Apogee BIG BEN Manuel d'utilisation

On this ﬁrst page we will deal with connecting Big Ben to a Pro Tools HD rig without using a Sync I/O.

The next page deals with connecting with the Sync I/O.

1) Connect a 75 ohm BNC cable between the WC Out connections of Big Ben and the EXT In of each

audio interface. (as shown below)

2) Do NOT connect the LOOP Sync connections between the audio interfaces. To best take advantage of

Big Ben’s superior clock, each interface must be connected directly to a Big Ben word clock output.

Using Big Ben with Pro Tools (without a Sync I/O)

1) Determine the desired sample rate for

the entire HD system, and set Big Ben

to that Sample rate.

2) In Pro Tools software, Session>Setup>

Click on the “Clock Source” ﬁeld, select

the ﬁrst audio interface, and set its clock

source to “Word Clock”

3) Repeat Step 2 for all audio interfaces.

Note that selections made for previous

interfaces will not be checked; this is

normal.

4) Verify on the front panel of each audio

interface that Sync Mode is set to EXT.

Send a separate W/C Out of

the Big Ben to the W/C In on

each interface. Once again,

Do NOT use Loop Sync!

APOGEE Connects:

Using the Big Ben with a Sync I/O

When using a SYNC I/O with a Big Ben, we ﬁnd it best to make the SYNC I/O the master and have the Big

Ben lock to it. The Big Ben can then send its superior clock out to all of your audio interfaces. In the example

below we are using 192’s. However the setup would be the same if you were using AD and DA-16X’s or

Rosetta’s connected via the X-HD option card. The only difference would be that the set up in Pro Tools is a

bit simpler, as explained on Pg. 3 of this document.

1) Connect a 75 ohm BNC cable from Word Clock out of the Sync I/O to the Word Clock In of the Big

Ben

2) Connect a 75 ohm BNC cable between the WC Out connections of Big Ben and the EXT In of each

audio interface.

3) Do NOT connect the LOOP Sync connections between the audio interfaces or to the SYNC I/O. To best

take advantage of Big Ben’s superior clock, each interface must be connected directly to a Big Ben word

clock output.

W/C Out of the Sync I/O to

W/C In on the Big Ben. Do

NOT use Loop Sync out!

Send a separate W/C Out of

the Big Ben to the W/C In on

each interface. Once again,

Do NOT use Loop Sync!

APOGEE Connects:

1) In Pro Tools under “Set Up”> “Session”>”Clock Source”> “192 I/O #1, choose “Word Clock”

You will get a message that says “The Sync I/O clock reference is not locked” Click on the OK button.

2) Now do the same for the remaining 192’s

3) Next, under “Clock Source” you will select “Sync I/O”

4) You should now see a message that says “The Sync I/O clock reference is now locked”

If you are using Apogee converters (AD/DA-16X’s or Rosetta’s via the X-HD card) and you are not using

192’s at all, you will not have to do the following previous 4 steps. The Apogee units will automatically

lock to external W/C when the Sync I/O is set to master.

APOGEE Connects:

Autres manuels pour BIG BEN

Autres manuels Apogee Matériel informatique

Apogee

Apogee DA-12 Manuel utilisateur

Apogee

Apogee AD-8000 Supplément

Apogee

Apogee X-Video Card Manuel utilisateur

Apogee

Apogee UV22HR Guide d'installation

Apogee

Apogee Symphony 64 Manuel utilisateur

Apogee

Apogee AMBus HD Manuel utilisateur

Apogee

Apogee X-Video Card Manuel utilisateur

Apogee

Apogee X-HD Manuel utilisateur

Apogee

Apogee X-FireWire Card Manuel utilisateur

Apogee

Apogee X-HD Manuel utilisateur

Apogee

Apogee Mini-Me Manuel utilisateur

Apogee

Apogee X-Digi-Mix Card Manuel utilisateur

Apogee

Apogee Mini-Series FireWire Manuel utilisateur

Apogee

Apogee AMBus Manuel utilisateur

Apogee

Apogee UV-1000 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur