Amber connect ACT200 Manuel utilisateur

1. Characteristic

MODULE

Name

ACT200

Technology

GSM/GPRS/GNSS/BLUETOOT

GNSS

GPS, GLONASS, GALILEO, BEIDOU, SBAS, QZSS, DGPS,

AGPS

Receiver

33 channel

Tracking sensitivity

-165 dBM

Accuracy

< 3 m

Hot start

< 1 s

Warm start

< 25 s

Cold start

< 35 s

Cellular

Technology

GSM

2G bands

Quad-band 850 / 900 / 1800 / 1900 MHz

Data transfer

GPRS Multi-Slot Class 12 (up to 240 kbps), GPRS Mobile

Station Class B

Data support

SMS (text/data)

POWER

Input voltage range

10-30 V DC with overvoltage protection

Back-up battery

170 mAh Li-Ion battery 3.7 V (0.63 Wh)

Internal fuse

3 A, 125 V

Power consumption

At 12V < 6 mA (Ultra Deep Sleep)

At 12V < 8 mA (Deep Sleep)

At 12V < 11 mA (Online Sleep)

At 12V < 20 mA (GPS Sleep)

At 12V < 35 mA (nominal with no load)

At 12V < 1.5 A Max. (with full Load/Peak)

BLUETOOTH

Specification

4.0 + LE

Supported peripherals

Temperature and Humidity sensor, Headset, OBDII dongle,

Inateck Barcode Scanner, Universal BLE sensors support

INTERFACE

Digital Inputs

Digital Outputs

Analog Inputs

CAN Adapter inputs

1-Wire

GNSS antenna

Internal High Gain

GSM antenna

Internal High Gain

USB

2.0 Micro-USB

LED indication

2 status LED lights

Memory

128MB internal flash memory

PHYSICAL SPECIFICATION

Dimensions

65 x 56,6 x 20,6 mm (L x W x H)

Weight

55 g

FEATURES

Sensors

Accelerometer

Scenarios

Green Driving, Over Speeding detection, Jamming detection, GNSS

Fuel Counter, DOUT Control Via Call, Excessive Idling detection,

Immobilizer, iButton Read Notification, Unplug detection, Towing

detection, Crash detection, Auto Geofence, Manual Geo fence, Trip

Sleep modes

GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra Deep Sleep

SMS

Configuration, Events, DOUT control, Debug

GPRS commands

Configuration, DOUT control, Debug

Time Synchronization

GPS, NITZ, NTP

Fuel monitoring

LLS (Analog), LV-CAN200, ALL-CAN300, OBDII dongle, CAN-

CONTROL

Ignition detection

Digital Input 1, Accelerometer, External Power Voltage, Engine RPM

(CAN Adapters, OBDII dongle)

OPERATING ENVIRONMENT

Operating temperature

(without battery)

-40 °C to +85 °C

Storage temperature

(without

battery)

-40 °C to +85 °C

Operating humidity

5% to 95% non-condensing

Ingress Protection Rating

IP41

Battery charge temperature

0 °C to +45 °C

Battery discharge

temperature

-20 °C to +60 °C

Battery storage temperature

-20 °C to +45 °C for 1 month

-20 °C to +35 °C for 6 months

Bluetooth fuel sensor

Analog fuel sensor

RFID reader Wired temperature sensor

ACCESSORIES

Bluetooth and analog fuel sensor

RFID reader

Temperature sensor

2. Electrical characteristics

CHARACTERISTIC DESCRIPTION

VALUE

MIN.

TYP.

MAX.

UNIT

SUPPLY VOLTAGE

Supply Voltage (Recommended Operating

Conditions)

+10

+30

DIGITAL OUTPUT (OPEN DRAINGRADE)

Drain current (Digital Output OFF)

120

µA

Drain current (Digital Output ON,

Recommended Operating Conditions)

0.1

0.5

Static Drain-Source resistance (Digital Output

ON)

400

600

mΩ

DIGITAL INPUT

Input resistance (DIN1)

kΩ

Input resistance (DIN2)

51.7

kΩ

Input resistance (DIN3)

150

kΩ

Input voltage (Recommended Operating

Conditions)

Supply

voltage

Input Voltage threshold (DIN1)

7.5

Input Voltage threshold (DIN2)

2.5

Input Voltage threshold (DIN3)

2.5

ANALOG INPUT

Input voltage (Recommended Operating

Conditions), Range 1

+10

Input resistance, Range 1

38.45

kΩ

Measurement error on 12V, Range 1

0.9

Additional error on 12 V, Range 1

108

Measurement error on 30 V, Range 1

0.33

Additional error on 30 V, Range 1

Input Voltage (Recommended Operating

Conditions), Range 2

+30

Input resistance, Range 2

150

kΩ

Measurement error on 12 V, Range 2

0.9

Additional error on 12 V, Range 2

108

Measurement error on 30 V, Range 2

0.33

Additional error on 30 V, Range 2

OUTPUT SUPPLY VOLTAGE 1-WIRE

Supply voltage

+4.5

+4.7

Output inner resistance

Output current (Uout > 3.0 V)

Short circuit current (Uout = 0)

3. Pinout

NUMBER

PIN NAME

DESCRIPTION

VCC (10-30) V DC (+)

Power supply (+10-30 V DC).

AIN 1

Analog input, channel 1. Input range:

0-30 V DC.

AIN 2 / DIN 3

Analog input, channel 2. Input range: 0-30 V DC /

Digital input, channel 3.

DIN 2

Digital input, channel 2.

DIN 1

Digital input, channel 1.

INPUT 6

TX EXT (LVCAN –TX).

GND (-)

Ground pin. (10-30) V DC (―)

DOUT 1

Digital output, channel 1. Open collector output.

Max. 0,5 A DC

DOUT 2

Digital output, channel 2. Open collector output.

Max. 0,5 A DC

1WIRE POWER

+3,8 V output for 1–Wire devices.

1WIRE DATA

Data for 1–Wire devices.

INPUT 5

RX EXT (LVCAN - RX).

Accessories Connection Possibilities

4 IN ports/pin

o2 Digital

o1 Analog

o1 Digital or Analog

2 OUT ports/pins

o2 Digital (for future use)

1 One-wire connection

Installation team must follow the below Accessory connection for efficient working. If

installation has to be done with different patterns then please contact your immediate tech

support for the possibilities. You can configure these accessories settings in our amber

connect fleet management platform.

Fleet Portal > Settings > Vehicle > Safety > Device Input Configuration

[This setting available Only to specific device models that supports the accessories]

Warning: These settings should exactly match with the actual accessories connected to

the device ports during the installation. If you make any changes on this will result in data

reception from accessories to the device. So Kindly make sure you are changing this with

proper understanding of which accessory connected to which wire during the installation.

Wiring Scheme

4. Mounting Recommendations

1) Connecting wires

a) Wires should be connected while the module is not plugged in.

b) Wires should be fastened to stable wires or other non-moving parts. Any heat

emitting and/or moving objects should be kept away from the wires.

c) There should be no exposed wires. If factory isolation was removed while

connecting the wires, the isolation material should be applied.

d) If the wires are placed in the exterior or in places where they can be damaged or

exposed to heat, humidity, dirt, etc., additional isolation should be applied and the

wires should not be loose.

e) Wires cannot be connected to the board computers or control units.

2) Connecting power source

a) Be sure that after the car computer goes to sleep mode, power might be still

available on the power wires. Depending on the car model, this may happen in 5

to 30 minutes period.

b) When the module is connected, measure the voltage again to make sure it did not

decrease.

c) It is recommended to connect to the main power cable in the fuse box.

d) 3 A, 125 V external fuse shall be used.

3) Connecting ignition wire

a) Be sure to check if it is a real ignition wire i. e. power does not disappear after

starting the engine.

b) Check if this is not an ACC wire (when key is in the first position, most of the

vehicle electronics are available).

c) Check if power is still available when you turn off any of vehicles devices.

d) Ignition is connected to the ignition relay output. As alternative, any other relay,

which has power output when ignition is on, may be chosen.

4) Connecting ground wire

a) Ground wire is connected to the vehicle frame or metal parts that are fixed to the

frame.

b) If the wire is fixed with the bolt, the loop must be connected to the end of the

wire.

c) For better contact scrub paint from the spot where loop is going to be connected.

5. LED Indications

BEHAVIOUR

MEANING

Permanently switched on

GNSS signal is not received

Blinking every second

Normal mode, GNSS is working

Off

GNSS is turned off because: Device is not working or

Device is in Sleep mode

Blinking fast constantly

Device firmware is being flashed

BEHAVIOUR

MEANING

Blinking every second

Normal mode

Blinking every two seconds

Sleep mode

Blinking fast for a short time

Modem activity

Off

Device is not working or Device is in Boot mode

6. Safety information

This message contains information on how to operate safely. By following these

requirements and recommendations, you will avoid dangerous situations. You must read

these instructions carefully and follow them strictly before operating the device!

The device uses SELV limited power source. The nominal voltage is+12 V DC. The

allowed voltage range is +10…+30 V DC.

To avoid mechanical damage, it is advised to transport the device in an impact-proof

package. Before usage, the device should be placed so that its LED indicators are

visible. They show the status of device operation.

When connecting the 2x6 connector wires to the vehicle, the appropriate jumpers of the

vehicle power supply should be disconnected.



Before unmounting the device from the vehicle, the 2x6 connector must be

disconnected. The device is designed to be mounted in a zone of limited access, which

is inaccessible to the operator. All related devices must meet the requirements of EN

62368-1 standard. The device is not designed as a navigational device for boats.

Do not disassemble the device. If the device is damaged, the power supply cables are not

isolated or the isolation is damaged, DO NOT touch the device before unplugging the power

supply.

All wireless data transferring devices produce interference that may affect other devices

which are placed nearby.

The device must be connected only by qualified personnel.

The device must be firmly fastened in a predefined location.

The programming must be performed using a PC with autonomic power supply.



7. Certification and Approvals

EAC

REACH

Declaration of IMEI assignment

CE / RED

E-Mark

RoHS

Declaration of device operation temperature

This sign on the package means that it is necessary to read the User Manual before your start

using the device.

This sign on the package means that all used electronic and electric equipment should not be

mixed with general household waste.

Hereby, we declare under our sole responsibility that the above described product is in

conformity with the relevant Community harmonization: European Directive 2014/53/EU

(RED).



Installation and/or handling during a lightning storm is prohibited.

The device is susceptible to water and humidity.

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries

according to the instructions.

Battery should not be disposed of with general household waste. Bring damaged or worn-out

batteries to your local recycling center or dispose them to battery recycle bin found in stores.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels amber connect Terminal tactile

amber connect

amber connect Covert T300 Manuel utilisateur

amber connect

amber connect Amber Govern T400-la Manuel utilisateur

amber connect

amber connect Amber Covert T200 Manuel utilisateur

amber connect

amber connect Insight T210 Manuel utilisateur

amber connect

amber connect ACT400-m Manuel utilisateur

amber connect

amber connect Amber Vision C400 Manuel utilisateur

amber connect

amber connect Covert C411 Manuel utilisateur

amber connect

amber connect ACC410-E/LA Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manuel utilisateur

Ingenico

Ingenico AXIUM EX4000 Manuel utilisateur

Heisei Electronics

Heisei Electronics Q-POS 815 Manuel utilisateur

Amano

Amano MTX-15 Manuel utilisateur

FLOWBIRD

FLOWBIRD CWT Compact Touch Manuel utilisateur

Demco

Demco SP7 Manuel utilisateur

Lathem

Lathem PC600 Series Manuel utilisateur

Partner

Partner MF-2352 Manuel utilisateur

NCR

NCR RealPOS 7460-2 Manuel

Simrad

Simrad MS50 Instructions de montage

Unitech

Unitech MR350 MKII Guide de démarrage rapide

Jungheinrich

Jungheinrich WMT 210 Manuel utilisateur

Motorola

Motorola MTP850 Manuel utilisateur

YASKAWA

YASKAWA 62H-MDC0 Manuel utilisateur

MVG industries

MVG industries NeptuLink Manuel utilisateur

Price Industries Limited

Price Industries Limited FDC Manuel d'instructions

Honeywell

Honeywell TemaKey Manuel utilisateur

EBN

EBN BPC65-B-A16G Manuel utilisateur

amber connect ACT200 Manuel utilisateur

Manuels Terminal tactile populaires d'autres marques