Analog Devices Linear ADI Power DC3091 Manuel utilisateur

DEMO MANUAL DC3091A

Rev. 0

DESCRIPTION

LTC3312SA

3.3V to 1.2V and1.8V at 6A, 2MHz Dual

Step-Down DC/DC Regulators

Demo Circuit 3091A features the LT C

3312SA, 5V, dual

6A/dual-phase 12A step-down DC/DC regulator IC. This

demo circuit is configured as a 2MHz, 3.3V input buck

regulator with dual 6A output at 1.2V and 1.8V.

The LTC3312SA features dual monolithic synchronous 6A

step-down power stages in a 3mm × 4mm package for

space saving applications with demanding performance

requirements. Both bucks achieve high efficiency and

fast transient response with small external components.

The LTC3312SA can also be configured as a single out-

put, dual-phase 12A step-down converter. Please refer

to DC3092A as a single output dual-phase application

example. The LTC3312SA data sheet gives a complete

description of its operation and application information.

All registered trademarks and trademarks are the property of their respective owners.

PERFORMANCE SUMMARY

The data sheet must be read in conjunction with this demo

manual when evaluating or modifying this demo circuit.

DC3091A supports three operation modes, including

pulse skip, forced continuous and Burst Mode

operation.

The clock frequency and the operation mode are shared by

both regulators. User can select desired operation mode

with JP1 jumper. Setting JP1 to FC/SYNC position also

allows the LTC3312SA to sync to a clock frequency from

1MHz to 3MHz, operating in forced continuous mode.

An EMI filter is included in this demo circuit for noise

sensitive applications. To power with EMI filter, please

apply input voltage via VIN EMI terminal.

Design files for this circuit board are available.

Specifications are at TA= 25°C

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS

VIN/VIN EMI DC3091A Input Voltage Range 2.25 5.5 V

VOUT1 DC3091A Output 1 Voltage Range 1.174 1.2 1.226 V

VOUT2 DC3091A Output 2 Voltage Range 1.755 1.8 1.843 V

IOUT DC3091A Output Current (Each Output) 6 A

fSW Switching Frequency 1.8 2.2 MHz

EFF1 Output1 Efficiency VIN = 3.3V, IOUT = 3A,VOUT1 = 1.2V 92 %

EFF2 Output2 Efficiency VIN = 3.3V, IOUT = 3A,VOUT2 = 1.8V 94 %

DEMO MANUAL DC3091A

Rev. 0

QUICK START PROCEDURE

Refer to Figure2 for the proper measurement equipment

setup and follow the procedure below:

NOTE:For accurate V

, V

OUT

and efficiency measure-

ments, measure VIN at the VIN SNSE and GND SNSN tur-

rets, and measure VOUT at the VOUT SNSE and GND SNSE

turrets. When measuring the input or output ripple, care

must be taken to avoid a long ground lead on the oscillo-

scope probe. It is recommended to use technique shown

in Figure3a and Figure3b for basic ripple measurement.

Prepare for the Test

A. Select a power supply PS1 that can handle 5V of output

voltage and 10A of output current, with internal current

meter. If possible, connect PS1 Kelvin Sense terminals

with VIN SNSE and GND SNSE turrets.

B. Select two electronic loads LD1 and LD2 that can han-

dle 2V of load voltage and up to 6A of load current in

constant current mode.

C. Select an oscilloscope with two or more channels and

two voltage probes.

BOARD PHOTO

Figure1. DC3091A Demo Board

DEMO MANUAL DC3091A

Rev. 0

QUICK START PROCEDURE

Test BUCK1 (VOUT1)

1. Connect PS1, LD1, VM1, VM2 and VM3 as shown in

Figure2. If the input EMI ﬁlter is desired, connect the

input power supply to VIN EMI and GND.

2. Set the JP2 to HI position. Set LD1 to 0A. Slowly

increase PS1 to 1V. If PS1 current reads less than

20mA, increase PS1 to 3.3V until VM1 reads 3.3V

±10mV. VM2 should read between 1.174V to 1.226V.

VM3 should read above 3V.

3. Connect an oscilloscope voltage probe as shown in

Figure3a, between VOUT1 SNSE and GND1 SNSE

turrets. Set channel to AC-coupled, voltage scale to

20mV, and time base to 10µs/div. Check VOUT1 ripple

voltage. Output voltage ripple can also be measured

with a low inductor connector on TP1, as shown in

Figure3b.

4. Increase the load by 1A intervals up to 6A and observe

the voltage output regulation, ripple voltage, SW be-

havior and the voltage on the SSTT1 turret. Calculate

Die temperature using the formula below:

TJ(°C) =

SSTT

4mV

– 273

(1)

5. If other operation modes are desired. Turn off PS1, set

LD1 to 0A and set JP1 to FC/SYNC or BURST posi-

tion. Turn on PS1, slowly increase LD1 and observe

the change in PS1 output current, SW behavior and

output ripple.

6. Optional: To change the frequency, remove R9. Install

the desired RT resistor in the R4 location. Size the

inductor, output capacitors and compensation com-

ponents to provide the desired inductor ripple and a

stable output. Refer to the LTC3312SA data sheet and

LTPowerCAD for more information on choosing the

required components.

7. Optional: To SYNC to a speciﬁc frequency, set JP1 to

FC/SYNC position. Connect a waveform generator to

MODE/SYNC turret. Please refer to LTC3312SA data

sheet for synchronization signal requirements.

8. To test the transient response with a base load, add the

desired resistor to produce a minimum load between

VOUT and RSNS1 turrets (RL1 shown on Figure2).

Note that the total load resistance will be RL1 plus

R11 (100mΩ). Adjust a signal generator with a 10ms

period, 10% duty cycle and an amplitude from 1V to

2V to start.

9. Measure the RSNS1 voltage to observe the current,

VRSNS1/100mΩ. Adjust the amplitude of the pulse to

providethedesiredtransient.Connectsignalgenerator

SG1 between SG_INPUT and GND turrets. Adjust the

rising and falling edge of the pulse to provide the de-

sired ramp rate. Refer to the following equations for

output current measurement:

IOUT =

RSNS1

100mΩ

(2)

10. When done, turn off SG1, PS1 and Load.

Test BUCK2 (VOUT2)

11. Followsimilar steps forBUCK1tests.Changethe setup

to LD2, VM4, VM5, SG2, RL2. VOUT2 should read

between 1.755V to 1.843V when powered.

12. When done, turn off all the supplies and loads. Discon-

nect all the cables.

DEMO MANUAL DC3091A

Rev. 0

Figure3a. Technique for Measuring Output Ripple and

Step Response

Figure3b. Technique for Measuring Output Ripple and Step

Response with a Low Inductance Connector (Not Supplied)

TEST SETUP

Figure2. Test Setup for DC3091A Demo Board

VM2SG1

VM1SG2

VM5

VM4

PS1

3.3V

10A LD2

LD1

VM3

DEMO MANUAL DC3091A

Rev. 0

FC MODE

Burst Mode OPERATION

PULSE SKIP MODE

LOAD

(A)

0.001

0.01

0.1

100

EFFICIENCY (%)

= 2MHz,

TDK TFM252012ALMAR22MTAA

dc3091a F05

249k

1µF

22µF

220nH

10nF

1µF

0.015µF

140k

100k

47µF

×2

249k

1µF

22µF

0.015µF

100k

330nH

22nF

107k

41.2k

47µF

×2

100k

IN1

IN2

EN1

SW1

LTC3312SA

OUT1

1.2V

MODE/SYNC

2.25V TO

5.5V

FB1

AGND

EN2

SSTT1

PGND

SSTT2

PGOOD1

SW2

OUT2

1.8V

FB2

PGOOD2

dc3091a F04

Figure4. LTC3312SA Dual 6A Buck Typical Application Schematic

Figure5. Output1 Efficiency vs Load

Efficiency, VIN = 3.3V, VOUT = 1.2V

All Modes

Figure6. Output2 Efficiency vs Load

Efficiency, VIN = 3.3V, VOUT = 1.8V

All Modes

TYPICAL PERFORMANCE CHARACTERISTICS

= 2MHz,

MURATA DFE252012F-R33M

LOAD

(A)

0.001

0.01

0.1

100

EFFICIENCY (%)

dc3091a F06

FC MODE

Burst Mode OPERATION

PULSE SKIP MODE

DEMO MANUAL DC3091A

Rev. 0

DC3091A DEMO BOARD

(WITH VOLTAGE APPLIED TO V

EMI INPUT)

3.3V INPUT TO 1.2V AND 1.8V OUTPUT AT 4.8A, f

= 2MHz

HORIZONTAL POLARIZATION

CLASS 5 PEAK LIMIT

MEASURED EMISSIONS

AMBIENT NOISE

FREQUENCY (MHz)

100

200

300

400

500

600

700

800

900

1000

–20

–10

AMPLITUDE (dBµV/m)

dc3091a F10

DC3091A DEMO BOARD

(WITH VOLTAGE APPLIED TO V

EMI INPUT)

3.3V INPUT TO 1.2V AND 1.8V OUTPUT AT 4.8A, f

= 2MHz

CLASS 5 PEAK LIMIT

MEASURED EMISSIONS

AMBIENT NOISE

FREQUENCY (MHz)

100

110

–20

–10

AMPLITUDE (dBµV/m)

dc3091a F09

Figure7. Output1 Load Step Response

Figure9. CISPR25 Conducted Emission Test with Class 5

Peak Limits (Voltage Method)

Load Transient Response, Forced

Continuous Mode

CISPR25 Conducted Emission Test with Class 5 Peak

Limits (Voltage Method) (Supply)

Figure8. Output2 Load Step Response

Figure10. CISPR25 Radiated Emission Test with Class 5

Peak Limits

Load Transient Response, Forced

Continuous Mode

Radiated EMI Performance (CISPR25 Radiated

Emissions Test with Class 5 Peak Limits)

TYPICAL PERFORMANCE CHARACTERISTICS

EMI TEST RESULTS

3.3V

TO 1.2V

OUT

, 2MHz

LOAD STEP: 0.1A TO 4.5A IN 1µs

10µs/DIV

OUT

50mV/DIV

LOAD

2.5A/DIV

2A/DIV

dc3091a F07

3.3V

TO 1.8V

OUT

, 2MHz

LOAD STEP: 0.1A TO 4.5A IN 1µs

10µs/DIV

OUT

50mV/DIV

LOAD

2.5A/DIV

2A/DIV

dc3091a F08

DEMO MANUAL DC3091A

Rev. 0

THEORY OF OPERATION

Introduction to the DC3091A

The DC3091A demonstration circuit features the

LTC3312SA, 5V, Dual 6A/Dual-Phase 12A step-down DC/

DC regulator. The LTC3312SA contains two monolithic,

constant frequency, current mode step-down DC/DC con-

verters. An oscillator, shared by two converters, with fre-

quency set by a resistor on the RT pin, turns on the inter-

nal top power switch at the beginning of each clock cycle.

The beginning of each clock cycle of the two converters

are 180-degree out of phase. Current in the inductor then

increases until the top switch comparator trips and turns

off the top power switch. The peak inductor current, at

which the top switch turns off, is controlled by the voltage

on the internal ITH node, which is the output of the error

amplifier. The internal ITH node is connected with internal

compensator to stabilize the control loop. The error ampli-

fier servos the ITH node by comparing the voltage on the

VFB pin with an internal 500mV reference. When the load

current increases, it causes a reduction in the feedback

voltage relative to the reference leading the error amplifier

to raise the ITH voltage until the average inductor current

matches the new load current. When the top switch turns

off, the synchronous bottom power switch turns on until

the next clock cycle begins. In pulse skip mode and Burst

Mode, the bottom switch also turns off when inductor cur-

rent falls to zero. If overload conditions result in excessive

current flowing through the bottom switch, the next clock

cycle will be delayed until the switch current returns to

a safe level. In Burst Mode, the error amplifier and most

part of the internal circuitry can be turned off until output

voltage trips an output low comparator, during extreme

light load condition, to improve light load efficiency.

If the ENx pin is low, the corresponding converter in

LTC3312SA is in shutdown and in a low quiescent cur-

rent state. When the ENx pin is above its threshold, the

corresponding switching converter will be enabled.

The MODE/SYNC pin synchronizes the switching fre-

quency to an external clock. It also sets the PWM mode.

The PWM modes of operation are Burst, Pulse Skip and

Forced Continuous. See the LTC3312SA data sheet for

more detailed information.

The maximum allowable operating frequency is influenced

by the minimum on time of the top switch, the ratio of

VOUT to VIN and the available inductor values. The maxi-

mum allowable operating frequency may be calculated in

the formula below.

SW(MAX)=

OUT

IN(MAX) • tON(MIN)

(3)

Select an operating switching frequency below fSW(MAX).

Typically, it is desired to obtain an inductor current of 30%

of the maximum LTC3312 operating load, 6A. Use the

formulas below to calculate the inductor value to obtain

a 30% (1.8A) inductor ripple for the operating frequency.

L≥VOUT

1.8A • f

• 1– VOUT

IN(MAX)

⎛

⎝

⎜⎞

⎠

⎟for VOUT

IN(MAX)

≤0.5

(4)

L≥

0.25 • V

IN(MAX)

1.8A • f

for VOUT

IN(MAX)

>0.5

(5)

The overall control loop of the converter can be tuned

by output capacitors and feedforward capacitors. The

LTC3312SA has been designed to operate at a high

bandwidth for fast transient response capabilities. This

reduces required output capacitance to meet the desired

transient voltage range. C6 along with R11, or C28 along

with R14, provides a phase lead which will improve the

phase margin.

Loop stability is generally measured using the Bode Plot

method of plotting loop gain in dB and phase shift in

degrees. The 0dB crossover frequency should be less

the 1/6 of the operating frequency to reduce the effects

of added phase shift of the modulator. The control loop

phase margin goal should be 45° or greater and a gain

margin goal of 8dB or greater.

DEMO MANUAL DC3091A

Rev. 0

PARTS LIST

ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER

Required Circuit Components

1 5 C1, C13-C16 CAP., 1µF, X7T, 6.3V, 20%, 0201 MURATA, GRM033D70J105ME01D

2 2 C2, C3 CAP., 22µF, X5R, 10V, 20%, 0603 MURATA, GRM188R61A226ME15D

3 4 C4, C5, C17, C18 CAP., 47µF, X6S, 6.3V, 20%, 0805 TAIYO YUDEN, JMK212BC6476MG-T

4 1 C6 CAP., 10pF, C0G/NP0, 50V, ±0.5pF, 0402 TDK, C1005C0G1H100D050BA

5 1 C19 CAP., 22pF, C0G, 50V, 10%, 0402 AVX, 04025A220KAT2A

6 2 C29, C35 CAP., 0.015µF, X7R, 16V, 10%, 0402 MURATA, GRM155R71C153KA01J

7 1 L1 IND., 220nH, 20%, 6.7A, 13mΩ TDK, TFM252012ALMAR22MTAA

8 1 L2 IND., 330nH, 20%, 19mΩ MURATA, DFE252012F-R33M=P2

9 1 R1 RES., 140k, 1%, 1/16W, 0402 NIC, NRC04F1403TRF

10 1 R2 RES., 100k, 1%, 1/16W, 0402 NIC, NRC04F1003TRF

11 1 R14 RES., 107k, 1%, 1/16W, 0402 NIC, NRC04F1073TRF

12 1 R15 RES., 41.2k, 1%, 1/16W, 0402 VISHAY, CRCW040241K2FKED

13 1 U1 IC, 5V, DUAL 6A/DUAL PHASE 12A STEP-DOWN

DC/DC REGULATOR, LQFN

ANALOG DEVICES, LTC3312SAAV#PBF

Additional Demo Board Circuit Components

1 2 C7, C8 CAP., 470µF, TANT, POSCAP, 6.3V, 20%, 7343, 18mΩ PANASONIC, 6TPE470MI

2 1 C9 CAP., 0.1µF, X7R, 25V, 10%, 0402 MURATA, GCM155R71E104KE02D

3 2 C10, C11 CAP., 10µF, X7S, 6.3V, 20%, 0603 TDK, C1608X7S0J106M080AC

4 2 C12, C24 CAP., 0.22µF, X7R, 6.3V, 20%, 0603 JOHANSON DIELECTRICS, 6R3X14W224MV4T

5 2 C22, C23 CAP., 1000pF, X7R, 50V, 20%, 0402, 3-TERM, X2Y

EMI FILTER

JOHANSON DIELECTRICS, 500X07W102MV4T

6 1 L3 IND., 100Ω AT 100MHz, FERRITE BEAD, 25%, 8A,

6mΩ, 1812

WURTH ELEKTRONIK, 74279226101

7 2 Q1, Q2 XSTR., MOSFET, N-CH, 40V, 15.9A, PPAK SO-8 VISHAY, SIR426DP-T1-GE3

8 2 R3, R12 RES., 20Ω, 1%, 1/16W, 0402 NIC, NRC04F20R0TRF

9 3 R5, R10, R18 RES., 10k, 5%, 1/10W, 0402 PANASONIC, ERJ2GEJ103X

10 2 R6, R16 RES., 1M, 1%, 1/16W, 0402 NIC, NRC04F1004TRF

11 2 R7, R17 RES., 249k, 1%, 1/16W, 0402 NIC, NRC04F2493TRF

12 2 R8, R13 RES., 100k, 5%, 1/16W, 0402 YAGEO, RC0402JR-07100KL

13 1 R9 RES., 0Ω, 1/16W, 0402 NIC, NRC04ZOTRF

14 2 R11, R19 RES., 0.1Ω, 1%, 2W, 2512, SENSE IRC, LRC-LR2512LF-01-R100-F

15 2 TP1, TP2 CONN., U.FL, RECEPT, ST SMD, 0Hz TO 6GHz 50Ω HIROSE ELECTRIC, U.FL-R-SMT-1(10)

16 2 TP1_PLUG, TP2_PLUG CONN U.FL PLUG STR 50Ω SMD HIROSE ELECTRIC, U.FL-PR-SMT2.5-1(10)

Hardware: For Demo Board Only

1 18 E1-E3, E5, E12, E14-E16, E19,

E21, E26-E29, E30, E32-E34

TEST POINT, TURRET, 0.064" MTG. HOLE, PCB

0.062" THK

MILL-MAX, 2308-2-00-80-00-00-07-0

2 9 E4, E7, E11, E13, E18, E20, E24,

E25, E31

TEST POINT, TURRET, 0.094" MTG. HOLE, PCB

0.062" THK

MILL-MAX, 2501-2-00-80-00-00-07-0

3 7 E6, E8-E10, E17, E22, E23 CONN., BANANA JACK, FEMALE, THT, NON-

INSULATED, SWAGE, 0.218"

KEYSTONE, 575-4

4 1 JP1 CONN., HDR, MALE, 1×4, 2mm, VERT, ST, THT WURTH ELEKTRONIK, 62000411121

5 2 JP2, JP3 CONN., HDR, MALE, 1×3, 2mm, VERT, ST, THT WURTH ELEKTRONIK, 62000311121

5 4 MP1-MP4 STANDOFF, NYLON, SNAP-ON, 0.50" WURTH ELEKTRONIK, 702935000

6 3 XJP1, XJP2, XJP3 CONN., SHUNT, FEMALE, 2 POS, 2mm WURTH ELEKTRONIK, 60800213421

DEMO MANUAL DC3091A

Rev. 0

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog

Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications

subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

SCHEMATIC DIAGRAM

REVISION HISTORY

ECO REV DESCRIPTION APPROVED DATE

-03 PRODUCTION WL 09-10-2021

1.2V

2.25V - 5.5V

VOUT1

MODE/SYNC

GND

EN1

PGOOD1

GND

MODE/SYNC

VIN

GND

EN1

VIN

GND

VOUT1

GND

VOUT1

SNSE

GND1

SNSE

VIN

SNSE

GND

SNSE

FC/SYNC

BURST

SKIP

PCA ADDITIONAL PARTS

NOTES: UNLESS OTHERWISE SPECIFIED

1. RESISTORS: OHMS, 0402, 1%, 1/16W

2. CAPACITORS: 0402

VIN EMI

2.25V - 5.5V

FSW=2MHz

GND

VIN MAX

OPTIONAL EMI FILTER

RSNS1

SG1

OPTIONAL TRANSIENT RESPONSE CIRCUIT

20V MAX

VOUT2

SNSE

1.8V

VOUT2

GND2

SNSE

GND

PGOOD2

EN2

20V MAX

SG2

RSNS2

SSTT1

SSTT2

VOUT1

GND

3.3V VIN, DUAL 6A, 2MHz SYNCHRONOUS STEP-DOWN

REGULATORS WITH 1.2V AND 1.8V OUTPUTS

VIN

DATE:

SHEET OF

TITLE: SCHEMATIC

APPROVALS

PCB DES.

APP ENG.

SIZE:

SCHEMATIC NO. AND REVISION:

CUSTOMER NOTICE

THIS CIRCUIT IS PROPRIETARY TO ANALOG DEVICES AND

SUPPLIED FOR USE WITH ANALOG DEVICES PARTS.

www.analog.com

SKU NO.

IC NO.

ANALOG DEVICES HAS MADE A BEST EFFORT TO DESIGN A

CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;

HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO

VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL

APPLICATION. COMPONENT SUBSTITUTION AND PRINTED

CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT

PERFORMANCE OR RELIABILITY. CONTACT ANALOG DEVICES

APPLICATIONS ENGINEERING FOR ASSISTANCE.

