Apera Instruments LabSen 801 Manuel utilisateur

LabSen 801 Pure Water Combination pH Electrode

User Manual

LabSen electrochemical sensors are premium pH electrode with manufacturing technology and key

components imported from Switzerland. LabSen801 pH electrode is suitable for pure water

measurement, such as drinking water, distilled water etc.

This probe has following features:

⚫ Impact-resist membrane (see the right picture), there is no danger of

electrode breakage during normal use.

⚫ Movable sleeve, able to adjust infiltration rate of electrolyte.

⚫ Blue gel inner solution, does not flow and will not cause bubble.

⚫ Silver ion trap reference prevents the contamination of the junction when

testing sample contains sulfides and proteins, which helps to improve the

stability and service life of the electrode.

1 Technical Data

Measuring Range

(0 ~ 11) pH

Electrolyte

3M KCl

Temperature Range

(0 ~ 80) °C

Soaking Solution

3M KCl

Shaft Material

Lead-free Glass

Membrane Resistance

<50MΩ

Membrane Type

Electrode Dimension

(Ø12×130) mm

Reference

Silver Ion Trap

Connector

BNC

Junction

Movable Sleeve

Cable

Ø3×1m

2 How to Use the Movable Sleeve

As shown on the right picture, reference solution flows out of the small hole,

seeps through the tapered surface of movable sleeve. You may adjust the

degree of firmness when use, push up the movable sleeve to loose. If it is

too tight to push, please referring to the right picture: insert the probe into

the round tube (the accessory comes with the probe), and push down the

probe, then the movable sleeve will be loosen. Please pay attention to

remove the rubber plug when adjusting the movable sleeve, enables

reference solution flowing out of the small hole; then slowly rotate and

tighten the movable sleeve, so that there will be no air remain in the tapered

surface of movable sleeve, which can greatly influence the correct

measurement of the probe.

3 Usage and Maintenance

3.1 When measuring, please unscrew the bottle cap, pull out the electrode and

rinse it with deionized water. After using, please put the electrode back into the

bottle and screw tight the cap.

Before pulling out or putting back the electrode, make sure

to fully loosen the blue cap on the storage sleeve so that

the electrode can move in and out smoothly.

3.2 Prior to measurement, remove the rubber plug to maintain pressure of the reference solution,

keep consistent flow rate of reference solution and stable potentials of junction.

3.3 After a period of usage, the reference solution will be running low. Whenever the level falls to

1/2 height of the electrode, add 3M KCL solution to the refilling hole by using syringe or pipette.

3.4 Reference solution refilling in cases of contamination; pull out plastic plug, loosen movable

sleeve, Electrolyte will drops out quickly. After cleaned with 3M KCL solution, tighten glass

sleeve (see section 3), refill 3M KCL solution after washing cavity with pure water and 3M KCL.

Then loosen movable sleeve and slowly twist it tighten, to avoid air remain in the tapered surface

of movable sleeve.

3.5 Drop speed of reference solution decides by the glass sleeve tightness, the tighter the slower.

Electrodes must recalibrate upon tightness adjusted. For viscous or low ion concentration

solution measuring, requires fast speed.

3.6 The connector of the electrode should keep clean and dry. If being contaminated, please clean

it with medical cotton and absolute alcohol and blow dry to prevent the short circuit of the

electrode and slow reaction of electrode.

3.7 The electrode’s measuring tip should be soaked in the soaking bottle containing certain amount

of storage solution to keep the membrane hydrated and junction unblocked. Clean the bottle

and replace the storage solution if the storage solution gets turbid and mildewed. The electrode

should never be sinked in pure water or buffer solution for long.

3.8 After 1-year of use, we recommend replacing the electrode to ensure the best accuracy.

4 Warranty

We warrant this electrode free from defects in material and workmanship and agrees to repair or

replace free of charge, at option of APERA INSTRUMENTS any malfunctioned or damaged product

attributable to responsibility of APERA INSTRUMENTS for a period of six months. Warranty period

is the time limit to provide free service for the products purchased by customers, not the service life

of the tester or electrodes.

This limited warranty does not cover any damages due to:

transportation; storage; improper use; failure to follow the product instructions or to perform any

preventive maintenance; modifications; combination or use with any products, materials, processes,

systems or other matter not provided or authorized in writing by us; unauthorized repair; normal wear

and tear; or external causes such as accidents, abuse, or other actions or events beyond our

reasonable control.

APERA INSTRUMENTS (Europe) GmbH

Address: Wilhelm-Muthmann-Str.18,

42329 Wuppertal, Germany

Phone: +49 202 51988998

Website: www.aperainst.de

Email: info@aperainst.de

Table des matières

Autres manuels Apera Instruments Instrument de mesure

Apera Instruments

Apera Instruments MP511 Manuel utilisateur

Apera Instruments

Apera Instruments SX811-BS Manuel utilisateur

Apera Instruments

Apera Instruments YD300 Manuel d'instructions

Apera Instruments

Apera Instruments Gro Star AI102G Manuel utilisateur

Apera Instruments

Apera Instruments DO8500 Manuel utilisateur

Apera Instruments

Apera Instruments PC60 Manuel utilisateur

Apera Instruments

Apera Instruments PC 8500 Manuel utilisateur

Apera Instruments

Apera Instruments SX736 Manuel utilisateur

Apera Instruments

Apera Instruments 2301T-S Manuel utilisateur

Apera Instruments

Apera Instruments DO803 Manuel utilisateur

Apera Instruments

Apera Instruments LabSen 211 Manuel utilisateur

Apera Instruments

Apera Instruments LabSen 861 Manuel utilisateur

Apera Instruments

Apera Instruments TN420 Manuel utilisateur

Apera Instruments

Apera Instruments PH400 Manuel utilisateur

Apera Instruments

Apera Instruments SX811-PW Manuel utilisateur

Apera Instruments

Apera Instruments PH60 Manuel utilisateur

Apera Instruments

Apera Instruments LabSen 751 Manuel utilisateur

Apera Instruments

Apera Instruments TN500 Manuel utilisateur

Apera Instruments

Apera Instruments SX751 Manuel utilisateur

Apera Instruments

Apera Instruments 2401T-F Manuel utilisateur

Apera Instruments

Apera Instruments PHB-3 Manuel utilisateur

Apera Instruments

Apera Instruments SX823-B Manuel utilisateur

Apera Instruments

Apera Instruments PH60Z-MS Manuel utilisateur

Apera Instruments

Apera Instruments WS100 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur