Ankom TDF Guide de référence

Ash Determination Procedure –IDF/SDF/TDF

Rev 9/20/13

Pg. 1 of 2

Ash Determination

ANKOM Technology recommends that you use ceramic crucibles with fitted

covers to avoid cross contamination or loss of ash. Fold the filter bags so that they

easily fit into the crucibles.

IDF

To determine the ash content within the IDF residue, follow the procedure below.

Starting at the bottom of the filter part of the bag, fold the bag upward, leaving at least 10 mm at the top of the

clear polypropylene that is not folded. Then fold the bag in thirds from side to side.

With your Heat Sealer set to “6” (setting may vary depending on heat sealer and power source), press the Heat

Sealer arm down for 3 to 4 seconds to seal the clear polypropylene part of the bag just above the white filter

material.

Label the folded, sealed filter bag and place it in a labeled ashing crucible.

Repeat steps 1 –3 for all IDF bags to be ashed.

Place covered ashing crucibles with filter bags in a furnace at 600°C for 3 hours.

After the 3 hour furnace time, place the ashed crucibles in desiccator(s) and allow them to cool.

Remove cooled crucibles from the desiccator(s) and record their weights.

10 mm of clear

polypropylene

Ash Determination Procedure –IDF/SDF/TDF

Rev 9/20/13

Pg. 2 of 2

SDF / TDF

During a TDF procedure there is no residue captured in the IDF Flow-Thru bag.

Therefore, the ash procedure is only required for the SDF filter bag.

Diatomaceous Earth (DE) used in the precipitation process can sometimes be

difficult to fully rinse from the walls of the polypropylene bags. Therefore,

ANKOM Technology recommends that the entire SDF bag be ashed.

To determine the ash content within the SDF / TDF residue, follow the procedure below.

Starting at the bottom of the filter part of the bag, fold the bag upward, leaving at least 10 mm at the top of the

clear polypropylene that is not folded. Then fold the bag in thirds from side to side.

Set your Heat Sealer to “6” (setting may vary depending on heat sealer and power source) and press the Heat

Sealer arm down for 3 to 4 seconds to seal the unfolded polypropylene to the folded part of the bag.

Label the folded, sealed filter bag and place it in a labeled ashing crucible.

Repeat steps 1 –3 for all SDF bags to be ashed.

Place covered ashing crucibles with filter bags in a furnace at 600°C for 3 hours.

After the 3 hour furnace time, place the ashed crucibles in desiccator(s) and allow them to cool.

Remove cooled crucibles from the desiccator(s) and record their weights.

10 mm of clear

polypropylene

Autres manuels pour TDF

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ankom Instrument de mesure

Ankom

Ankom RF Manuel

Ankom

Ankom A2000 Manuel

Ankom

Ankom Flex Analyte Extractor Manuel utilisateur

Ankom

Ankom ANKOM200 FIBER ANALYZER Manuel utilisateur

Ankom

Ankom TDF Manuel utilisateur

Ankom

Ankom TDF Series Manuel

Ankom

Ankom A2000 Instructions d'utilisation et de sécurité

Ankom

Ankom A2000 Manuel

Ankom

Ankom TDF Series Manuel

Ankom

Ankom TDF Series Manuel

Ankom

Ankom Delta Manuel utilisateur

Ankom

Ankom A2000 Manuel

Ankom

Ankom 2000 Manuel utilisateur

Ankom

Ankom TDF28 Manuel

Ankom

Ankom TDF Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur