Aries Embedded MCV Series Manuel utilisateur
MCV Quick Start Guide
Release 2
ARIES Embedded GmbH
April 28, 2020
CONTENTS
1 About this manual 1
1.1 Imprint .................................................. 1
1.2 Disclaimer ................................................ 1
1.3 Copyright ................................................. 1
1.4 Registered Trademarks .......................................... 1
1.5 Care and Maintenance .......................................... 2
2 Intial Operation 3
2.1 Apply Correct Jumper Settings ..................................... 3
2.2 Mount the MxxDK Displaykit on MCVEVP .............................. 4
2.3 Start your Linux Computer and install ckermit ............................. 6
2.4 Configure kermit ............................................. 7
2.5 Start kermit and connect ......................................... 7
2.6 Connect the console cable ........................................ 7
2.7 Connect power to your kit ........................................ 8
2.8 Have fun ! ................................................ 10
2.9 Shut down your kit ............................................ 10
3 Update eMMC Memory 11
3.1 Perform initial operation ......................................... 11
3.2 Connect MCVEVP to your PC ...................................... 11
4 Recovery 15
4.1 Modify boot settings ........................................... 15
4.2 Connect USB Blaster and USB A-miniB cable ............................. 15
4.3 Open a Console .............................................. 15
4.4 Power up the board ............................................ 15
4.5 Start Quartus Programmer ........................................ 15
4.6 Use USB Mass Storage ......................................... 16
i
ii
CHAPTER
ONE
ABOUT THIS MANUAL
1.1 Imprint
Adress:
ARIES Embedded GmbH
Schöngeisinger Str. 84
D-82256 Fürstenfeldbruck
Germany
Phone:
+49 (0) 8141/36 367-0
Fax:
+49 (0) 8141/36 367-67
1.2 Disclaimer
ARIES Embedded does not guarantee that the information in this document is up-to-date, correct, complete or of good
quality. Liability claims against ARIES Embedded, referring to material or non-material related damages caused,
due to usage or non-usage of the information given in this document, or due to usage of erroneous or incomplete
information, are exempted, as long as there is no proven intentional or negligent fault of ARIES Embedded. ARIES
Embedded explicitly reserves the rights to change or add to the contents of this Preliminary User’s Manual or parts of
it without notification.
1.3 Copyright
This document may not be copied, reproduced, translated, changed or distributed, completely or partially in any form
without the written approval of ARIES Embedded GmbH.
1.4 Registered Trademarks
The contents of this document may be subject of intellectual property rights (including but not limited to copyright,
trademark, or patent rights). Any such rights that are not expressly licensed or already owned by a third party are
reserved by ARIES Embedded GmbH.
1
MCV Quick Start Guide, Release 2
1.5 Care and Maintenance
• Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will
corrode electronic circuits. If your device does get wet, allow it to dry completely.
• Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged.
• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage
batteries, and warp or melt certain plastics.
• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form
inside the device and damage electronic circuit boards.
• Do not attempt to open the device.
• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
• Do not paint the device. Paint can clog the moving parts and prevent proper operation.
• Unauthorized modifications or attachments could damage the device and may violate regulations governing
radio devices.
2 Chapter 1. About this manual
CHAPTER
TWO
INTIAL OPERATION
The following steps guide you to the correct settings of your MCVEVP.
2.1 Apply Correct Jumper Settings
Pin 1 of each header is marked with a yellow dot in the picture.
1. place jumpers on P25 and P29 to activate the UART0 interface
2. leave jumper P32 open to select eMMC boot mode for MCV
3. place jumper to connect pin 1 and pin 2 on connector JP4 to connect VCCIO3B4A to 3.3V
4. Insert the MCV SoM into the Samtec connectors on MCVEVP
3
MCV Quick Start Guide, Release 2
! CAUTION ! |
Electronic components are sensitive against mechanical pressure. Certain contacts/housings may mechanically break
when mechanical force is applied to the board. Due to the insertion force that has to be applied to the two board-to-
board connectors the user has to press on the MCV pcb to insert it on a baseboard.
The following image shows the do not touch area when inserting the board on a baseboard.
DO NOT APPLY ANY MECHANICAL PRESSURE TO THE MARKED AREAS
Disregard of this provision may break the components and/or the contacts of the BGA components.
Please make sure that the TOP side of the Altera logo on the CPU is facing the ethernet connector when inserting the
SoM into the EVK.
2.2 Mount the MxxDK Displaykit on MCVEVP
Note: MxxDK is compatible with MCVEVP V1.0. For MCVEVP V2.0 please refer to the MxxDK2.
Open the FPC connector on the backside of your MxxDK carefully
4 Chapter 2. Intial Operation
MCV Quick Start Guide, Release 2
Place the FPC cable in the FPC connector on MxxDK, the contact side has to be placed towards the TFT PCB so that
the isolation of the cable is on top. Close the FPC connector on the MxxDK carefully.
Place the FPC cable in the FPC connector on MCVEVP, the contact side has to be placed towards the TFT PCB so
that the isolation of the cable is on top. Close the FPC connector on the MCVEVP carefully.
2.2. Mount the MxxDK Displaykit on MCVEVP 5
MCV Quick Start Guide, Release 2
Place the MxxDK Displaykit on MCVEVP without twisting or disconnecting the FPC cable. Mount the MxxDK
Displaykit on MCVEVP by using four screws.
2.3 Start your Linux Computer and install ckermit
Boot your Linux Computer and log in. Open a console port and install ckermit (if not already installed):
sudo apt-get install ckermit
After typing in your sudo password ckermit will be installed.
6 Chapter 2. Intial Operation
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Aries Embedded Carte mère
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
