ATD Tools ATD-7317 Manuel de service

7137-DTA:ledoM noT2:yticapaC

ATD-7317

Low ProĮle Service Jack

Capacity Min. Height Max Height Handle

Length

Overall

Length

Overall

Width

Saddle

Diameter

Shipping

Weight

2 Ton 2 3/4” 24” 49-1/4” 36” 15-1/8” 4” 106 LB

Contents:

Page: 1. SpeciĮĐĂƟons

2. Safety & Warning /ŶĨŽƌŵĂƟŽŶ

3. & 4. Setup, OperĂƟŽŶ & PreveŶƟve Maintenance

5. InspĞĐƟon, Storage & TroubleƐŚŽŽƟŶŐ

6. Exploded View & Replaceable Part Numbers

7. Warranty /ŶĨŽƌŵĂƟŽŶ

8. PreveŶƟve Maintenance Record Log

ĞƌĂƟn

InstrucƟŽŶs & Parts Manual

7137-DTA:ledoM noT2:yticapaC

SAFETY & WARNING INFORMATION

IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE

Before ŽƉĞƌĂƟŶŐ this device, be sure to read all content within this manual, ensuring that you

understand the ŽƉĞƌĂƟŶŐ procedures, maintenance requirements and all safety warnings.

The owner and/or operator shall have an understanding of the product, its opĞƌĂƟng

characteriƐƟcs, and safety opĞƌĂƟng instrƵĐƟŽŶƐ before ŽƉĞƌĂƟŶŐ this device. Safety informaƟon

shall be emphasized and understood. If the operator is not ŇƵent in English, the product and

safety ŝŶƐƚƌƵĐƟŽŶƐ shall be read to and discussed with the operator in the operator’s ŶĂƟǀĞ

language by the purchaser/owner or his designee, making sure that the operator comprehends

their contents.

AcƟŽŶs to help prevent dangerous ƐŝƚƵĂƟŽŶs

Study, understand, and follow all instruĐƟons before ŽƉĞƌĂƟŶŐ this device.

Do not exceed the rated capacity stated.

Use only on hard level surfaces.

This item is to be used as a ůŝŌŝŶŐ device only. Immediately aŌer ůŝŌŝŶŐ support the

vehicle with appropriate means.

Do not move or dolly the vehicle while it is on the jack.

>ŝŌ only on areas of the vehicle as specŝĮed by the vehicle manufacturer.

No alƚĞƌĂƟons shall be made to this product.

Failure to heed these markings may result in serious personal injury and/or property

damage.

This is the safety ŶŽƟĮĐĂƟon symbol.

This symbol will ŶŽƟĨǇ you of any

potenƟal injury hazards. Please

follow all instrucƟŽŶƐ that follow this

symbol to avoid possible injuries or

death.

Indicates a hazardous

ƐŝƚƵĂƟŽŶ If proper steps are

not followed, death or

serious injury could result.

7137-DTA:ledoM noT2:yticapaC

SETUP, OPERATION & PREVENTIVE MAINTENANCEΎ

Setup

Prior to each use, visual inspeĐƟŽŶ (See Pg. 5) shall be made to the device by checking

for abnormal ĐŽŶĚŝƟŽŶƐ such as cracked welds, leaks, and damaged, loose, or missing

parts.

Consult the vehicle owner’s manual to determine the ůŽĐĂƟŽŶ of ůŝŌ points.

Be sure to set the vehicle in park with the emergency brake on and wheels securely

chocked.

Be sure that the vehicle and the jack are on a hard, level surface.

Assembly

If two piece handles are provided, assemble the upper ƐĞĐƟon into the lower secƟŽŶ

line up the holes, insert and Ɵghten the screw.

Insert the ďŽƩŽŵ end of handle into handle fork and securely Ɵghten the bolt and

washer. Ensure the handle can turn freely.

LiŌing

Turn the handle/release valve clockwise to the closed ƉŽƐŝƟŽŶ Do not over Ɵghten.

