using the SO plug. If
there is a problem to connect the AT89EVK-01 board on the SO plug, connectors can
be added to lift the board.
Figure 2-1. General Description
Input signals of the TDA8004 footprint are connected to AT83C24.
Output signals of the TDA8004 footprint are provided by AT83C24.
The program stored in the Flash memory configures the AT83C24 registers once after
the reset. The functionalities of the TDA8004 are provided by the AT83C24.
Remarks:
The AT89EVK-01 board power supply comes from the TDA8004 footprint.
The program stored in the Flash memory configures the AT83C24 registers once after
the reset.
2.1.2 Clock signal (CLK)
The AT89EVK-01 board needs a clock signal. The AT89EVK-01 board needs a clock
signal for T89C5121 (XTAL1 pin) and for AT83C24 (CLK pin).
Customer board
TDA8004 footprint
SO plug
AT89EVK01board AT83C24
extra connectors
Hardware Description
2-6 AT89EVK-01 User Guide
4325C–SCR–09/04
Two solutions are proposed for the clock generation: waveform generator or crystal.
Figure 2-2. External Waveform Generator for Clock
Figure 2-3. Crystal for Clock
A solder pad (SW4) is used to configure the source: crystal or external waveform
generator.
2.1.3 Smart Card Clock
Signal (CCLK) The AT83C24 outputs the smart card clock signal (CCLK). Two modes are available to
generate this signal:
1. The source is CLK. The CKS prescaler is used to divide CLK signal or DCCLK
signal.
2. The source is A2. The CKS prescaler is used to divide A2 signal.
2.1.4 Power Supply The power supply comes from the TDA8004 footprint. The signal VDDP of the TDA8004
is used (5V).
The EVCC pin of the AT83C24 is connected to the VDD (3.3V). EVCC is used to supply
the AT83C24 pads connected to the customer application.
2.1.5 PRES, PRES\ The TWI_SEL switch is connected on an I/O of the T89C5121. The TDA8004
(TDA8024) PRES pin and PRES\ pin are connected on T89C5121 I/Os. The position of
Table 2-1. Clock Solder Pads Configuration
SW4 Configuration
without solder Waveform generator
with solder crystal
SO plug
AT83C24
AT89C5121 RESET
AT83C24 2.0.0
ATMEL
SCL
SDA
Rx
Tx
VCC
VSS
XTAL1
waveform
generator
SO plug
AT83C24
AT89C5121 RESET
AT83C24 2.0.0
ATMEL
SCL
SDA
Rx
Tx
VCC
VSS
XTAL1
14.74MHz
Hardware Description
AT89EVK-01 User Guide 2-7
4325C–SCR–09/04
the TWI_SEL switch selects the polarity of the smart card presence: information on
PRES or on PRES\ (see §2.1.8). See Figure 4-1 on page 16 for TWI_SEL selection.
Figure 2-4. Power Supply Configuration
Remark:
VCC and L1 must be connected to the same voltage.
2.1.6 TWI Link The TWI link is managed by T89C5121. The program stored in the Flash memory con-
figures the AT83C24 registers once after the reset.
The T89C5121 sends TWI commands. The AT83C24 TWI address depends on level on
A2,A1,A0 pins at reset. The T89C5121 sends TWI commands at all addresses to avoid
any problem of level on A2, A1, A0 at reset.
2.1.7 External TWI Link If the user wants to use an external TWI source to configure the AT83C24, the 2 test
points SCL and SDA are used.
To avoid any conflict with T89C5121 signals, the T89C5121 software must check the
SW2 signal before to send data on SCL and SDA.
2.1.8 Board configuration The table below describes the switches and solder pads configurations.
AT83C24
VCC
LI
L1
VDDP TDA8004 (5V)
EVCC
VDD TDA8004 (3.3V or 5V)
Table 2-2. Configuration Description
Solder pad
or Switch Default
Configuration Description
SW1 no solder RFU (TDA8004AT)
SW2 TWI_SEL = 0 Smart card presence detection:
TWI_SEL = 0: PRES indicates the smart card presence.
TWI_SEL = 1: PRES\ indicates the smart card presence.
SW5 Reset button
SW4 with solder Used for clock configuration (see §2.1.2)
SW9 solder Used to connect TDA8004 clock on A2 (transparent
mode). Use firmware from version 3 (at89evk01_V3.zip)
SW11 no solder Used to connect a pull up resistor on RESET pin
Hardware Description
2-8 AT89EVK-01 User Guide
4325C–SCR–09/04
2.2 T89C5121
Firmware
Reconfiguration
The program stored in the T89C5121 (Flash version) sends TWI commands to config-
ure the AT83C24 registers at each reset or power on.
If the user wants to modify the AT83C24 configuration, it need to reprogram the
T89C5121 Flash memory by using FLIP/BatchISP software (free download on
www.atmel.com) as described below.
Figure 2-5. T89C5121 In System Programming Description
2.2.1 CEIBO MP-51RD2
Programmer The CEIBO “MP-51RD2 Programmer” board is used to interface the RS-232 and the Rx
Tx pins of the T89C5121. This board makes the electrical interface between microcon-
troller signals (5V) and RS-232 signals (12V).
FLIP/BatchISP software
(ATMEL In System Programming software)
RS-232 CEIBO
MP-51RD2 board
EVK01 board
Rx, Tx signals (5V)
5V
Power Supply
Waveform
Generator
XTAL1
VCC
VSS
(14.74 MHz)
Hardware Description
AT89EVK-01 User Guide 2-9
4325C–SCR–09/04
Figure 2-6. CEIBO “MP-51RD2 Programmer” Board and J1 connector
Figure 2-7. CEIBO “MP-51RD2 Programmer” Board and AT89EVK-01 connections
2.2.2 AT83C24 registers
programming The Flash memory of the T89C5121 is loaded with FLIP/BatchISP if a new configuration
is needed for the AT83C24.
1. Unzip the AT89EVK01_Vx.zip (x : version)
This zip file contains 3 files :
– AT83C24_batchisp.hex : T89C5121 firmware file
– at89evk01.bat : DOS command file
– AT83C24_batchisp_prog.txt : script file for batchisp software
2. Copy all files at C:\Program Files\ATMEL\FLIP x.x.x\bin
3. Connect the external waveform generator - Frequency at 14.74MHz or solder
SW4
4. Connect the RS232C cable to PC serial port
5. Connect power supply to the AT89EVK-01 board
6. Switch on the power supply
7. Execute at89evk01.bat
RS-232 AT89EVK01boar
d
Rx(6)
Tx (4)
Vss(9)
Vcc (1)
J1
Vcc
Vss
Rx
Tx
1
9
4
6
5V Power Supply
Hardware Description
2-10 AT89EVK-01 User Guide
4325C–SCR–09/04
Figure 2-8. Execution of at89evk01.bat (V1.0)
Hardware Description
AT89EVK-01 User Guide 2-11
4325C–SCR–09/04
Figure 2-9. FLIP/BatchISP command script file AT83C24_batchisp_prog.txt (V1.0)
Following the application need, the AT83C24 registers can be changed. Only the value
of fillbuffer FLIP/BatchISP commands has to be modified. By default values of AT83C24
registers are:
Table 2-3. AT83C24 register address and default value
Register
Name Address
Default
Values
V1.0
Default
Values
V2.0
Default
Values
V3.0(1) Comments
Config0 0x26D 0x80 0x80 0x80
Config1 0x26E 0x0A 0x0A 0x0A
Config2 0x26F 0x00 0x24 0x24 Note: For Smart Card Clock frequency of
AT83C24 at 4.5MHz, XTAL1 must
be set at 4.5MHz - V1.0
Config3 0x270 0x80 0x80 0x80
Config4 0x271 0x0B 0x0B 0x0B
Interface 0x272 0x00 0x00 0x00
Note: 1. Default values are included in hex file
Hardware Description
2-12 AT89EVK-01 User Guide
4325C–SCR–09/04
Autres manuels Atmel Carte mère
Atmel
Atmel REB212BSMA Instructions d'utilisation
Atmel
Atmel ATmega328PB Xplained Mini Manuel utilisateur
Atmel
Atmel ATDH2200E Manuel utilisateur
Atmel
Atmel SAME70-XPLD Manuel utilisateur
Atmel
Atmel AT91SAM9G10-EK Manuel utilisateur
Atmel
Atmel PROTO1 Xplained Pro Manuel utilisateur
Atmel
Atmel STK526 Manuel utilisateur
Atmel
Atmel SAM4N Xplained Pro Manuel utilisateur
Atmel
Atmel AT90USB162 Manuel utilisateur
Atmel
Atmel ATBTLC1000 BluSDK Manuel utilisateur
Atmel
Atmel AVR910 Manuel utilisateur
Atmel
Atmel AT88CK109STK8 Manuel utilisateur
Atmel
Atmel SAM4E Xplained Pro Manuel utilisateur
Atmel
Atmel ATBTLC1000 BluSDK Manuel utilisateur
Atmel
Atmel AT91SAM9G45-EKES Manuel utilisateur
Atmel
Atmel ATA2270-EK1 Manuel utilisateur
Atmel
Atmel QT5 Xplained Pro Manuel utilisateur
Atmel
Atmel AT91SAM7SE-EK Manuel utilisateur
Atmel
Atmel AT73C224-EK1 Manuel utilisateur
Atmel
Atmel AT91SAM9G20-EK Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
