Analog Devices DC456 Manuel utilisateur

LTC3412 DC456 Description

DC456 is a high efficiency, high frequency buck converter, incorporating

the LTC3412 monolithic synchronous regulator. The DC456 has an input

voltage range of 2.5V to 5.5V and an output voltage range from 0.8V to

5V. The operating frequency range of the DC456 is either set with an

external resistor or synchronized to an external clock, with a range

between 100 kHz and 1.5 MHz. Due to these features, the DC456 is ideal

for Li-Ion battery voltage (2.7V to 4.2V) applications, such as PDAs,

cellular phones, and digital cameras. The DC456 can deliver high(er)

power – up to 2A of output current – in a relatively small circuit, because

of the high current power switches (80 mΩof on-state resistance) on the

LTC3412. The LTC3412 also incorporates OPTI-LOOP compensation, so

that the DC456 can be optimized to provide fast transient response over a

wide range of line and load conditions. All these features make the

DC456 perfectly suited for battery-powered, hand-held applications.

Design files for this circuit are available. Call the LTC Factory.

LTC3412 DC456 Quick Start Guide

Demonstration circuit 456 is easy to set up to evaluate the performance of the

LTC3412. Please follow the procedure outlined below for proper operation.

1. Select the desired output voltage using jumpers JP1 thru JP4. The

fixed output voltages are 1.8V, 2.5V, and 3.3V (as shown). There is

also an option to set the output voltage to a custom value by inserting

a resistor into the R6 pads next to jumper JP4. Refer to figure 1 for the

proper circuit setup.

2. Connect the input power supply to the Vin and GND terminals on the

top right-side of the board. Do not hot-plug Vin or increase Vin over

the rated maximum supply voltage of 5.5V, or the part may be

damaged. Refer to figure 1 for the proper measurement equipment

setup.

3. Connect the load between the Vout and GND terminals on the bottom

right-side of the board.

4. Select the desired operating mode using J1. To select Force

Continuous mode, tie the SYNC/Mode pin to Vin by inserting the

jumper into the lower position. Inserting the jumper into the upper

position selects Burst Modeoperation.

5. To shut down the circuit, connect the Run pin to GND by inserting a

jumper into the upper position of J2.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Analog Devices Inc.:

DC456A

Table des matières

Autres manuels Analog Devices Carte mère

Analog Devices

Analog Devices EVAL-ADAQ7768-1 Manuel utilisateur

Analog Devices

Analog Devices AD8556-EVALZ Manuel utilisateur

Analog Devices

Analog Devices UG-474 Manuel utilisateur

Analog Devices

Analog Devices ADSP-BF592 EZ-KIT Lite Manuel utilisateur

Analog Devices

Analog Devices ADP5140-EVALZ Manuel utilisateur

Analog Devices

Analog Devices MAX17625 Manuel utilisateur

Analog Devices

Analog Devices ADSP-SC589 EZ-Board Manuel utilisateur

Analog Devices

Analog Devices EV-ADF4156SD1Z Manuel utilisateur

Analog Devices

Analog Devices LINEAR TECHNOLOGY LTC2874 Guide de configuration rapide

Analog Devices

Analog Devices ADSP-21161N Manuel utilisateur

Analog Devices

Analog Devices EVAL-AD7606BFMCZ Manuel utilisateur

Analog Devices

Analog Devices EVAL-AD5600PMDZ Manuel utilisateur

Analog Devices

Analog Devices DC981A Guide de configuration rapide

Analog Devices

Analog Devices ADPA1107-EVALZ Manuel utilisateur

Analog Devices

Analog Devices EVAL-AD5933EBZ Manuel utilisateur

Analog Devices

Analog Devices EVAL-AD7175-8SDZ Manuel utilisateur

Analog Devices

Analog Devices UG-061 Manuel utilisateur

Analog Devices

Analog Devices ADD8754-EVAL Manuel utilisateur

Analog Devices

Analog Devices EVAL-AD5142ADBZ Manuel utilisateur

Analog Devices

Analog Devices DC3186A Guide de configuration rapide

Analog Devices

Analog Devices ADN2841 Instructions d'installation et d'utilisation

Analog Devices

Analog Devices EV-SC594-SOM Manuel utilisateur

Analog Devices

Analog Devices Linear Technology 2658A Guide de configuration rapide

Analog Devices

Analog Devices EVAL-AD4114 Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur