Ankom A2000 Manuel

Service Procedure # 002

(Page 1 of 3) 08/05/2014

Packing and Agitator Replacement

A2000/A2000I

ANKOM Technology 2052 O’Neil Road Macedon, NY 14502 PH: (315) 986-8090 FAX: (315) 986-8091

[email protected]

1. Place cardboard on a table. Lay the A2000 on

it’s front. Remove the nuts that secure the clear

back panel. Remove the panel. Remove the

feet and mounting screws, then remove the

bottom panel.

2. Loosen the top set screw on the coupler.

3. Loosen the packing nut until it is finger loose. 4. Remove the three nuts that secure the motor

bracket in place

5. Unplug the motor wires and set the motor out of

the way.

6. Twist and pull up to remove the agitator.

Service Procedure # 002

(Page 1 of 3) 08/05/2014

Packing and Agitator Replacement

A2000/A2000I

Check Agitator-

1. Check the agitator for wear and pitting in the shaft surface. The surface should be very smooth without grooves, pits or a

thinned diameter.

2. The agitator can be installed if the packing has not been disturbed. Push and twist until the agitator is completely seated on

the vessel bottom.

3. Replace the motor and cabinet bottom. Follow the procedure for tightening the packing on the bottom of page 3.

Note:

The Agitator Teflon

Collar must rest against

the bottom of the

Digestion Vessel when

installed.

Replacing the Packing-

1. The packing is removed using a screwdriver.

2. The packing consists of two carbon ropes and one compressed

graphite cylinder. When removed, it will look similar to the image

on the left. Ensure both ropes are removed or the new packing

will not fit.

(

ANKOM Technology 2052 O’Neil Road Macedon, NY 14502 PH: (315) 986-8090 FAX: (315) 986-8091

[email protected]

Service Procedure # 002

(Page 1 of 3) 08/05/2014

Packing and Agitator Replacement

A2000/A2000I

Packing

Bushing

Packing

Bushing

3. Check the packing nut after four hours of use and adjust if necessary. If assistance is needed, call

ANKOM Technology at 315-986-8090 or email technical service at [email protected].

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ankom Instrument de mesure

Ankom

Ankom A2000 Manuel

Ankom

Ankom Delta Manuel utilisateur

Ankom

Ankom TDF Series Manuel

Ankom

Ankom RF Manuel

Ankom

Ankom A2000 Instructions d'utilisation et de sécurité

Ankom

Ankom TDF28 Manuel

Ankom

Ankom Flex Analyte Extractor Manuel utilisateur

Ankom

Ankom 2000 Manuel utilisateur

Ankom

Ankom A2000 Manuel

Ankom

Ankom ANKOM200 FIBER ANALYZER Manuel utilisateur

Ankom

Ankom TDF Manuel utilisateur

Ankom

Ankom TDF Series Manuel

Ankom

Ankom TDF Series Manuel

Ankom

Ankom TDF Manuel utilisateur

Ankom

Ankom TDF Guide de référence

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur