Antec EA-430D Green Manuel utilisateur
EA-430D GREEN
POWER SUPPLY
USER’S MANUAL
USER’S MANUAL
EARTHWATTS SERIES
EA-430D GREEN POWER SUPPLY
THE ENERGY-EFFICIENT PSU
Get the power you need and the low electric bill you want with Antec’s EA-430D Green! One of the most
environmentally friendly power supplies on the planet, the EA-430D Green delivers 430 watts of reliable,
continuous power while meeting the Bronze level of performance from 80® PLUS, the most widely
recognized independent standard in power supply efficiency.
STANDARDS AND FEATURES
The EA-380D Green PSU is compatible with ATX12V v2.3 and EPS12V v2.91 specifications. This PSU
features Universal Input, which automatically senses when you connect the power supply to any AC
power source between 100 ~ 240V, eliminating the need to set a voltage switch. The EA-380D Green
also features Active Power Factor Correction (Active PFC), which improves the power factor value of the
PSU by altering the input current wave shape, helping to transmit energy across the grid.
SYSTEM PROTECTION
A variety of industrial-grade safety circuitry will help protect your computer: OVP (Over Voltage
Protection), SCP (Short Circuit Protection), and OCP (Over Current Protection). Sometimes the PSU will
“latch” into a protected shutdown state. This means that you will need to power off the PSU and clear
the fault before it will function again. There are no user-replaceable fuses in your EA-430D Green.
TABLE 1: OCP SET POINT
Rail
+3.3V OCP
+5V OCP
+12V OCP
(Per rail)
Max. A
31A
36A
27A
80 PLUS® BRONZE CERTIFICATION
80 PLUS® Bronze certification is among the highest independent standards in power supply efficiency.
This allows the PSU to use less energy and generate less heat so it stays cooler, runs more quietly, and
lasts longer. The EA-430D Green has been certified to be at least 82% efficient at a wide range of
operating loads and will lower your operating costs while protecting the environment.
Source: 80 PLUS Verification and Testing Report
DUAL +12 VOLT RAIL DISTRIBUTION
The EA-430D Green PSU uses dual +12 volt power rails. Different connectors are hooked up to separate
circuits to aid in the balanced distribution of power between devices in your computer. The engineers
have allocated the rails to different connectors, as shown in Table 2, to prevent voltage sags in one
device due to sudden demands for power by another device.
TABLE 2: POWER CONNECTORS AND RAIL ASSIGNMENTS
Power Connectors
Description
+12V Rail
24-pin (20+4) main connector
1
4+4 pin ATX12V / EPS12V
2
6-pin PCI-E connector
1
4 x Molex
1
5 x SATA
1
1 x Floppy
1
Note: No power cord included. By reusing your existing cord, you can reduce waste and help protect the
environment.
POWER OUTPUT
The EA-430D Green PSU distributes a varying maximum number of amps on each rail. To see the output
capacity and regulation for each different voltage, see Table 3.
TABLE 3: OUTPUT CAPACITY AND REGULATION
Output
Voltage
Load Max.
Regulation
Ripple & Noise
+3.3V
20A
±5%
50 mV
+5V
20A
±5%
50 mV
+12V1
17A
±5%
120 mV
+12V2
16A
±5%
120 mV
–12V
0.8A
±10%
120 mV
+5VSB
2.5A
±5%
50 mV
The continuous maximum total output power shall not exceed 430W.
+12V1 and +12V2 DC maximum output power shall not exceed 384W.
+3.3V and +5V DC maximum combined output power shall not exceed 115W.
INSTALLATION:
1. Install the EA-430D Green PSU into your case with the four screws provided.
2. Connect the 24-pin main power connector to your motherboard. If your motherboard uses a 20-
pin connector, detach the 4-pin attachment on the 24-pin connector.
Note: The detachable 4-pin section cannot be used in place of a 4-pin +12V connector.
3. Connect the 8-pin or 4-pin ATX12V connector for the CPU to the appropriate connector on your
motherboard. If your motherboard has an 8-pin socket with a cover on some of the openings,
we recommend that you remove the cover and use the 8-pin connector.
Note: Please also refer to your motherboard user’s manual for any special instructions.
4. Connect an AC power cord to the power supply AC inlet. To reduce waste, the EA-430D Green
does not come with a power cord. Turn the switch to the “|” position after you have connected
all the devices and are ready to turn on your computer.
Antec, Inc.
47900 Fremont Blvd.
Fremont, CA 94538
tel: 510-770-1200
fax: 510-770-1288
Antec Europe B.V.
Stuttgartstraat 12
3047 A Rotterdam
Netherlands
tel: +31 (0) 10 462-2060
fax: +31 (0) 10 437-1752
Technical Support:
US & Canada
1-800-22ANTEC
customersupport@antec.com
Europe
+31 (0) 10 462-2060
europe.techsupport@antec.com
www.antec.com
© Copyright 2009 Antec, Inc. All rights reserved.
All trademarks are the property of their respective owners.
Reproduction in whole or in part without written permission is prohibited.
Table des matières
Autres manuels Antec Alimentation
Antec
Antec TRUEPOWER TP2-550EPS12V Manuel utilisateur
Antec
Antec TruePower Quattro 1200-Watt Manuel utilisateur
Antec
Antec CP-1000 Manuel utilisateur
Antec
Antec EARTHWATTS EA-650 Manuel utilisateur
Antec
Antec EarthWatts EA-430 Green Manuel utilisateur
Antec
Antec HCG-620 Manuel utilisateur
Antec
Antec VP350P Manuel utilisateur
Antec
Antec PHANTOM 350 Manuel utilisateur
Antec
Antec NeoPower 650 Blue Manuel utilisateur
Antec
Antec TruePower Quattro 1000W Manuel utilisateur
Antec
Antec New Solution Series NSK 1480 Manuel utilisateur
Antec
Antec PowerUp 6000 Manuel utilisateur
Antec
Antec TRUEPOWER TP-650 Manuel utilisateur
Antec
Antec NSK2400 Manuel utilisateur
Antec
Antec HCP-850 Manuel utilisateur
Antec
Antec Neo ECO Series Manuel utilisateur
Antec
Antec Veris Fusion 430 Manuel utilisateur
Antec
Antec HCP-850 Manuel utilisateur
Antec
Antec TP-650C TRUEPOWER Classic Manuel utilisateur
Antec
Antec EARTHWATTS Manuel utilisateur
