Atlas Copco SmartHEAD Manuel utilisateur

smartHEAD Installation Guide

1 (4) 9836 4569 01 Revision 4

smartHEAD INSTALLATION GUIDE

Index:

INSTALLING THE smartHEAD on the STwrench.................................................................................2

INSTALLING THE smartHEAD on the MRTT-C...................................................................................3

GENERAL

The smartHEAD, to be installed on the STwrench and MRTT-C,

defines the wrench capacity. You can install or change the smartHEAD

without the need of any further settings or calibration: the STwrench

and STanalyser loads automatically the transducer data at the power

on.

PACKAGE

Refer to the check list included for the package list.

SAFETY

Warning: Read the STwrench Product Instruction (No. 9836 4489 00) and MRTT-C User Guide (No.

9836 5984 01) before installing and using the product.

HANDLING

The module is electrostatic sensitive device; DO NOT touch any electrical contact to avoid risk of

module damages.

If possible, before handling any STwrench modules, touch with your hand a big metallic object,

in order to avoid electrostatic discharges while handling the modules.

Observe the following precautions to handle the module:

Correct handling: NOT correct handling:

smartHEAD Installation Guide

2 (4) 9836 4569 01 Revision 4

INSTALLING THE smartHEAD on the STwrench

1. SWITCH OFF THE STwrench.

2. INSERT THE smartHEAD IN THE WRENCH CONTROLLER AND TIGHTEN THE LOCKING NUT UNTIL

WHEN THE “CLICK” IS HEARD

NOTE: there is only one way to insert the smartHEAD into the wrench controller. The guide and

the reference pin must be inserted in the relative housings; do not force them in other position.

3. TURN ON THE STwrench

4. IF THE FOLLOWING MESSAGE IS SHOWN, CHECK THE DATE AND SELECT YES TO CONTINUE

AND USE THE smartHEAD (the first use date is set at the date shown):

Guide

Reference PIN

Locking nut

smartHEAD

smartHEAD Capacity Indication

STwrench

smartHEAD Installation Guide

3 (4) 9836 4569 01 Revision 4

Selecting No the first date is not set, but the smartHEAD is blocked. The messsage above is

shown again at the next STwrench power on.

5. IF THE smartHEAD IS NOT PROPERLY INSTALLED THE FOLLOWING MESSAGE IS SHOWN:

NOTE: each smartHEAD is intended to be associated to a single STwrench controller!

The smartHEAD interchangeability assures easy and fast maintenance operations and wrench

upgrade. IMPORTANT NOTE:

Assembling different heads on the same controller during the normal wrench operations is an

improper use of the modularity concept, and will invalidate the warranty on the wrench

components.

The smartHEAD should be left always connected to the controller. For example, do not

disassemble it at the end of the day of for wrench transportation.

INSTALLING THE smartHEAD on the MRTT-C

6. DISCONNECT THE MRTT-C FROM THE STanalyser / STa 6000.

Locking nut

smartHEA

MRTT

Date

smartHEAD Installation Guide

4 (4) 9836 4569 01 Revision 4

7. INSERT THE smartHEAD IN THE MRTT-C AND TIGHTEN THE LOCKING NUT UNTIL WHEN THE

“CLICK” IS HEARD

NOTE: there is only one way to insert the smartHEAD into the MRTT-C. The guide and the

reference pin must be inserted in the relative housings; do not force them in other position.

8. CONNECT THE MRTT-C TO THE STanalyser / STa 6000 AND TURN ON THE STanalyser / STa 6000

9. IF THE FOLLOWING MESSAGE IS SHOWN ON STa 6000, CHECK THE DATE AND SELECT YES TO

CONTINUE AND USE THE smartHEAD (the first use date is set at the STa 6000 date):

Selecting No the first date is not set, but the smartHEAD is blocked. The messsage above is

shown again at the next STa 6000 power on.

10. IF THE smartHEAD IS NOT PROPERLY INSTALLED THE Transducer Error MESSAGE IS SHOWN.

NOTE: each smartHEAD is intended to be associated to a single MRTT-C!

The smartHEAD interchangeability assures easy and fast maintenance operations and system

upgrade. IMPORTANT NOTE:

Assembling different heads on the same MRTT-C during the normal operations is an improper

use of the modularity concept, and will invalidate the warranty on the wrench components.

The smartHEAD should be left always connected to the MRTT-C. For example, do not

disassemble it at the end of the day of for transportation.

Guide

Reference PIN

Date / time

Table des matières

Autres manuels Atlas Copco Outils électriques

Atlas Copco

Atlas Copco RT-3 Manuel utilisateur

Atlas Copco

Atlas Copco ETDST101-500-20-T40 Feuille d'instructions

Atlas Copco

Atlas Copco ETP STB34-12-10-B Feuille d'instructions

Atlas Copco

Atlas Copco EBL55-RE Feuille d'instructions

Atlas Copco

Atlas Copco LG 204 Guide de maintenance et de service

Atlas Copco

Atlas Copco ETDST101-150-20 Manuel utilisateur

Atlas Copco

Atlas Copco ETVST101-450-20F Feuille d'instructions

Atlas Copco

Atlas Copco ITB-A61-50-10 Manuel utilisateur

Atlas Copco

Atlas Copco PRO W2611 Manuel utilisateur

Atlas Copco

Atlas Copco LSV28 S040-01M14 LF Instructions originales

Atlas Copco

Atlas Copco ETV S7 Manuel utilisateur

Atlas Copco

Atlas Copco RTX-14 Manuel utilisateur

Atlas Copco

Atlas Copco ETP STB34-06-10 Instructions originales

Atlas Copco

Atlas Copco EP7PTI55 HR10-MT Instructions originales

Atlas Copco

Atlas Copco LMS08 SR42 Feuille d'instructions

Atlas Copco

Atlas Copco LMB27 S014 Feuille d'instructions

Atlas Copco

Atlas Copco SB100 Caractéristiques techniques

Atlas Copco

Atlas Copco EP5PTI19 HR10-MT Feuille d'instructions

Atlas Copco

Atlas Copco QST62-230CT-T50-L202-H19 Feuille d'instructions

Atlas Copco

Atlas Copco AME 600 Guide de maintenance et de service

Atlas Copco

Atlas Copco ETDST101-150-20-T40 Feuille d'instructions

Atlas Copco

Atlas Copco EBL20-RE Manuel utilisateur

Atlas Copco

Atlas Copco LH 11 Manuel utilisateur

Atlas Copco

Atlas Copco QST42-50CT-T50-L334-H13 Feuille d'instructions

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel

Atlas Copco smartHEAD Manuel utilisateur

Manuels Outils électriques populaires d'autres marques