Ametek AMEVision 3050-OLV Guide de configuration
Model 3050-OLV
Moisture Analyzer
General Purpose
Plate Mounted Sample System
Manual Supplement
Process Instruments
455 Corporate Boulevard
Newark, DE 19702
PN 305514001 Rev. G
2 3050-OLV Plate Mounted Sample System
© 2000 AMETEK
is manual is a guide for the use of the 3050-OLV Moisture Analyzer. Data herein has been veried and validated and is be-
lieved adequate for the intended use of this instrument. If the instrument or procedures are used for purposes over and above
the capabilities specied herein, conrmation of their validity and suitability should be obtained; otherwise, AMETEK does not
guarantee results and assumes no obligation or liability. is publication is not a license to operate under, or a recommendation
to infringe upon, any process patents.
33050-OLV Plate Mounted Sample System
Installation
Unpacking and Inspection
Remove components from the packing case(s) carefully; check contents against packing list.
Inspect all components for obvious damage and broken/loose parts or fittings. Notify the car-
rier and AMETEK Service (1-800-537-6044) immediately if parts are missing or damage is found.
Sample System Space Requirements
Sample system mounted on a panel - approximately 21 x 8 x 21 cm plus clearance for analyzer
connections. Refer to Figure 3.
Power Requirements
The System is shipped according to the customer order and is fused and set for the voltage of
the required mains power. The power requirements are stated near the power entry for the
component and in the Specification Section of analyzer manual.
System Tubing
Recommended system tubing is 1/8 inch OD, 316 stainless steel meeting ASTM #632 specifica-
tions (AMETEK PN 571061017 or equivalent).
Dry Reference Gas
A dryer (AMETEK Dryer PN 305400901S or equivalent) is required to dry reference gas to less
than 0.025 ppmv.
Dryers must be periodically replaced. In normal use, the dryer (PN 305400901S) should dry a
50-ppm reference gas to specification for 1 year.
Sample pressure and temperature requirements
Pressure reduction is user supplied to ensure sample pressure to the analyzer remains within
the minimum and maximum range of 20 - 50 psig. The pressure reducer/regulator with gauge
should be installed near the sample tap in-between the tap and analyzer. Refer to figure 2.3 in
analyzer manual. For optimum performance, sample line should be heat traced to maintain a
constant sample temperature. Optimum sample gas input is 60°C.
4 3050-OLV Plate Mounted Sample System
Mechanical Installation
Locate the 3050-OLV system as close as possible to the sample source. The unit should be
protected from direct exposure to weather and sunlight, and located so that the ambient
temperature specifications will not be exceeded.
1. If not already installed, install a main process shut-off valve and pressure reducer
(recommended) at the sample tap. Refer to users manual figure 2.3.
2. Mount system in selected location and bolt in place. Refer to figure 3.
2. Connect the exhaust fitting to appropriate vent system.
3. Open the main process shut-off valve and purge sample line to an appropriate area
for at least five minutes. Close the main process shut-off valve. This will help prevent
contamination from entering the cell.
4. Connect the sample line to the sample inlet 1/8-inch compression fitting.
Electrical Connections
1. Access terminal block.
2. Connect the 4 to 20 mA analog output and alarm contacts from the terminal block
to user recording equipment as shown on wiring diagram figure 2.
3. Connect serial communication from analyzer to the PC being used for customer
parameter setup. Refer to figure 2.
RS-232 Out - Connect RS-232 cable to the back of the analyzer.
OR
RS-485 In - Connect RS-485 in cable to the terminal block. Refer to wiring diagram
figure 2.
RS-485 Out - Termination plug is installed at the factory. Remove the RS-485 ter-
mination plug from the RS-485 Out connector when communicating with multiple
analyzers except for the last analyzer in a chain.
The conduit housing must be removed for access to the RS-485 Out conector on the ana-
lyzer. Refer to figure 3.
4. Connect line power to analyzer.
NOTE
53050-OLV Plate Mounted Sample System
Dryer Valve
Micron Filter
3050
Back Press. Reg.
DRYER
Liquid Trap
CONTAMINANT TRAP
SAMPLE
INLET
BYPASS
EXHAUST SAMPLE
EXHAUST
Bypass Valve
Figure 1: Sample system flow diagram
6 3050-OLV Plate Mounted Sample System
Figure 2: Sample
system
73050-OLV Plate Mounted Sample System
Figure 3: 4-20mA Output
4-20 mA Output, Loop Powered (TB-3) See Note 6
3 4 5 6
3 4 5 6
4-20 mA Output, Self Powered (TB-3) See Note 7
R
Load
+ -
External 24V DC
Supply
+-
R
Load
+-
4-20 mA Output, Wiring
Notes
1.
Cable should be shielded with single twisted pair.
2. Cable shields should be connected to both the analyzer and the DCS. If this is not
possible, cable shields should be tied to the chassis at each 3050-OLV. If this is not
possible, tie the shield at the PC or DCS to chassis and remaining shield to the chassis
through a 0.1 mF @ 500V capacitor.
100 to 300 Ohm
100 Ohm
100 to 400 Ohm
3. e 3050 signal common is connected to earth ground. If the analog output is also
grounded, the analog output will no longer be electrically isolated. Contact AMETEK if
this situation occurs.
Ω4. Analyzer power must be removed when connecting or disconnecting the 4-20 mA signal.
5. e 4-20 mA loop circuit must have a load resistance of between 100 and 500 ohms or
malfunction may occur (Max 100 ohms when local 4-20 ma display is present). If a loop check is
performed, a 100 ohm resistor must be placed in series with the ammeter.
6. In Loop Powered mode, remove factory installed 100 Ω resistor at TB3-5 to TB3-6
and jumper at TB3-3 to TB3-4.
7. In Self Powered mode when the optional local 4-20 ma display is present and no remote device is in use,
the circuit must be completed with factory installed jumper from TB3-3 to TB3-4 and an additional
100 Ω resistor from TB3-5 to TB3-6.
8 3050-OLV Plate Mounted Sample System
Figure 3a: Plate mounted sample system
Front view
Side view
53.34
(21.00)
49.53
(19.25)
53.34
(21.00)
49.53
(19.25)
1.27
(.50)
O
20.02
(7.88)
cm
(inches)
93050-OLV Plate Mounted Sample System
Figure 4: Sample system
Liquid
Separator
(Optional)
Power Supply
7 Micron Filter
Dryer
Dryer Valve
3050-OLV Analyzer
Analyzer Power &
Signal Connections
Back Pressure
Reg. (Optional)
Terminal Block
(Incoming Power)
Contaminant Trap
(Optional)
The Plate mount sample system is for use in general purpose locations only. and must be
enclosed in a lockablespace not less than 24” x 24” x 12” so that access to the power supply,
terminal block, and wiring is prevented.
NOTE
10 3050-OLV Plate Mounted Sample System
Replacement Parts
Table 1 lists the replacement parts available for the Model 3050-OLV Moisture Analyzer. Please
contact the AMETEK Sales office (800-222-6789) for pricing and ordering information.
Table 1
Model 3050-OLV Sample System Replacement Parts
AMETEK
Part Description Part Number
Dryer* 305 400 901S
Contaminant Trap 305 007 901S
Contaminant Trap Cartridge 305 527 901S
Liquid Trap 305 008 901S
Liquid Trap Membrane FLT Replacement Kit 305 529 901S
Pressure Regulator, standard 305 170 901
Pressure Regulator, heated (115V) 259 891 001
Pressure Regulator, heated (240V) 259 891 002
Back Pressure Regulator 305 426 901S
Sample System 24 Volt DC Power Supply 230 539 001
2 Micron Filter 305448902S
Fuse (3.0A) 271 081 001
System Tubing, 1/8 inch OD, 316 SST 571 061 017
Heat Trace Replacement Kit 120 V 305 512 901
Heat Trace Replacement Kit 240 V 305 513 901
Autres manuels pour AMEVision 3050-OLV
2
Table des matières
Autres manuels Ametek Instrument de mesure
Ametek
Ametek Land Cyclops L Series Manuel utilisateur
Ametek
Ametek TRACE ANALYTICAL ta7000F Series Manuel utilisateur
Ametek
Ametek 5100 HD Manuel utilisateur
Ametek
Ametek Davenport PET Plus Manuel utilisateur
Ametek
Ametek Chandler Engineering 8340 Manuel utilisateur
Ametek
Ametek Reichert 13104190 Manuel utilisateur
Ametek
Ametek Mocon Dansensor MAP Mix 9001 ME Manuel utilisateur
Ametek
Ametek WDG-V Manuel utilisateur
Ametek
Ametek IPS-4-UV Manuel utilisateur
Ametek
Ametek Reichert AR5 Manuel utilisateur
Ametek
Ametek 5910 Manuel utilisateur
Ametek
Ametek BROOKFIELD JEROME 631-X Manuel utilisateur
Ametek
Ametek c Manuel utilisateur
Ametek
Ametek 3050-AM Manuel utilisateur
Ametek
Ametek AMEVision 3050 Series Manuel utilisateur
Ametek
Ametek DTI 1000 Manuel utilisateur
Ametek
Ametek JOFRA CTC-1200 A Manuel utilisateur
Ametek
Ametek BROOKFIELD CT3 Manuel utilisateur
Ametek
Ametek SPECTRO SPECTROCHECK Manuel utilisateur
Ametek
Ametek AMEVision 3050-OLV Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur