Atmel AT91 Series Instructions d'installation et d'utilisation

Software DMA Implementation

Introduction

A DMA (Direct Memory Access) Controller allows fast data transfers between memo-

ries without using the CPU. The transfer is activated by an external event. The control

signals and the address and data buses are managed by the DMA controller.

The AT91M40400 does not feature a DMA controller as a peripheral. However, it can

be implemented by software by using the load multiple (ldm) and store multiple (stm)

instructions (refer to the “ARM Architectural Reference Manual”).

This application note proposes two different ways to implement a software DMA using

the ARM Fast Interrupt (FIQ) as the external event. The code has been designed to

reduce the number of instruction fetches as much as possible.

Rev. 1169A–10/98

AT91 Series

ARM®Thumb®

Microcontrollers

Application Note

AT91 Series

Theory of Operation

The principle of DMA is that an external event causes a fast memory copy. In this case the external event is the Fast Inter-

rupt pin (FIQ) since the FIQ mode on the ARM7TDMI™processor has banked registers (r8 to r14) which do not need to be

saved before being used in FIQ mode. These registers are initialized before enabling the FIQ interrupt, then directly used

when the external event occurs.

This application note describes two ways to implement a software DMA. Both implementations make the transfer by split-

ting the block to be transferred into packets of 4 words.

Note: In this document 1 packet = 4 words; 1 word = 4 bytes

•DMA Turbo: Copies one packet (4 words) from a source buffer to a destination buffer at each FIQ interrupt.

•DMA Channel: Copies the number of packets (4 words) defined by the user from a source buffer to a destination buffer

at each FIQ interrupt, thus freeing the core between packets.

As the FIQ interrupt is used, the DMA must be able to access the banked registers. This can only be done by switching to

FIQ mode and only if the CPU is in privileged state (any mode except User Mode). This application note assumes that the

user function calls are performed while the CPU is in privileged state. It does not describe how to switch from unprivileged

to privileged state. This can be done on another level by using the “swi” instruction of the ARM core or the Advanced Inter-

rupt Controller features allowing an interrupt entry to be forced. In the last case, FIQ or AIC’s software interrupt can be

forced to set up software DMA.

DMA Turbo

The DMA Turbo allows 1 packet (4 words) to be transferred at each FIQ interrupt from a source buffer to a destination

buffer. Source and destination buffer pointers are post-incremented after each transfer.

The main advantage to this implementation is that no registers need to be saved. It is also a faster way to transfer data than

the DMA Channel implementation.

Table 1. Source Files

Files Contents

dma _turb.s Code source for DMA Turbo

dma_chnl.s Code source for DMA channel

dma.h DMA prototypes and structures for application use

arm.inc ARM core definition

Table 2. Registers Used

r14 Link register - return address

r13 ‘dest_pt’ = Destination buffer pointer

r12 ‘src_pt’ = Source buffer pointer

r8 to r11 Transfer registers

AT91 Series

User Functions

The functions used to manage the DMA Turbo are defined in

dma_turb.c

The DmaTurboSet function initializes the FIQ banked registers for the DMA Turbo transfer, then enables the DMA transfer

by clearing bit F in the CPSR.

void DmaTurboSet (int *source, int *destination)

source

the source buffer pointer

destination

the destination buffer pointer

Begin

| Switch to FIQ mode and save entry mode

| Memorize source buffer pointer (r12_fiq = 'src_pt')

| Memorize destination buffer pointer (r13_fiq = 'dest_pt')

| Enable DMA (Clear bit F)

| Restore entry mode

End

The DmaTurboGet function checks that the end of the transfer occurred (“size” words received), and, if it did, disables the

DMA transfer by setting bit F in the CPSR.

int DmaTurboGet (int * source, int size)

returns the number of words already received

source

the source buffer pointer at beginning

size

the number of words to be copied

Begin

| Switch to FIQ mode and save entry mode

| Calculate number of transferred words

| Disable DMA (Clear bit F) if number of transferred words >= size

| Restore entry mode

End

The DmaTurboFiq function is activated by the FIQ (vector address 0x1C), and copies 4 words from source buffer to desti-

nation buffer.

void DmaTurboFiq (void)

Begin

| *dest_pt <- *src_pt (multiple load and store 4 words with post increment)

End

Alternate Implementation

The DMA Turbo can be modified to transfer more than 4 words per FIQ. For this, the pair of instructions “ldm” and “stm”

(refer to the “ARM Architectural Reference Manual”) must be repeated as many times as necessary. Different types of

source and destination buffers can be supported by using the options of post/pre increment/decrement of these instruc-

tions.

It can also be modified to make the number of words to transfer defined by the caller. This has the advantage of allowing

the dynamic transfer size, but one register must be reserved for the count (e.g. r11). Therefore, only 3 registers are avail-

able for the transfer itself.

Table 3. DMA Turbo User Functions

void DmaTurboSet (int *source, int *destination) Initialize the FIQ registers for the DMA transfer

void DmaTurboGet (int *source, int size) Check the end of the transfer

void DmaTurboFiq (void) FIQ treatment and DMA transfer

AT91 Series

DMA Channel

The DMA Channel implementation copies the number of packets (4 words) defined by the user at each FIQ interrupt until

the remaining number of bytes is less than 1 packet (4 words). These remaining bytes are transferred at the following FIQ

interrupt, and the DMA is stopped by disabling the FIQ.

One inconvenience of this implementation is that non-banked registers are used. Therefore, it is mandatory to save these

registers before the transfer, and to restore them afterwards.

The main advantage is that the size of the transfer is controlled, and there is no risk of overwriting the memory.

The block is copied from the source to the destination by boundaries of packets. When no more whole packets can be

transferred, the remaining bytes (less than 16) are transferred in a way which optimizes the number of fetches:

• 2 words (8 to 15 remaining bytes)

• 1 word (4 to 7 remaining bytes)

• 1 half-word (2 or 3 remaining bytes)

• 1 byte (1 byte remaining)

The user can choose to increase, after each FIQ copy, the source pointer, the destination pointer, both pointers or neither.

Table 4. Registers Used

r14 Link register - return address

r13 Temporary buffer address

r12 Increment mask

r11 Number of packets to copy per FIQ

r10 Block size (byte number)

r9 Destination address

r8 Source address

r6 to r7 Working registers (must be saved and restored)

r0 to r3 Transfer registers (must be saved and restored)

AT91 Series

Type Definition

The DMA channel parameters are set through a structure named “dma_descriptor”. This type is defined in dma.h:

typedef struct dma_descriptor

{u_char *src; // Source pointer

u_char *dest; // Destination pointer

u_int nb_bytes; // Total number of bytes to copy

u_int nb_packets; // Maximum number of packets to copy at each FIQ

u_int dma_mask; // DMA channel mask (INC_SRC and/or INC_DEST)

} dma_descriptor;

The user can choose whether or not to increase the source/destination pointers using the “dma_mask” field, the value of

which is an OR-combination of the constants INC_SRC and INC_DEST (These constants are defined in dma.h).

User Functions

The functions used to manage the DMA Channel are defined in

dma_chnl.c

The DmaChannelSet function sets and enables the DMA Channel

void DmaChannelSet (dma_descriptor *dma_desc, int *buf);

dma_desc

pointer to the DMA descriptor

buf

temporary buffer (7*4 bytes needed) to store non-banked used registers

Begin

| Switch to FIQ mode and save entry mode

| r13_fiq <- temporary buffer pointer

| Load banked registers from the DMA descriptor

| Set default number of packets to transfer (1) if not defined by user

| Enable DMA (Clear bit F) if number of bytes to transfer > 0

| Restore entry mode

End

The DmaChannelGet function returns the remaining number of bytes to be transferred

int DmaChannelGet(void)

returns remaining number of bytes

Begin

| Switch to FIQ mode and save entry mode

| Return number of bytes remaining to be transferred

| Restore entry mode

End

Table 5. DMA Channel User Functions

void DmaChannelSet (dma_descriptor *dma_desc, int *buf) Initialize the FIQ registers for the DMA transfer

void DmaChannelGet (void) Get the count of remaining bytes to be transferred

void DmaChannelFiq (void) FIQ treatment and DMA transfer

AT91 Series

The DmaChannelFiq function is activated by the FIQ (vector address 0x1C), and copies r11 x 4 words from the <source>

to the <destination> if possible.

void DmaChannelFiq (void)

Begin

| Save used registers in the temporary buffer

| Save source and destination

| While (nb_packets > 0) and (nb_bytes >= PACKET_SIZE)

| | Update nb_bytes by subtracting PACKET_SIZE from it

| | *dest <- *src (multiple load and store 4 words with post increment)

| | Decrement nb_packets

| EndWhile

| If (nb_packets == 0) (i.e. All blocks transferred)

| Then

| | === Copy last bytes to copy (< 16) ===

| | *dest <- *src

| | If needed, load and store multiple 2 words with post increment

| | If needed, load and store 1 word with post increment

| | If needed, load and store 1 half-word with post increment

| | If needed, load and store 1 byte with post increment

| | Clear nb_bytes

| | Disable DMA (SPSR.F <- 0)

| Endif

| Restore src (if not INC_SRC)

| Restore destination (if not INC_DEST)

| Restore used registers

End

Required Resources

Table 6. DMA Turbo

Parameter Value

Code Size 20 words

registers)

Peripheral Usage FIQ Interrupt

Table 7. DMA Channel

Parameter Value

Code Size 51 words

registers)

Peripheral Usage FIQ Interrupt

AT91 Series

Tips and Warnings for Both Types of DMA Implementation

Pointer Alignment

Source and destination pointers must always be word-aligned because of the use of load and store multiple instructions. If

this is not the case, a word-alignment must be performed, using an “AND” with the existing word in the memory to copy the

first non-aligned bytes.

FIQ Rate

Since the DMA described in this application note performs the transfer of the packet(s) at the FIQ interrupt, it is necessary

to pace the FIQ at a rate defined by the application.

This application note does not describe how to generate the rate, but it can easily be done by using a timer channel which

is cyclically triggered to generate a tick. An FIQ is then generated on each tick. The FIQ can be generated by configuring

source 0 to be edge triggered, and by setting bit 0 in the AIC_ISCR register to one (0x00000001). The port P12, multi-

plexed with FIQ, should be configured as a PIO in order to prevent the FIQ from being generated by an external event.

Another way is to configure the port P12 as a peripheral, and to make the external hardware generate the FIQ which can be

configured to be edge or level triggered.

In any case, the source 0 (FIQ) of the AIC must be configured (register AIC_SMR0) and enabled (register AIC_IECR).

Tips and Warnings for DMA Channel Implementation

Temporary Buffer

This application does not implement a stack management to save the registers. For this reason, a temporary buffer has

been chosen in order to save and restore the non-banked registers in the function DmaChannelFiq. Of course, this tempo-

rary buffer can also be performed by a stack management. In this case, the function DmaChannelSet needs only the DMA

descriptor as a call parameter.

Pointer Incrementation

If the source and destination pointers are systematically incremented during the transfer, the command word with the

pointer management mask

ptrMask

is useless. In this case, the saving and conditional restoring of the source and destina-

tion pointers is also useless and the registers

and

are unused in the function DmaChannelFiq. As the mask is not

used, the register

R12

is also unused in the function DmaChannelFiq and can be used as the packet counter (in place of

R11

which must be restored).

This way only registers

in the function DmaChannelFiq must be saved, and the temporary buffer can be only 4-

word-sized.

Large Sized Blocks

If the blocks to transfer are significant (more than 15 words), the use of the registers can be optimized by increasing the

size of the temporary buffer.

and

are used only to save

and

. This can be done in the temporary buffer, and

whole non-banked registers (

and

) can be used for the transfer in the function DmaChannelFiq (care must be taken

however when restoring

and

The temporary buffer becomes 11 words (if optional increment feature is used), but the packets transferred are 8-words

(PACKET_SIZE).

It is necessary to add a 4-word conditional transfer before the 2-word transfer:

| | | *dest <- *src (load and store multiple 4 words with post

| | | increment) if needed

This is coded by:

ands r0, r10, #0x10

ldmneia r8!, {r0-r3}

stmneia r9!, {r0-r3}

Autres manuels pour AT91 Series

Table des matières

Autres manuels Atmel Microcontrôleur

Atmel

Atmel AT40K Instructions d'installation et d'utilisation

Atmel

Atmel ATtiny13A Manuel utilisateur

Atmel

Atmel ATZB-EVB-24-SMA Manuel utilisateur

Atmel

Atmel AVR AVR350 Instructions d'installation et d'utilisation

Atmel

Atmel AVR AT90CAN32 Manuel utilisateur

Atmel

Atmel AT90USB162 Manuel utilisateur

Atmel

Atmel ATmega328PB Xplained Mini Instructions d'installation et d'utilisation

Atmel

Atmel AT89C5130A-M Manuel utilisateur

Atmel

Atmel ATtiny26 Manuel utilisateur

Atmel

Atmel ATmega128 Manuel utilisateur

Atmel

Atmel AT18F-DK3 Manuel utilisateur

Atmel

Atmel AVR XMEGA-A3BU Instructions d'installation et d'utilisation

Atmel

Atmel AVR8015 Instructions d'installation et d'utilisation

Atmel

Atmel AVR128 Instructions d'installation et d'utilisation

Atmel

Atmel AVR2131 Manuel utilisateur

Atmel

Atmel ATF15 DK2 Series Manuel utilisateur

Atmel

Atmel AVR ATtiny15L Manuel utilisateur

Atmel

Atmel AVR365 Manuel utilisateur

Atmel

Atmel AT91 Series Manuel utilisateur

Atmel

Atmel AT97SC3205T-SDK2 Manuel utilisateur

Atmel

Atmel AVR461 Manuel utilisateur

Atmel

Atmel AVR4901 Instructions d'installation et d'utilisation

Atmel

Atmel AVR STK100 Manuel utilisateur

Atmel

Atmel ATmega48PV Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur