APsystems YC600 Manuel utilisateur
2019/06/20 Rev4.1 Quick Installation Guide
1
YC600 Microinverter Quick Installation Guide
Step 1. Verify the grid voltage to match with the microinverter rating
Step 2. The AC bus distribution
a. The AC bus is arranged at the proper position of the microinverter.
b. One end of the AC bus access junction box into power grid.
c. Wire the conductors of the AC bus: L - BROWN; N - BLUE；PE - YELLOW GREEN.
NOTE: Wiring colour code can be different according local regulation, check all the wires of the installation before
connecting to the AC bus to be sure they match. Wrong cabling can damage irreparably the microinverters, such an issue is
not covered by the warranty.
Step 3. Attach the APsystems microinverters to the racking
NOTE: Do not place the microinverters (including DC and AC connectors) where exposed to the sun, rain or snow, even gap
between modules. Allow a minimum of 2 cm between the roof and the bottom of the microinverter to allow proper air
flow. The racking on which the microinverter is installed must be reliably grounded.
a. Mark the location of the microinverter on the rack, with respect to the PV module junction box or any other
obstructions.
b. Mount one microinverter at each of these locations using hardware recommended by your module racking
vendor. When installing the microinverter, grounding washer must be facing the racking.
Step 4. Ground the system
a. An earth wire is already inside the AC cable, thus the grounding work can be done directly
with it.
Please scan the QR code to get
mobile app and more support to
help the installation.
grounding washer
2019/06/20 Rev4.1 Quick Installation Guide
2
b. For geographical areas having special requirements, the external grounding can be done by using the
grounding brackets.
Step 5. Connect the APsystems microinverter to AC bus cable
Push the microinverter AC connector to the trunk cable connector. Listen for the "Click".
NOTE: AC connector interface as follows. NOTE: Cover any unused connectors with
Bus Cable Y-CONN Cap to protect the connectors.
Step 6. Install a Bus Cable End Cap at the end of AC bus cable
a. Strip cable jacket. c. Insert the wires into the cable clamps.
b. Insert the cable end into the seal. d. Rotate the nut with 3.3N·m until the
latching mechanism meets the base.
Nut
Seal
Body
Click
Best Practice: Use the Bus Cable Unlock
Tool of AC Bus to split the connectors.
grounding brackets
2019/06/20 Rev4.1 Quick Installation Guide
3
Step 7. Place the PV modules and connect each YC600 to the PV modules
Step 8. Finalizing the APsystems installation
a. Each APsystems microinverter has removable serial number labels.
b. Peel labels off, affix one to the respective location on the APsystems installation map, and fill in 1,2 in the
label below, according to the layout on the roof.
c. The other serial number label posted on the solar module frame is easy to find.
d. Log on to the EMA with your installer access details, then you can create a user account in EMA and
register the installation (including the ECU). There, you can also upload a photo of the installation map.
NOTE: you can request an EMA installer account at https://emea.apsystems.com/resources/register/
NOTE: Sequence of steps 1 to 8 can be changed depending on the installation.
NOTE: Using APsystems' mobile app ECUAPP can make the installation and registration much simpler when there is an ECU
included in the installation.
Step9.Start the operation
1. Turn on the AC circuit breaker on each microinverter AC branch circuit.
2. Turn on the main utility-grid AC circuit breaker. Your system will start producing. power after a two-minute waiting
time.
Product information is subject to change without notice.
(Please download manuals at emea.APsystems.com).
Autres manuels pour YC600
4
Table des matières
Autres manuels APsystems Onduleur
APsystems
APsystems QT2 Manuel utilisateur
APsystems
APsystems YC600 Manuel utilisateur
APsystems
APsystems QS1 Manuel utilisateur
APsystems
APsystems YC500A-EU Manuel utilisateur
APsystems
APsystems YC1000-3 3-Phase Mode d’emploi
APsystems
APsystems QS1 Manuel utilisateur
APsystems
APsystems YC1000-3-208 Mode d’emploi
APsystems
APsystems QS1 Manuel utilisateur
APsystems
APsystems YC600 Mode d’emploi
APsystems
APsystems YC1000-3-220 Manuel utilisateur
APsystems
APsystems YC500i Series Mode d’emploi
APsystems
APsystems QS1A Mode d’emploi
APsystems
APsystems YC1000-3-3 Manuel utilisateur
APsystems
APsystems YC600 Manuel utilisateur
APsystems
APsystems QT2 Manuel utilisateur
APsystems
APsystems DS3D Manuel utilisateur
APsystems
APsystems YC500A Mode d’emploi
APsystems
APsystems QS1A Manuel utilisateur
APsystems
APsystems DS3D-AU Manuel utilisateur
APsystems
APsystems DS3-S Manuel utilisateur
