Ametek Mocon Dansensor MAP Mix 9001 ME Manuel utilisateur

P/N 250151-P

10/2021

User Manual

This blank page has been inserted to enable double sided

printing of the document!

Dansensor®MAP Mix 9001 ME EN User Manual

P/N 250151-P

10/2021

User Manual

Published by: MOCON Europe A/S

Rønnedevej 18

4100 Ringsted, Denmark

Tel +45 57 66 00 88

info.dk.mocon@ametek.com

www.dansensor.com

2 User Manual EN Dansensor®MAP Mix 9001 ME

P/N 250151-P

10/2021

Dansensor®MAP Mix 9001 ME EN User Manual 3

P/N 250151-P

10/2021

Table of Contents

1. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2. Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3. Equipment set up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Gas connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Mounting of filters and gas connection fittings . . . . . . . . . . . . . . . . 11

Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4. Control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Flow control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5. Spare parts and options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Recommended spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Consumable parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

6. Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

4 User Manual EN Dansensor®MAP Mix 9001 ME

P/N 250151-P

10/2021

Dansensor®MAP Mix 9001 ME EN User Manual 5

P/N 250151-P

10/2021

1. Introduction

Dansensor® MAP Mix 9001 ME is MOCON Europe A/S´ equipment for gas mixing and

monitoring of gas and pressure.

Dansensor® MAP Mix 9001 ME is a proportional gas mixer especially designed for packaging

machines and other industrial applications, where the gases N2, CO2and O2are used in either

2-gas or 3-gas combinations.

The mixing principle of Dansensor® MAP Mix 9001 ME is very stable and can be used for all

types of packaging machines, both flow packaging machines, vacuum packaging machines

and other industrial processes.

Dansensor® MAP Mix 9001 ME is user-friendly with very high precision, also under

conditions which usually cause problems for most other types of gas mixers.

Fig. 1. Dansensor® MAP Mix 9001 ME

6 User Manual EN Dansensor®MAP Mix 9001 ME

P/N 250151-P

10/2021

Dansensor®MAP Mix 9001 ME EN User Manual 7

P/N 250151-P

10/2021

2. Safety instructions

Read and understand this manual for your own safety and for the quality of the work you

perform with this equipment.

The following terms are used in this manual:

DANGER! Describes a condition which MAY lead to mortal danger or serious injury.

WARNING! Describes a condition which MAY lead to serious injury or destruction of

the equipment in question.

ATTENTION! Describes a condition which MAY lead to incorrect operation of the

equipment, resulting in incorrect measuring results.

Please observe the following instructions carefully:

DANGER! Opening the apparatus may involve the risk of mortal danger or serious

injury. It may expose live high-voltage wires.

Dansensor® MAP Mix 9001 ME should be opened by authorised personnel only.

At the back of the mixer there is an indication of where the gases must be

connected to the individual inlets. O2(oxygen) must NEVER be connected to other

inlets than the one marked for O2(oxygen).

Do NOT use this equipment for air supply for human beings.

When using the mains supply Dansensor® MAP Mix 9001 ME must be grounded.

WARNING! Always use fittings and hoses which apply to the gasses used and to the

intended use of the mixer.

Always use the correct tools and hold against on the gas in- and outlet fittings

when connecting/disconnecting the gas connection fittings (see "Gas connection"

on page 9 for details).

In order to avoid damage to the internal parts of the gas mixer, "GAS IN" must

always be connected and supplied last.

When moving or transporting Dansensor® MAP Mix 9001 ME care must be taken not

to bump the equipment.

Dansensor® MAP Mix 9001 ME must be transported in the original shipping

container if warranty repairs are needed. Failure to do so invalidates the warranty.

On buffer-tank versions make sure that the gas outlet is NEVER blocked or restricted

in front of the buffer tank (see "Gas connection" on page 9 for details).

NEVER expose the device to more than 10 bars, as this may damage internal

components in the device.

ATTENTION! When using the 3-gas mixer as a 2-gas mixer, you must ALWAYS

connect N2or CO2to the inlet which "is not to be used".

See "3-gas mixer used as 2-gas mixer" on page 17.

8 User Manual EN Dansensor®MAP Mix 9001 ME

P/N 250151-P

10/2021

Table des matières

Autres manuels Ametek Instrument de mesure

Ametek

Ametek Western Research IPS-4 Manuel utilisateur

Ametek

Ametek DM330 Series Manuel utilisateur

Ametek

Ametek Thermox CEM O2/TM Manuel utilisateur

Ametek

Ametek Z-tron III Manuel utilisateur

Ametek

Ametek Drexelbrook Universal IV CM Manuel utilisateur

Ametek

Ametek 241CE II Manuel

Ametek

Ametek Thermox WDG-V UOP Manuel utilisateur

Ametek

Ametek JOFRA DTI050 A Manuel utilisateur

Ametek

Ametek VersaSTAT LC Series Manuel utilisateur

Ametek

Ametek mAcal Manuel utilisateur

Ametek

Ametek Brookfield JEROME 651 Manuel utilisateur

Ametek

Ametek CHANDLER ENGINEERING 1200 Manuel utilisateur

Ametek

Ametek 502-3000 Series Manuel utilisateur

Ametek

Ametek si 5000 Manuel utilisateur

Ametek

Ametek Reichert 13104190 Manuel utilisateur

Ametek

Ametek Land SDS Manuel utilisateur

Ametek

Ametek c Manuel utilisateur

Ametek

Ametek Reichert 7CR Manuel utilisateur

Ametek

Ametek JOFRA RTC-156/157 B/C Manuel utilisateur

Ametek

Ametek 5830 Manuel utilisateur

Ametek

Ametek Tono-Pen XL Manuel utilisateur

Ametek

Ametek 7550 Manuel utilisateur

Ametek

Ametek Chandler Engineering 4207D Manuel utilisateur

Ametek

Ametek Thermox CEM/O2 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur