APsystems YC1000-3 Series Manuel utilisateur

REV1.2 Quick Installation Guide

1

APsystems YC1000-3-EU Microinverter Quick Installation Guide

The sketch of YC1000-3 support system.

All the solar panels are placed into two lines. Then put a YC1000-3 in the middle of the two lines and make

sure it is easy to connect with to four panels which are next to it, as well all the cables.

Step 1. Verify the grid voltage to match with microinverter rating.

Step 2. Lay the AC bus according to the arrangement of APsystems Microinverter.

Step 3. Attach the APsystems Microinverters to the racking.

Step 4. Attach the antenna to the microinverter, and keep the antenna vertical to the

earth.

Step 5. Connect the APsystems Microinverter cables to the AC bus cable.

NOTE: AC connector interface as follows, NOTE: Cover all unused T connectors with

from left to right PE, N, L3, L2, L1. sealing caps to protect the T connectors.

REV1.2 Quick Installation Guide

2

Step 6. Place the PV modules and connect each YC1000 to four PV modules close-by.

CH4 CH3 CH2 CH1

Step 7. Install a protective end cap at the end of AC bus cable.

a．Wire stripping

b．Insert the cable end into the gasket clamp.

c．Insert five wires into five cable clamps.

d．Rotate the nut with 2.5N·m until the latching

mechanism meets the base.

Step 8. Install the AC branch circuit junction box.

Step 9. Connect the cables to the branch junction box.

a. Put the unused end of the AC interconnector cable into the branch junction box.

b. Place cable connecting to the point of load interconnection into the branch junction box.

c. Wire the conductors: BROWN-L1; BLACK -L2; GRAY-L3; LIGHT BLUE-N; YELLOW GREEN-PE.

Step 10. Complete the APsystems installation map.

Each APsystems microinverter has two removable serial number labels. Peel labels off, affix one to the

respective location on the APsystems installation map, and affix another to the PV module frame which is

easy to see. Use the Scanning Gun to scan the serial numbers on the map into the computer or scan by

mobile phone, then complete the setting (see ECU manual).

NOTE: Step 1~10 can change sequence for convenience of installation.

Step 11. Start the operation.

1. Turn on the AC circuit breaker on each microinverter AC branch circuit.

2. Turn on the main utility-grid AC circuit breaker. Your system will start producing power after a

five-minute waiting time.

Product information is subject to change without notice.

(Please download manuals at www.APsystems.com).

Nut

Gaske Clamp

Body

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels APsystems Onduleur

APsystems

APsystems YC500A-NA-MX Mode d’emploi

APsystems

APsystems QT2 Manuel utilisateur

APsystems

APsystems EZ1 Series Manuel utilisateur

APsystems

APsystems YC600B Manuel utilisateur

APsystems

APsystems YC1000-3-208 Mode d’emploi

APsystems

APsystems YC600 Manuel utilisateur

APsystems

APsystems YC500I-EU Manuel utilisateur

APsystems

APsystems YC500A Mode d’emploi

APsystems

APsystems YC500i Series Mode d’emploi

APsystems

APsystems QS1A Manuel utilisateur

APsystems

APsystems YC500A-EU Manuel utilisateur

APsystems

APsystems YC500A Mode d’emploi

APsystems

APsystems YC500 Mode d’emploi

APsystems

APsystems YC500A Manuel utilisateur

APsystems

APsystems QS1 Manuel utilisateur

APsystems

APsystems QT2 Manuel utilisateur

APsystems

APsystems YC1000-3-208 Mode d’emploi

APsystems

APsystems YC600 Manuel utilisateur

APsystems

APsystems YC1000-3-NA Manuel utilisateur

APsystems

APsystems YC600 Manuel utilisateur

APsystems

APsystems QS1-LK Manuel utilisateur

APsystems

APsystems YC500I-ZA Manuel utilisateur

APsystems

APsystems DS3D Manuel utilisateur

APsystems

APsystems QS1 Manuel utilisateur

Manuels Onduleur populaires d'autres marques

Fourgroup

Fourgroup Easy Manuel utilisateur

Velleman

Velleman PI300M Manuel utilisateur

Sungrow

Sungrow SG350HX-US Manuel utilisateur

WilTec

WilTec 61897 Manuel utilisateur

SMA

SMA SUNNY BOY STORAGE 2.5 Manuel utilisateur

Simplicity

Simplicity LANDLORD 316 Manuel utilisateur

Santak

Santak SMAX 3000 Manuel utilisateur

ATON

ATON RA.Store-3 Manuel utilisateur

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manuel utilisateur

Tektronix

Tektronix CFG250 Manuel utilisateur

Champion

Champion 200989 Manuel utilisateur

Vanner

Vanner 20-500 Series Manuel utilisateur

GE

GE GEP Manuel utilisateur

Astrel Group

Astrel Group Power Reducer Guide rapide

MULTIQUIP

MULTIQUIP GDP-5H Mode d’emploi

GoWISE

GoWISE PS1007 Manuel utilisateur

Promate

Promate PM13500D ES Manuel utilisateur

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manuel utilisateur