710-DC3091A_REV03

N/A

LTC3312SA

DC3091A

09-10-21DATE:

SHEET OF

TITLE: SCHEMATIC

APPROVALS

PCB DES.

APP ENG.

SIZE:

SCHEMATIC NO. AND REVISION:

CUSTOMER NOTICE

THIS CIRCUIT IS PROPRIETARY TO ANALOG DEVICES AND

SUPPLIED FOR USE WITH ANALOG DEVICES PARTS.

www.analog.com

SKU NO.

IC NO.

ANALOG DEVICES HAS MADE A BEST EFFORT TO DESIGN A

CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;

HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO

VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL

APPLICATION. COMPONENT SUBSTITUTION AND PRINTED

CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT

PERFORMANCE OR RELIABILITY. CONTACT ANALOG DEVICES

APPLICATIONS ENGINEERING FOR ASSISTANCE.

710-DC3091A_REV03

N/A

LTC3312SA

DC3091A

09-10-21DATE:

SHEET OF

TITLE: SCHEMATIC

APPROVALS

PCB DES.

APP ENG.

SIZE:

SCHEMATIC NO. AND REVISION:

CUSTOMER NOTICE

THIS CIRCUIT IS PROPRIETARY TO ANALOG DEVICES AND

SUPPLIED FOR USE WITH ANALOG DEVICES PARTS.

www.analog.com

SKU NO.

IC NO.

ANALOG DEVICES HAS MADE A BEST EFFORT TO DESIGN A

CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS;

HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO

VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL

APPLICATION. COMPONENT SUBSTITUTION AND PRINTED

CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT

PERFORMANCE OR RELIABILITY. CONTACT ANALOG DEVICES

APPLICATIONS ENGINEERING FOR ASSISTANCE.

710-DC3091A_REV03

N/A

LTC3312SA

DC3091A

09-10-21

TPB2

C18

47uF

0805

E13

C16

1uF

0201

R17

249k

MP1 STANDOFF,NYLON,SNAP-ON,0.50"

E16

220nH

TFM252012ALMAR22MTAA

C24

0.22uF

C13

1uF

0201

100k

R14

107k

E21

R12

MP3 STANDOFF,NYLON,SNAP-ON,0.50"

SIR426DP-T1-GE3

C14

1uF

0201

C19

22pF

MP2 STANDOFF,NYLON,SNAP-ON,0.50"

C12

0.22uF

140k

C20

0.015uF

TP2

PCB1 PCB, DC3091A REV03

SIR426DP-T1-GE3

1uF

0201

MP4 STANDOFF,NYLON,SNAP-ON,0.50"

E34

E11

47uF

0805

22uF

0603

E30

E19

E32

LB1 LABEL

100k

E10

470uF

6TPE470MI C9

0.1uF

E22

E29

E14

330nH

DFE252012F-R33M=P2

C17

47uF

0805

R18

10k

C10

10uF

0603

R15

41.2k E23

249k

R10

10k

C11

10uF

0603

47uF

0805

E18

E31

E20

10k

C21

0.015uF

E24

22uF

0603

LTC3312SAAV

PVIN2

SW1 5

FB1 2

MODE/SYNC 15

PGOOD1 4

PGOOD2 16

PVIN1

PGND

AGND

PVIN1

8SW1 6

PGND

PVIN2

SSTT1

SSTT2

EN1

EN2

SW2 13

SW2 14

FB2 17

AVIN 21

PGND

E17

E25

E28

JP2

TPA2

R13

100k

100 OHMS@100MHz

74279226101

E33

R16

R19

0.1

2512

R11

0.1

2512

10pF

E26

TPA1

C22

1000pF

E12

JP1

E27

E15

TP1

C23

1000pF

JP3

C15

1uF

0201

OPT

470uF

6TPE470MI

TPB1

VOUT1

VOUT2

VOUT2VOUT1

DEMO MANUAL DC3091A

Rev. 0

 ANALOG DEVICES, INC. 2022

03/22

www.analog.com

ESD Caution

ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection

circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

Legal Terms and Conditions

By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and

conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation

Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”)

and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to

Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and

agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted

is expressly made subject to the following additional limitations:Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board;and (ii) permit any Third

Party to access the Evaluation Board. As used herein, the term “Third Party”includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is

NOT sold to Customer;all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all

be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of

use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile

or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited

to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS

Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF

LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS”AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY

DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS

LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING

BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE

HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States

federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts

(excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits

to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Analog Devices Microcontrôleur