AT&T BGW320 Manuel utilisateur

A simple guide

Setting Up

Your Battery

Backup

BGW320INDOORONT

How to Install:

PSI Rechargeable Battery Units for your Gateway

Before you begin:

Each battery stack will provide up to 16 hours of backup power. One battery

stack will be connected to the Gateway to provide automatic backup and will

need to be replaced with the other standby battery stack as needed during

an outage.

Keep standby rechargeable battery stack connected to power source to

maintain charge.

Prepare standby backup

rechargeable batteries

Connect the other three rechargeable batteries and the power supply to the

other backplane and plug into an electrical outlet (not controlled by a wall

switch). Note: to get the best power available, you should plug your battery

stack directly into a wall receptacle.

What you need:

•(2) PSI Li-75 Power Supplies

•(6) PSI PS36L-EX Batteries

•PSI-BGW320 Adapter Cable

1 2

Connect ﬁrst backup battery:

Disconnect existing black

power supply from the

Gateway and wall outlet.

Stack three battery units

and the power supply on the

backplane.

3Connect the rechargeable 4

battery stack to the Gateway

using supplied power cord.

Make sure the battery is On

and the Gateway is working.

Completed Setup

Replace your batteries:

How to Check & Replace:

PSI Rechargeable Battery Units

2Connect the fully charged

standby battery stack into

the Gateway.

1Unplug the entire battery

stack from the Gateway.

3Press the Cold Start Button on 4

the Power Supply.

Press the Power Button on

the Gateway.

Important information:

•Each battery stack will provide up to 16 hours of backup power. One stack

will be connected to the Gateway to provide automatic backup and

should be replaced as needed. The other will be a standby battery stack

to use during a power outage.

•Keep all rechargeable batteries connected to a power source to

maintain charge.

Note: Battery Backup unit will not power a cordless phone. It will only power

a corded phone.

Recharge your batteries:

Make sure the old battery is connected to the power outlet so it will recharge

when the power comes back on.

Check your batteries:

It’s important to check your batteries periodically to ensure full charge in

case of a power outage. Your batteries will automatically display the charge

level when turned on—if the battery is exhausted, replace it with one of

the standby units.

How to Install:

D-cell Unit for your AT&T Fiber Service Box

1 2

Follow these simple steps:

Unplug existing black

power supply.

Remove plastic cover from

bottom of power supply.

Connect new power cable to

ONT and D-cell power supply,

then plug into outlet.

5Test the unit: Push Test 6

button; LED lights will indicate

power level.

ONT Power Cable

and Supply

ONT

D-Cell Battery

Power Supply

Outlet

ONT

Turn unit Oﬀ when ﬁnished

testing. You will need to

turn the unit back on during

a power outage.

Insert all 12 D-cell batteries

into the holder.

D-cell Battery Holder

(Open Cover)

Plug holder into power supply.

3 4

D-cell Battery

Holder

D-cell Battery

Power Supply

Before you begin:

Determine placement of D-cell unit near the AT&T network box (ONT).

Unit can be laid ﬂat or mounted to wall.

Select the power cable that ﬁts your ONT.

In your kit:

•D-cell batter holder with cable

•D-cell power supply

•Power cables (2)

You will need to supply 12 D-cell alkaline batteries.

Completed Setup (items not to scale)

D-cell Battery Holder

New ONT Power Cable

D-cell Battery Power Supply

AT&T Network Box

(ONT)

(Open Cover)

How to Check & Replace:

D-cell Units

Important information:

•It’s important that you periodically check your batteries to ensure they’re

functioning properly. Batteries have a limited lifespan, even if they are not

in use. Older batteries may not provide a full 24 hours of backup. We

recommend that you have a spare set of new alkaline batteries available.

•During a power outage, you may need to replace the batteries more than

once to maintain working service.

•When replacing batteries, replace All of them at the same time with the

same type and brand of alkaline batteries. Caution: Do not mix old and new

batteries or use rechargeable batteries as it could damage the device.

Note: Backup battery will not power a cordless phone, it will only power a

corded phone.

Check your batteries:

It’s important to check your batteries from time to time to ensure you’ll have

service if there’s a power outage.

Press Test button on the D-cell holder. The LED lights will indicate how much

charge is le. Replace all 12 batteries with fresh batteries if necessary.

Replace your batteries:

2Insert the 12 New D-cell

batteries into holder.

1Turn the D-cell unit Oﬀ.

Open cover of D-cell holder

and remove all 12 of the old

D-cell batteries.

3Push Test button on D-cell 4

holder. LED lights will indicate

power level. (See chart below.)

Turn unit Oﬀ when ﬁnished

testing. You will need to turn

the unit back on during a

power outage.

LED Indicator Condition

Good

Fair

Poor

Replace

D-cell Battery Holder

Check your Gateway and

Rechargeable Batteries

NEED MORE HELP & TROUBLESHOOTING?

Check your AT&T Fiber Service Box/ONT

and D-cell Battery Unit

If your phone does not have a dial tone during a power outage:

Troubleshooting:

For D-cell & PSI Rechargeable Battery Units

D-cell Battery Unit:

go to att.com/dcellbatterybackup or call 800.650.0954

PSI Rechargeable Battery Units:

go to www.powertecsolutions.net/solutions/att-solutions/

If Gateway does not have power, make sure:

•Gateway is plugged into rechargeable battery

•Rechargeable battery is turned On

•Rechargeable battery still has a charge. If not, replace

it with one of the standby rechargeable batteries.

If AT&T network box (ONT) does not have power, make sure:

•D-cell holder is plugged into power supply

•D-cell holder is turned On

•Power supply is plugged into AT&T network box (ONT)

•D-cell batteries are installed and have enough charge.

(Push the battery Test button to see the battery

power level.) If not suﬃciently powered, replace All the

D-cell batteries.

1Make sure corded phone is plugged into the Gateway. 1 Make sure AT&T network box (ONT) has power and is

turned On.

Make sure Gateway is connected to AT&T network box.

Table des matières

Autres manuels AT&T Porte

AT&T

AT&T U-verse TV Manuel utilisateur

AT&T

AT&T SB67070 SIP Manuel utilisateur

AT&T

AT&T Pace 5031 Manuel utilisateur

AT&T

AT&T U-verse TV Manuel utilisateur

AT&T

AT&T U-verse TV Manuel utilisateur

AT&T

AT&T 5031 Manuel utilisateur

AT&T

AT&T U-verse TV Manuel utilisateur

AT&T

AT&T U-verse TV Manuel utilisateur

AT&T

AT&T U-verse Voice Self Manuel utilisateur

AT&T

AT&T NVG599 Manuel utilisateur

AT&T

AT&T U-verse TV Manuel utilisateur

AT&T

AT&T NVG599 Manuel utilisateur

AT&T

AT&T U-verse TV Guide de sécurité

AT&T

AT&T NVG589 Manuel utilisateur

AT&T

AT&T U-verse TV Manuel utilisateur

AT&T

AT&T Syn248 SB35031 Manuel utilisateur

AT&T

AT&T NVG589 Manuel utilisateur

AT&T

AT&T U-verse NVG589 Manuel utilisateur

AT&T

AT&T U-verse TV Manuel utilisateur

AT&T

AT&T RIM BlackBerry 8300 Manuel utilisateur

AT&T

AT&T 5168 Manuel utilisateur

AT&T

AT&T 3800 Manuel utilisateur

AT&T

AT&T U-verse Wi-Fi Gateway Manuel utilisateur

AT&T

AT&T 3800 Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur

RTA

RTA 460MCBC-N2E Fiche technique