Ametek TELGUARD TG-PEM Manuel utilisateur

Quick Install Guide

TG-PEM Wiring Diagram

(zone connections not shown)

•The connection from

Telguard Power on the

TG-PEM to the DC

connection on the TG-7

or TG-7FS should be the

ONLY power supply

connection. The AC

power and battery

connectors must NOT

be used. LED8 (AC

Power) should not be

lit.

•Supervised zones utilize

2.2kΩEOL resistors (not

provided).

STEP-BY-STEP:

1. Register the TG-7 or TG-7FS

Use the dealer portal at www.telguard.com.

2. Pre-configure the TG-PEM prior to installation

Use the Power Expansion Module tab for the device registered.

3. Mount the TG-7 or TG-7FS

Complete all steps of the physical installation as outlined in the

TG-7 series manual. Do not activate yet.

4. Mount the TG-PEM

Tip: To ease mounting of TG-PEM board, pre-thread the metal bracket

using the provided mounting screws (marked in red in diagram)

•Remove top left mounting screw that holds the TG-7

series board (indicated by arrow).

•Orient bracket as shown in diagram.

•Insert bracket at an angle so that top mounting point

slides under board as depicted, and angled tab

threads through the enclosure bump out.

•Replace screw to securely mount bracket and board.

```

TG-7FS

LTE

Pre-thread using screws

LED1

LED2

LED3

LED4

LED5

LED6

LED7

LED8

DC STC2 STC1 TRIP BATT AC

Installing the TG-PEM inside the TG-7 or TG-7FS is simple, but watching our installation

video will get you going in no time and insure your installation is quick and easy.

Scan the QR code or visit telguard.com/pem for the installation video and other useful resources

including the full Installation Manual.

TG-7FS

LTE

LED1

LED2

LED3

LED4

LED5

LED6

LED7

LED8

Alarm Panel

Burglary Systems: STC1 needs to

be connected to a 24-hour panel

input zone to indicate alarm

conditions from TG-PEM. STC2

could be used to indicate TG-7

trouble conditions. Do Not Use these power

connectors when using TG-PEM.

Power from TG-PEM

TG-PEM

Panel Power (DC)

DC STC2 STC1 TRIP BATT AC

Fire Systems: STC1

needs to be connected

to a panel input zone

to indicate all trouble

conditions.

Use the three provided mounting screws to secure the TG-PEM

board onto the bracket.

5. Connect the TG-PEM to TG-7 or TG-7FS

•Make sure there are no AC or DC power sources

connected to the TG-7 or TG-7FS. Connect power and

ground from the TG-PEM terminal labeled “TELGUARD

POWER” to the terminal block on the TG-7 or TG-7FS

labeled DC and GND. Do not overtighten.

•Connect ribbon cable (provided) from the connector on

TG-PEM labeled “TO HOST” to the 3x2 6-pin header on

the TG-7 series board as shown. The dark color edge of

the ribbon cable should be oriented away from the

antenna of the TG-7 or TG-7FS.

6. Power Up and Configure

•Connect power and ground from the panel

auxiliary output to the terminal labeled “PANEL

POWER” on the TG-PEM to provide power to the

TG-PEM and TG-7 or TG-7FS.

•Complete the activation of the TG-7 or TG-7FS as

outlined in the TG-7 series manual.

•If the TG-PEM was preconfigured, it should now

be ready; otherwise, visit www.telguard.com to

configure the TG-PEM.

•When the TG-PEM is configured and ready, LED

D2 will be either solid amber (in power supply

only mode) or solid green (in power supply and

zone extender mode).

7. Connect Zone Inputs (if using)

•Temporarily disconnect the power while you

connect any monitoring sensors to the zone

inputs.

•For supervised zones, use a standard 2.2kΩEOL

resistor (not included).

•Reconnect power, allow the TG-7 or TG-7FS to

initialize, and check for proper operation.

Optional: Second TG-PEM Installation

See full Installation Manual for mounting and wiring

instructions.

REFERENCE:

LED

STATUS

DETAILS

Off

Green

Ready, no

activity

TG-PEM is ready

Off

Shut down

Power to TG-PEM is below

minimum

Any

Amber

flash

Communicator

activating

TG is being activated

Red

Green

Reportable

event

At least one enabled input is

tripped or event(s) captured

and waiting to be reported

Red

flash

Green

Event

reporting

Event(s) reporting or waiting

for response

Off

Red

flash

Bootloader

error

Device failure, contact

Technical Support

Off

Amber

Power supply

only or

Not ready

Power supply mode,

TG-PEM waiting for

configuration, or

Communicator not enabled

TO HOST TO TG-PEM D1 D2

Reset TELGUARD

POWER

PASS THRU

PANEL

POWER

DC GND

ZONE INPUTS

1 C 2 3 C 4 5 C 6 7 C 8

GND DC GND DC

```

TG-7FS

LTE

3x2 6-pin header Dark edge on right

LED1

LED2

LED3

LED4

LED5

LED6

LED7

LED8

DC STC2 STC1 TRIP BATT AC

56051801 –Rev A

Note: At power-up, both LEDs will be on for 3 seconds then off for 3 seconds.

Autres manuels Ametek Unité de contrôle

Ametek

Ametek Z-tron IV Manuel utilisateur

Ametek

Ametek Crystal Pressure APM CPF Series Manuel utilisateur

Ametek

Ametek GEMCO 1746R Series Instructions de montage

Ametek

Ametek PMC BOOSTER Series Manuel utilisateur

Ametek

Ametek UPLC-II Guide de l'utilisateur

Ametek

Ametek Thermox 2000 ATEX Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur