Appostar FP-4266 Manuel utilisateur

Wall Mount POS Terminal

FP-4266

User’s Manual



Edition: Jan 2015 Version 1.0

http://www.appostar.com

PREFACE

2 FP-4266 Wall Mount POS Terminal



Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Declaration of Conformity

These devices comply with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. These devices may not cause harmful interference.

2. These devices must accept any interference received, including interference

that may cause undesired operation.

Lithium Battery Replacement

To avoid possible danger of explosion, ensure correct polarity when changing the

lithium battery. Replace only with the same or equivalent type recommended by

the manufacturer.

WEEE (Waste from Electrical and Electronic Equipment)

The WEEE wheeled bin symbol on the product or on its packaging indicates that

the product must not be disposed of with other waste. It should be the user’s

responsibility to dispose of their waste equipment by handing it over to an

approved location for the recycling of waste electrical and electronic equipment.

For more information about where to send your waste equipment for recycling,

please contact your local city office, your household waste disposal service or

where you purchased the product.

  

PREFACE

FP-4266 Wall Mount POS Terminal  3



Disclaimer

The material in this document is for information purpose and is subject to change

without prior notice. APPOSTAR has made every effort to ensure that this user’s

manual is accurate and complete. However, no liability is assumed for any errors

and omissions that may have occurred. Nor are any liability assumed for any

damages resulting from the use of this product and the information contained in

this document. APPOSTAR reserves the right to make improvements to this

publication from time to time in the contents hereof without obligation of the

manufacturer to notify any person of such revision or changes.

This work is copyrighted. Reproduction or retransmission of this documentation,

in whole or in part, without prior written permission from the manufacture is a

violation of copyright law.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

2. Intel is a registered trademark of Intel International Inc.

3. Other software or product names used in this manual are the properties of

their respective owners and are acknowledged.

PREFACE

4 FP-4266 Wall Mount POS Terminal



SAFETY INSTRUCTIONS

Ignore these safety instructions may cause bodily injury, or damage to the

product. Read these instructions carefully and keep this user’s manual in an

accessible location for future reference.

1. Do not plug in or unplug the power cord with wet hands.

2. Do not plug the product into an AC outlet with the incorrect voltage.

(Be sure to use a voltage that is between AC 100V~240V)

3. Do not plug several products into one multi-outlet.

4. Do not apply pressure to the power cord or place heavy objects on it.

5. Immediately stop using the product if it emits strange noise, odor, or

smoke.

6. Do not use aerosol sprayers containing flammable gas inside or around

the product.

7. Do not allow foreign objects or liquids to enter the product, or serious

damage may result.

8. Do not place the product on an unstable surface. The product may cause

a fire if it is dropped, damaged, or broken.

The product may cause a fire or electric shock when it is used

improperly. Observe the safety measures at all times.

If the product is damaged, immediately turn off the power and

disconnect the power cord. Contact your dealer for assistance.

The following instructions will help you to make better use of this product.

1. Keep the machine away from locations subject to high humidity, dust, or

temperatures that exceed the specification. (Refer to SEC. 1.4

Specification)

2. Clean the product only by using a dry cloth or a cloth soaked with

detergent. Never use thinner or other volatile solvents for cleaning.

3. At the end of the day, clean and inspect the exterior of the machine after

the machine is powered off.

4. Use only specified accessories.

5. Do not expose the accessories directly to sunlight, high temperatures,

humidity, dust, or gas.

6. Do not place heavy objects on top of the product or lean them against the

product. These items may fall down and cause injury.

7. Do not block the air vent of the product as this can cause heat

accumulation inside the box machine and may cause a fire.



FP-4266 Wall Mount POS Terminal  5



Table of Contents



CHAPTER 1 PRODUCT OVERVIEW ...........................................6

1.1 UNPACKING ..........................................................................................6

1.2 APPEARANCE.........................................................................................7

1.3 I/O INTERFACE......................................................................................8

1.4 SPECIFICATION......................................................................................9

CHAPTER 2 HARDWARE INSTALLATION ...............................10

MAGNETIC STRIPE READER (MSR) INSTALLATION ................................................ 10

CHAPTER 3 SOFTWARE INSTALLATION ................................11

3.1 MOTHERBOARD DRIVER INSTALLATION......................................................... 11

3.2 TOUCH DRIVER INSTALLATION .................................................................. 13

CHAPTER 4 BOARD SETTING.................................................15

MAIN BOARD JUMPER SETTING....................................................................... 15

CHAPTER 5 TROUBLESHOOTING...........................................17

HARDW

6



CHA

Welc

The FP

power c

series in

value. T

1.1 U

Confirm

missin

1. PO

(User’s

RE INSTAL

TER

eries is t

nsumpti

cludes e

e main

packin

that all t

or dama

Termina

4. Driver

Manual i

ATION

e wall-m

n to me

y savi

oard is s

e followi

ed, cont

l Main Un

cluded)

DUC

ount PO

t the tre

, low n

illfully e

items

ct the de

it 2





OVE

Termina

d for

oise ope

bedded

re conta

aler from

. Power

FP-

VIE

l which is

en produ

ation and

in the sli

ined in t

whom y

dapter

266 Wall

concept

t. The fe

h cos

touch

e carton.

u purcha

ount PO

alized to

atures of

-perfor

onitor.

If any it

sed the

. Power

Terminal

save

the FP

ance

m is

roduct.

ord

HARDWARE INSTALLATION

FP-4266 Wall Mount POS Terminal  7



1.2 Appearance

Front View



Rear View



15” Touch LCD

MSR module (optional)

/Attachable on both sides

I/O Cover

MSR Cover

HARDW

8



1.3 I/

NOTE:

RE INSTAL

Inter

Port

AKE

ER-INPUT

ER-OUTPUT

-OUT

PORT

With the

the slot.

ATION

ace

1W x 2

Power

12V DC

DB15 /

USB 2.

LAN po

To avoid

with cov

removabl

escription

N/OFF swi

JACK

Jack

F for 2nd di

Type A x

t with RJ4

confusio

. Remo

e bracket



play

with th

e the co

, the HD

FP-

COM 1

COM 2

COM 4

Storage

COM 5

CASH DR

LAN por

er befor

/ SSD c

266 Wall

WER

, the CO

use.

n be eas

ount PO

Descri

ial port wit

D or SSD r

ial port wit

1 with 12V

2 is pr

ily replac

Terminal

tion

DB9/M

RJ45

DB9/M

movable

DB9/M

tected

d from

HARDWARE INSTALLATION

FP-4266 Wall Mount POS Terminal  9



1.4 Specification

Model Name FP-4266

System

Main Board IAT1-2550

CPU Intel Atom D2550 1.86 GHz Dual Core

Chipset Intel NM10 Express

Main Memory 1GB DDRIII RAM

Display Size 15” TFT-LCD with touch panel

Display Resolution 1024 x 768

Touch Panel 5 wire resistive touch

HDD 2.5” SATA HDD 320G

Expansion slot 1 x Mini PCIe

OS Support POSReady 2009, POSReady7, Windows XP / XPE,

Windows 7, Windows 8, Linux

Power AC 100V~240V / 60W Power Adapter

External I/O Interface

Serial Port 4 x External COM Ports with 5V /12V selectable

Cash Drawer Port 1 x RJ11 with DC 12V (Standard / 24V)

VGA Port 1 x VGA (DB15)

Speaker 2 x Integrated 1W stereo speaker

Ethernet Port 1 x RJ45 10M / 100M /1GB Base-T

USB Port 4 x USB 2.0 Type A

DC Input Jack 1 x 12V / 5A

DC Output 1 x 12V / 2.5A

Power Button 1 x power on / off switch

Optional Peripheral

Magnetic Card Reader ISO 7811 option 1 / 2 / 3 track

i-Button Dallas Key

Wireless LAN 802.11 b/g

Environment

EMC & Safety CE / FCC Class A

Operating Temperature 5°C ~ 40°C

Storage Temperature -20°C ~ 60°C

Operating Humidity 15% ~ 80% RH

Storage Humidity 20% ~ 90% RH

Mechanical

Housing Color Black

Construction ABS + SECC

Dimension(W x D x H) 350 x 242 x 320 mm

Weight (N.W.) 5.8 kg

HARDW

10



CHA

Before s

off and

An optio

By defa

Step 1

Step 2

Step 3

RE INSTAL

TER

tartin

he powe

tic Stri

nal MSR

lt, the M

emove t

onnect t

ix the M

ATION

y hardw

cord is

pe Rea

an be in

R is inst

e cover

e MSR c

R modul

DWA

re confi

isconnec

er (M

talled on

lled on t

rom the

ble corr

in positi



RE IN

uration,

ed to pr

R) Ins

both the

e ri

ht s



SR exte

ctly.

n with 2

FP-

STAL

nsure th

vent pos

allatio

ht an

ide.

sion slot

screws.

266 Wall

ATI

t the sys

ible dam

left side



ount PO

tem is p

e to th

of FP-42

Terminal

wered

product

Table des matières

Autres manuels Appostar Terminal tactile

Appostar

Appostar KP-5562 Manuel utilisateur

Appostar

Appostar GP-3472 Manuel utilisateur

Appostar

Appostar KP-5372 Manuel utilisateur

Appostar

Appostar KP-5360 Manuel utilisateur

Appostar

Appostar KP-5660 Manuel utilisateur

Appostar

Appostar BS-6500 Manuel utilisateur

Appostar

Appostar KP-5374 Manuel utilisateur

Appostar

Appostar NP-3262 Manuel utilisateur

Appostar

Appostar KP-5362 Manuel utilisateur

Appostar

Appostar SP-7260 Manuel utilisateur

Appostar

Appostar KP-5360 Manuel utilisateur

Appostar

Appostar GP-3460 Manuel utilisateur

Appostar

Appostar Grand POS GP-3464 Manuel utilisateur

Appostar

Appostar KP-5370 Manuel utilisateur

Appostar

Appostar KP-5374 Manuel utilisateur

Appostar

Appostar Grand POS GP-3460 Manuel utilisateur

Appostar

Appostar KP-5660 Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur