APsystems QS1-LK Manuel utilisateur

2018/07/26 Rev1.0 Quick Installation Guide

QS1-LK Microinverter Quick Installation Guide

The sketch of QS1 support system.

All the PV modules are placed into two lines. Then put a QS1 in the middle of the two lines and make

sure it is easy to connect with four PV modules which are next to it, as well all the cables.

Step 1. Verify the grid voltage to match with microinverter rating

Step 2. The AC bus distribution

a. The AC bus is arranged at the proper position of the microinverter.

b. One end of the AC bus access junction box into power grid.

c. Wire the conductors of the AC bus: L - BROWN; N - BLUE.

NOTE: Wiring colour code can be different according local regulation, check all the wires of the

installation before connecting to the AC bus to be sure they match.Wrong cabling can damage

irreparably the microinverters, such an issue is not covered by the warranty.

Step 3. Attach the APsystems Microinverters to the racking

NOTE: Do not place the microinverters (including DC and AC connectors) where exposed to the

sun, rain or snow, even gap between modules. Allow a minimum of 3/4’’(1.5cm.) between the roof

and the bottom of the microinverter to allow proper air flow.The racking of install microinverter

must be reliably grounding.

d. Mark the location of the microinverter on the rack, with respect to the PV module

junction box or any other obstructions.

e. Mount one microinverter at each of these locations using hardware recommended

by your module racking vendor.when install microinverter, grounding washer

Must be facing the racking.

Step 4. Ground the system.

Step 5. Connect the APsystems Microinverter to AC bus cable

Push the microinverter AC connector to the trunk cable connector. Listen for the "Click".

Please scan the QR code to get

mobile app and more support

to help the installation.

Click

Power grid

Best Practice: Use the Bus

Cable Unlock Tool of AC

Bus to split the connectors.

grounding washer

2018/07/26 Rev1.0 Quick Installation Guide

NOTE: AC connector interface as follows.

Step 6. Install a Bus Cable End Cap at the end of AC bus cable.

a. Strip cable jacket. c. Insert the wires into the cable clamps.

b. Insert the cable end into the seal. d. Rotate the nut with 3.3N·m until the

latching mechanism meets the base.

Step 7. Place the PV modules and connect each QS1 to the PV modules

Step 8. Complete the APsystems installation map

a. Each APsystems Microinverter has removable serial number labels.

b. Peel labels off, affix one to the respective location on the APsystems installation map,and fill

in 1,2 in the label below,according to the layout on the roof..

c. The other one serial number label, posted on the solar module frame is easy to view the

position.

d. After the completion of installation drawings sent to APsystems website.

www.APsystems.com.

NOTE: Sequence of steps 1~8 can change for convenience of installation.

NOTE: Using APsystems' mobile app ArrayApp can make the installation and registration much

more simple.

Step 9. Start the operation

1. Turn on the AC circuit breaker on each microinverter AC branch circuit.

2. Turn on the main utility-grid AC circuit breaker. Your system will start producing.

power after a two-minute waiting time.

Product information is subject to change without notice.(Please download manuals at www.APsystems.com).

Nut

Seal

Body

NOTE: Cover any unused connectors with Bus

Cable Y-CONN Cap to protect the connectors.

NOTE: If the DC connector is not connected with the PV module,you

need to remove the dust cap,and cover the protection cap.

Table des matières

Autres manuels APsystems Onduleur

APsystems

APsystems QT2 Manuel utilisateur

APsystems

APsystems YC600 Mode d’emploi

APsystems

APsystems YC500i Series Mode d’emploi

APsystems

APsystems YC1000-3 Series Manuel utilisateur

APsystems

APsystems YC1000-3-ZA Manuel utilisateur

APsystems

APsystems DS3D Manuel utilisateur

APsystems

APsystems YC500A-EU Manuel utilisateur

APsystems

APsystems YC1000-3-3 Manuel utilisateur

APsystems

APsystems DS3 Series Manuel utilisateur

APsystems

APsystems YC500 Mode d’emploi

APsystems

APsystems YC500A Mode d’emploi

APsystems

APsystems YC1000-3-208 Mode d’emploi

APsystems

APsystems QT2-AU Manuel utilisateur

APsystems

APsystems QS1-EU Manuel utilisateur

APsystems

APsystems YC500I-EU Manuel utilisateur

APsystems

APsystems QS1 Manuel utilisateur

APsystems

APsystems QS1 Manuel utilisateur

APsystems

APsystems YC500A Manuel utilisateur

APsystems

APsystems QT2 Manuel utilisateur

APsystems

APsystems DS3-S Manuel utilisateur

APsystems

APsystems QT2 Manuel utilisateur

APsystems

APsystems QS1 Manuel utilisateur

APsystems

APsystems DS3 Series Manuel utilisateur

APsystems

APsystems QS1 Manuel utilisateur

Manuels Onduleur populaires d'autres marques

Fourgroup

Fourgroup Easy Manuel utilisateur

Velleman

Velleman PI300M Manuel utilisateur

Sungrow

Sungrow SG350HX-US Manuel utilisateur

WilTec

WilTec 61897 Manuel utilisateur

SMA

SMA SUNNY BOY STORAGE 2.5 Manuel utilisateur

Simplicity

Simplicity LANDLORD 316 Manuel utilisateur

Santak

Santak SMAX 3000 Manuel utilisateur

ATON

ATON RA.Store-3 Manuel utilisateur

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuel utilisateur

Tektronix

Tektronix CFG250 Manuel utilisateur

Champion

Champion 200989 Manuel utilisateur

Vanner

Vanner 20-500 Series Manuel utilisateur

GE GEP Manuel utilisateur

Astrel Group

Astrel Group Power Reducer Guide rapide

MULTIQUIP

MULTIQUIP GDP-5H Mode d’emploi

GoWISE

GoWISE PS1007 Manuel utilisateur

Promate

Promate PM13500D ES Manuel utilisateur

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuel utilisateur