Asus IPILP-AR Manuel utilisateur
Motherboard
IPILP-AR
ii
Checklist
Contents
IPILP-AR specications summary ............................................................ iii
1. Motherboard layout......................................................................... 1
2. Central Processing Unit (CPU) ...................................................... 2
2.1 Enhanced Intel SpeedStep® Technology (EIST) ..................... 2
2.2 Installing the CPU ..................................................................... 3
3. System memory .............................................................................. 5
3.1 Memory congurations ............................................................ 5
3.2 Installing a DIMM....................................................................... 6
3.3 Removing a DIMM ..................................................................... 6
4. Expansion slots............................................................................... 7
5. Jumper ............................................................................................. 8
6. Connectors.......................................... .......................................... 10
6.1 Rear panel connectors ........................................................... 10
6.2 Internal connectors................................................................. 12
E3030
First Edition V1
January 2007
iii
IPILP-AR specications summary
CPU Intel®socket LGA775 Conroe/ Celeron processor
2006FMB (TDP=65W)
Chipset Nortbridge: Intel® 945G GMCH
Southbridge: Intel® ICH7DH
Front Side Bus 1066/800/533 MHz
Memory Dual channel memory architecture
2 x 240-pin DIMM sockets support up to 2 GB non-
ECC 1.8V DDR SD RAM (Register DIMM is not
supported)
Expansion slot 1 x PCI Express x 16 Graphics connector
Rear panel 1 x PS/2 mouse port
1 x PS/2 keyboard port
1 x VGA port
1 x IEEE 1394a port
1 x LAN (RJ-45) port
6 x audio ports support 8-channel High Denition
Audio
8 x USB 2.0 ports support hot-plug function
1 x S/PDIF Out port
Internal connectors 1 x 24-pin ATX Micro-Fit power connector
2 x Serial ATA connectors
1 x IEEE 1394a connector
8 x USB 2.0 connectors
1 x System fan connector
1 x S/PDIF Out connector
1 x Front headphone connector
1 x System panel connector
Storage Southbridge supports:
Support Ultra DMA 300 Serial ATA Device
Audio Support HD Audio codec that includes line-in, line-out
(8 Channel), microphone-in, SPDIF
Realtek Audio Codec ALC888
LAN Intel 82562GT (Ekron-GT) 10/100Mbps Ethernet PHY
(48-pin SSOP)
IEEE 1394 Agere LFW3226 with 1 ports PHY
BIOS feature Award Code Base
8MB SPI Flash
HP BIOS with Enhanced ACPI, DMI, Green, PnP
Features Plus
Form factor Mini-ITX Variant Form Factor: 190mm x 173mm
*Specications are subject to change without notice.
iv
ASUS IPILP-AR 1
1. Motherboard layout
17.3cm (6.8in)
PCIEX1
IPILP-AR
PS/2KBMS
T: Mouse
B: Keyboard
ALC888
CLEAR P.W
CLEAR CMOS
SYS_FAN1
19.3cm (7.5in)
BUZZ1
1394_USB1
AUDIO1
F_AUDIO1
ATXPWR1
SATA1
SPDIF_OUT1
VGA1
BAT1
F_PANEL1
LAN_USB1
FRONT_USB2
SPDIF1
PCI1
SATA2
FRONT_USB1
DDR2 DIMM1 (64 bit,240-pin module)
LGA775
DDR2 DIMM2 (64 bit,240-pin module)
Intel
ICH7DH
Intel
945G
8MB SPI Flash
Agere
LFW3226
ASUS IPILP-AR
2
2.1 Enhanced Intel SpeedStep® Technology (EIST)
• The motherboard comes with a BIOS le that supports EIST.
• Visit www.intel.com for more information on the EIST feature.
System requirements
Before using EIST, check your system if it meets the following requirements:
• Intel®Yonah®Mobile processor with EIST support
• BIOS le with EIST support
• Operating system with EIST support (Windows®XP SP2/Windows®Server 2003
SP1/Linux 2.6 kernel or later versions)
Using the EIST
To use the EIST feature:
1. Turn on the computer, then enter the BIOS Setup.
2. Go to the Advanced Menu, highlight CPU Conguration,then press <Enter>.
3. Set the Intel(R) SpeedStep Technology item to [Automatic], then press
<Enter>.
4. Press <F10> to save your changes and exit the
BIOS setup.
5. After the computer restarts, right click on a blank
space on the desktop, then select Properties from
the pop-up menu.
6. When the Display Properties window appears, click
the Screen Saver tab.
7. Click the Power button on the Monitor power section
to open the Power Options Properties window.
2. Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA775 socket designed for the
Intel®Core™2 DUO, Celeron® D and Conroe-L processors.
•
Upon purchase of the motherboard, make sure that the PnP cap is on
the socket and the socket contacts are not bent. Contact your retailer
immediately if the PnP cap is missing, or if you see any damage to the PnP
cap/socket contacts/motherboard components. ASUS will shoulder the cost
of repair only if the damage is shipment/transit-related.
•
Keep the cap after installing the motherboard. ASUS will process Return
Merchandise Authorization (RMA) requests only if the motherboard comes
with the cap on the LGA775 socket.
• The product warranty does not cover damage to the socket contacts
resulting from incorrect CPU installation/removal, or misplacement/loss/
incorrect removal of the PnP cap.
ASUS IPILP-AR 3
8. On the Power schemes section, click , then select any option except Home/Ofce
Desktop or Always On.
9. Click Apply, then click OK.
10. Close the Display Properties window.
After you adjust the power scheme, the CPU
internal frequency slightly decreases when the
CPU loading is low.
The screen displays and procedures
may vary depending on the operating
system.
2.2 Installing the CPU
To install a CPU:
1. Locate the CPU socket on the motherboard.
Before installing the CPU, make sure that the cam box is facing towards you
and the load lever is on your left.
IPILP-AR
IPILP-AR CPU Socket 775
2. Press the load lever with your thumb (A), then move it to the left (B) until it is
released from the retention tab.
Retention tab
Load lever
This side of the socket box
should face you.
PnP cap
A
B
To prevent damage to the socket pins, do not remove the PnP cap unless you
are installing a CPU.
ASUS IPILP-AR
4
3. Lift the load lever in the direction of
the arrow to a 135º angle.
5. Position the CPU over the
socket, making sure that
the gold triangle is on the
bottom-left corner of the
socket then t the socket
alignment key into the
CPU notch.
Alignment key
Gold triangle mark
The CPU ts in only one correct orientation. DO NOT force the CPU into the
socket to prevent bending the connectors on the socket and damaging the CPU!
4. Lift the load plate with your thumb
and forenger to a 100º angle (A),
then push the PnP cap from the load
plate window to remove (B).
Load plate
A
B
CPU notch
6. Close the load plate (A), then
push the load lever (B) until it
snaps into the retention tab.
7. If installing a dual-core CPU,
connect the chassis fan cable
to the CHA_FAN1 connector to
ensure system stability.
A
B
The motherboard supports Intel®LGA775 processors with the Intel®Enhanced
Memory 64 Technology (EM64T), Enhanced Intel SpeedStep®Technology
(EIST), and Hyper-Threading Technology. Refer to the Appendix for more
information on these CPU features.
ASUS IPILP-AR 5
3. System memory
The motherboard comes with two Double Data Rate (DDR) Dual Inline Memory
Modules (DIMM) sockets.
The following gure illustrates the location of the DDR DIMM sockets:
3.1 Memory congurations
You may install 256 MB, 512 MB, 1 GB, and 2 GB unbuffered non-ECC DDR
DIMMs into the DIMM sockets.
•
Installing DIMMs other than the recommended congurations may cause
memory sizing error or system boot failure. Use any of the recommended
congurations on the next page.
•
In Dual-channel configurations, install only identical (the same type and
size) DDR DIMM pairs for each channel.
•
Always install DIMMs with the same CAS latency; otherwise, the system
may run at a lower frequency. For optimum compatibility, we recommend
that you obtain memory modules from the same vendor.
•
When both sockets are populated with 2 GB DIMMs (total 4 GB), the
system may detect only 3583 MB due to the Southbridge resource
allocation.
• Make sure that the memory frequency matches the CPU FSB. Refer to the
next page for congurations.
IPILP-AR
IPILP-AR 240-pin DDR2 DIMM sockets
DIMM1
DIMM2
ASUS IPILP-AR
6
3.2 Installing a DIMM
Unplug the power supply before adding or removing DIMMs or other
system components. Failure to do so can cause severe damage to both the
motherboard and the components.
To install a DIMM:
1. Unlock a DIMM socket by pressing
the retaining clips outward.
2. Align a DIMM on the socket
such that the notch on the DIMM
matches the break on the socket.
3.3 Removing a DIMM
Follow these steps to remove a DIMM.
3. Firmly insert the DIMM into the
socket until the retaining clips snap
back in place and the DIMM is
properly seated.
Locked retaining clip
1. Simultaneously press the retaining
clips outward to unlock the DIMM.
2. Remove the DIMM from the socket.
Unlocked retaining clip
DDR DIMM notch
A DDR DIMM is keyed with a notch so that it ts in only one direction. DO NOT
force a DIMM into a socket to avoid damaging the DIMM.
Support the DIMM lightly with your ngers when pressing the retaining clips.
The DIMM might get damaged when it ips out with extra force.
Table des matières
Autres manuels Asus Carte mère
Asus
Asus Q470EI-IM-A Manuel utilisateur
Asus
Asus Z170 PRO GAMING Manuel utilisateur
Asus
Asus Republic Of Gamers ROG STRIX B550-I GAMING Manuel utilisateur
Asus
Asus P5N-T Deluxe Manuel utilisateur
Asus
Asus P8H77-V Instructions d'utilisation
Asus
Asus Q270M-CM-A Manuel utilisateur
Asus
Asus H610M-IM-A Manuel utilisateur
Asus
Asus M5A97 R2.0 Manuel utilisateur
Asus
Asus A7V400-MX SE Manuel utilisateur
Asus
Asus PRIME H310M-D R2.0 Manuel utilisateur
Asus
Asus P5K WS Manuel utilisateur
Asus
Asus UPX-EDGE-TGL01 Manuel utilisateur
Asus
Asus TR-DL Manuel utilisateur
Asus
Asus A8R32-MVP DELUXE Manuel utilisateur
Asus
Asus P5E-VM - Motherboard - Micro ATX Manuel utilisateur
Asus
Asus P8P67 LX Manuel utilisateur
Asus
Asus P5K - AiLifestyle Series Motherboard Manuel utilisateur
Asus
Asus M5A97 LE R2.0 Manuel utilisateur
Asus
Asus Maximus V Extreme Manuel utilisateur
Asus
Asus Rambus P3C-L Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
Biostar
Biostar M7VIT Bravo Instructions d'utilisation et d'installation
Intel
Intel D33217CK Manuel utilisateur