WŽƐŝƟŽŶ the jack under the specŝĮed ůŝŌ point.

Begin ůŝŌŝŶŐ by pumping the handle up and down.

Immediately ĂŌer ůŝŌŝŶŐ support the vehicle with appropriately rated jack stands.

Turn the handle/release valve slowly counterclockwise to lower the vehicle onto jack

stands.

Lowering

Turn the handle/release valve clockwise to the closed ƉŽƐŝƟŽŶ Do not over Ɵghten.

Pump the handle up and down to liŌvehicle Žī jack stands.

Remove the jack stands. Do not get under or let anyone get under the vehicle while

lowering.

Turn the handle/release valve slowly counterclockwise to lower the vehicle onto the

ground

7137-DTA:ledoM noT2:yticapaC

SETUP, OPERATION & PREVENTIVE MAINTENANCE (Cont.)

Maintenance

NOTICE: Use high grade hydraulic oil only. Never use brake ŇƵŝĚ motor oil, transmission ŇƵŝĚ

turbine oil or any other ŇƵŝĚƐ ISO-VG22 or equivalent hydraulic oil is recommended.

Check and ZĞĮll Oil

With the jack in the fully lowered, level ƉŽƐŝƟŽŶ if unit cover is provided, remove unit

cover, then remove oil Įller plug.

Proper oil level should be just covering inner cylinder as seen from the oil Įller plug

hole.

Do not ŽǀĞƌĮll. Always Įůů with new, clean hydraulic jack oil as recommended above.

Reinstall oil Įller plug, then reinstall unit cover.

LubricĂƟŽn and Cleaning

Periodically clean and lubricate all moving parts and pivot points.

Air sĞŶƟŶg Procedures

With the jack in the fully lowered ƉŽƐŝƟŽŶ release valve open, remove oil Įller plug.

Pump the handle rapidly several ƟŵĞƐ Reinstall oil Įller plug.

Turn the handle/release valve clockwise to the closed ƉŽƐŝƟŽŶ

Pump the handle ƵŶƟů the ůŝŌ arm reaches maximum height and conƟnue to pump

several Ɵmes to remove trapped air in the system.

Turn the handle/release valve counterclockwise in one full turn and lower ůŝŌ arm to the

lowest posiƟon. Use force on saddle if necessary.

Carefully and slowly loosen oil Įller plug to release pressurized air.

Repeat above steps ƵŶƟů trapped air is completely vented.

Damaged Equipment

Any jack that appears to be damaged in any way, is found to be worn, or operates abnormally

SHALL BE REMOVED FROM SERVICE UNTIL REPAIRED. It is recommended that necessary repairs

be made by a manufacturer’s or supplier’s authorized repair facility if repairs are permiƩĞd by

the manufacturer or supplier.

AlterĂƟŽŶs

Because of poteŶƟĂů hazards associated with this type of equipment, no alƚĞƌĂƟons shall be

made to the product.

ƩĂchments and Adapters

Only ĂƩĂchments and/or adapters supplied by the manufacturer shall be used.

7137-DTA:ledoM noT2:yticapaC

INSPECTION, STORAGE & TROUBLESHOOTING

/ŶƐƉĞĐƟŽn

Visual inspeĐƟŽŶ shall be made before each use of the device by checking for abnormal

ĐŽŶĚŝƟŽŶƐ such as cracked welds, leaks, and damaged, loose, or missing parts.

Other inspecƟŽŶƐ shall be made per product operĂƟŶŐ ŝŶƐƚƌƵĐƟŽŶƐ

This device shall be inspected immediately if the device is believed to have been

subjected to an abnormal load or shock. It is recommended that this inspĞĐƟon be made

by a manufacturer’s or supplier’s authorized repair facility.

Owners and/or operators should be aware that repair of this equipment may require

specialized knowledge and faciliƟes. It is recommended that an annual inspeĐƟŽŶ of the

product be made by a manufacturer’s or supplier’s authorized repair facility and that

any defeĐƟve parts, decals, or safety labels or signs be replaced with manufacturers or

supplier’s specŝĮed parts.

Storage

This Jack should be stored in a dry locaƟŽn on a level surface.

TroubleshŽŽƟngΎ

Symptom Possible Causes ^ŽůƵƟŽn

Jack will not ůŝŌ the load. 1. Release valve not ƟŐhtly

closed.

2. Low oil level.

3. DefeĐƟǀe or worn internal

parts.

4. Load exceeds maximum

allowance.

1. Tighten release valve.

2. Check and add oil. Follow “Check

and ZĞĮůů Oil” instrucƟons on Pg.4.

3. DisconƟnue use and contact a

local repair center.

4. Use a higher capacity jack.

Jack will not hold the load. 1. Release valve not ƟŐhtly

closed.

2. Power unit malfunĐƟŽn.

1. Tighten release valve.

2. DisconƟnue use and contact a

local repair center.

Jack will not descend to

minimum height, or will not

remain in lowered posŝƟŽŶ.

1. Air trapped in system.

2. Reservoir oil oǀĞƌĮlled.

1. Vent air out of system. Follow

“Air

VeŶƟng Procedures” above.

2. Check and ensure proper oil

level. Follow “Check and ZĞĮll Oil”

ŝŶƐƚƌƵĐƟŽŶ on Pg.4.

Jack will not ůŝŌ to max

height.

1. Low oil level. 1. Check and ensure proper oil level.

Follow “Check and ReĮůl Oil”

insƚƌƵĐƟŽŶƐ above.

Jack will not funcƟŽn

properly aŌer tried sŽůƵƟŽŶ.

1. Internal malfuncƟŽŶ or

structural damage.

1. Stop usage and contact an

authorized repair center.

7137-DTA:ledoM

noT2:yticapaC

EXPLODED VIEW & REPLACEABLE PART NUMBERS

* Items not ide ed by part number are not available for replacement.

346

Item Part Number* Descripon Q’ty

1LYD2G-100 Front Wheel Assembly 2

2LYD2K-300 Saddle w/ Pad 1

3GB1152-89-M6 Grease Fing 1

4LYD3J-3 Cover 1

5LYD3F-600 Handle Assembly w/ Foam 1

6LYD2-9A Return Springs 2

7LYDBI-2T.3 Power Unit Assembly 1

8LYD3G-300 Handle Fork Assembly 1

9LYD3G-400 Rear Caster Assembly 2

10 LYDBI-3T-17 Handle Foam only 1

11 LYD2K-3B Saddle Pad only 1

12 LYD3F-100 Oil Filler Screw w/ Seal 1

13 LYD3G-101 U-Joint 1

N/A ATD7317-L Label 1

7137-DTA:ledoM noT2:yticapaC

WARRANTY INFORMATION

ONE YEAR LIMITED WARRANTY

For a period of one (1) year from your purchase date, ATD Tools, Inc. will repair or replace (at its

option) without charge, your ATD product if it was purchased new and the product has failed

due to a defect in material or workmanship which you experienced during normal use of the

product. This limited warranty is your exclusive remedy.

To access the benefits of this warranty, contact the ATD warranty center at 1-844-364-9922 for

confirmation that this warranty applies. Thereafter, you may be advised to return the product

under warranty, freight prepaid, to the ATD Tools, Inc. service department.

If this ATD product is altered, abused, misused, modified, or undergoes service by an

unauthorized technician, your warranty will be void. We are not responsible for damage to

ornamental designs you place on this ATD product and such ornamentation should not cover

any warnings or instructions or they may void the warranty. This warranty does not cover

scratches, superficial dents, and other abrasions to the paint finish that occur under normal use.

Subject to the law in your state:

(1) Your sole and exclusive remedy is repair or replacement of the defective product as

described above.

(2) ATD Tools, Inc. is not liable for any incidental damages, including but not limited to, lost

profits and unforeseeable consequences.

(3) The repair and replacement of this product under the express limited warranty described

above is your exclusive remedy and is provided in lieu of all other warranties, express or

implied. All other warranties, including implied warranties and warranties of

merchantability or fitness for a particular purpose are disclaimed and, if disclaimer is

prohibited, these warranties are limited to one year from your date of purchase of this

product.

Some states’ laws do not allow limited durations on certain implied warranties and some states’

laws do not allow limitations on incidental or consequential damages. You should consult the

law in your state to determine how your rights may vary.

Made in China to ATD Tools, Inc. SpeciĮĐĂƟons

Visit us at www.atdtools.com

Warranty Service Number 1-844-364-9922

For Non-warranty issues, please contact your supplier.

Printed In China

7137-DTA:ledoM noT2:yticapaC

PREVENTIVE MAINTENANCE RECORD LOG

Date Maintenance Performed

Table des matières

Autres manuels ATD Tools Jack

ATD Tools

ATD Tools ATD-7433A Manuel utilisateur

ATD Tools

ATD Tools ATD-7387W Manuel utilisateur

ATD Tools

ATD Tools ATD-7343 Manuel utilisateur

ATD Tools

ATD Tools SwiftLift ATD-7325 Instructions d'utilisation

ATD Tools

ATD Tools ATD-7462 Manuel utilisateur

ATD Tools

ATD Tools ATD-7385W Manuel utilisateur

ATD Tools

ATD Tools ATD-7304A Manuel utilisateur

ATD Tools

ATD Tools ATD-7435A Manuel utilisateur

ATD Tools

ATD Tools 7345B Manuel utilisateur

ATD Tools

ATD Tools ATD-7500 Instructions d'utilisation

ATD Tools

ATD Tools ATD-7345B Manuel utilisateur

ATD Tools

ATD Tools MagicLift ATD7325 Instructions d'utilisation

ATD Tools

ATD Tools ATD-7383W Manuel utilisateur

ATD Tools

ATD Tools 7425A Manuel utilisateur

ATD Tools

ATD Tools ATD-7227B Manuel utilisateur

ATD Tools

ATD Tools ATD-7343A Manuel utilisateur

ATD Tools

ATD Tools ATD-7391A Manuel utilisateur

ATD Tools

ATD Tools ATD-7332A Instructions d'utilisation

ATD Tools

ATD Tools ATD-7406 Instructions d'utilisation

ATD Tools

ATD Tools 7343 Manuel utilisateur

ATD Tools

ATD Tools ATD-2025 Manuel utilisateur

ATD Tools

ATD Tools 7404 Manuel utilisateur

ATD Tools

ATD Tools ATD-7465 Manuel utilisateur

ATD Tools

ATD Tools ATD-7429 Manuel utilisateur

Manuels Jack populaires d'autres marques

Omega Lift Equipment

Omega Lift Equipment 18122C Instructions d'utilisation

Pittsburgh

Pittsburgh 58816 Instructions de montage

Unimec

Unimec TP Manuel utilisateur

Sonic

Sonic 4800703 Manuel utilisateur

BGS technic

BGS technic 70039 Manuel utilisateur

TradeQuip

TradeQuip 1128T Manuel utilisateur

VEVOR

VEVOR TJD-12000SP-F Manuel utilisateur

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Manuel utilisateur

Stels

Stels 51131 Manuel utilisateur

Bushranger

Bushranger RJX01 Manuel utilisateur

Clarke

Clarke CTJ2500QLG Manuel d'installation et d'exploitation

Valex

Valex 1650520 Manuel utilisateur

Pfaff

Pfaff Merkur M0 Manuel utilisateur

Beta

Beta 3050/K Supplément

Sealey

Sealey 1050CXHV Manuel utilisateur

Jung

Jung JH Series Manuel utilisateur

URIAH

URIAH UC200020 Manuel utilisateur

Kennedy

Kennedy KSJ010 Manuel utilisateur