Amano MTX-30P PUSH Instructions d'utilisation d'origine
MTX-30P PUSH INSTALLATION & OPERATION GUIDE
Thank You….
For purchasing another fine product from Amano Cincinnati, Inc.
Proprietary Notice
This document contains proprietary information and such information may not be reproduced in
whole or part without the written permission from Amano Cincinnati, Inc. 140 Harrison Ave.,
Roseland, New Jersey 07068.
Amano Cincinnati, Inc. reserves the right to make equipment changes and improvements,
which may not be reflected in this document. Portions of this document may have been
updated to include the latest hardware or firmware version, if applicable.
To ensure safe use of this terminal, be sure to thoroughly read this manual in its entirety before
any attempt is made to operate the equipment.After you have finished reading this manual, be
sure to store it in a safe place for further reference.
For more information about Amano’s complete line of products, visit our web site at:
www.amano.com
For on line help please visit our Knowledge base link at:
http://tkb.amano.com/phpkb/
Note:This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
MTX-30P Push Installation & Operation Guide
CONTENTS
MTX-30P PUSH INTRODUCTION………………………………………………5
What’s In the Box
BASIC INSTALLATION FOR TIME GUARDIAN MTX-30P PUSH…….……6 - 9
Wall Mounting
Installation
Understanding the MTX-30P Push Front Panel
STARTUP……………………………………………………………….…...........10
MTX-30P Push Startup Screen (Power On)
OPERATION………………………………………………………………………11-12
Daily MTX-30P Push Use
Punching with a Proximity Card (Prox.)
Punching with a Password (Pwd)
View Previous Punch at the Terminal (F3)
ENROLLING USERS…………………………………………………………….12
USER MANAGEMENT…………………………………………………………..13 -14
How to Enroll a New User
All Users
Display Style
USER ROLE……………………………………………………………………....15
COMMUNICATION……………………………………………………………….16
Ethernet
Wireless Network
MTX-30P Push Installation & Operation Guide
PERSONALIZE……………………………………………………………………17
Voice
DATA MANAGEMENT …………………………………………………............18 -19
Delete Data
Backup Data
Restore Data
MORE OPTIONS………………………………………………………..……......20
AUTOTEST…………………………………………………………………..…....21 -23
Test All
Test LCD
Test Voice
Test Keyboard
Test Clock RTC
Test Relay
SYSTEM INFORMATION…………………………………………………….….24 -25
Device Capacity
Device Info
Firmware Info
SPECIFICATIONS……………………………………………………………......26
MTX-30P Push Introduction
The MTX-30P Push is a sophisticated data collection terminal for use directly with Amano Time
Guardian to provide a complete PC or cloud based time and attendance solution for small
business.
The MTX-30P Push terminal with Amano Time Guardian provides a system that automatically
calculates and accumulates hours worked based on the company's payroll policies. This
system separates the hours worked into regular and overtime pay categories and displays
them at the terminal (if enabled).
Your MTX-30P Push terminal package should include the following:
•Proximity Card Data Collection Terminal
•100-240 V AC Power Adapter
•6 foot Cat 5 cable
•Mounting Bracket
•Plate and hardware
•One Prox ID card
What’s In the Box
MTX-30P Push Installation & Operation Guide Page 5
MTX-30P Push Installation & Operation Guide Page 6
Wall Mounting
Warning! Before selecting a mounting location for your MTX-30P Push Terminal, you
must consider the following:
The mounting surface and hardware must be able to support the unit’s weight, 1.35
lbs. (0.61kg).
The area must be within the specified operating temperature & humidity range (see
Specifications on page 27).
The MTX-30P Push proximity card terminal should be mounted in an
environment that avoids the following conditions:
X Heat Source –Direct Sunlight and Humidity
X Rain Water
X Strong Vibration and Shock
X Dust, Corrosive Gas, Steam and Salt Damage
Close proximity to a wall outlet (6 ft.)
If using Ethernet, close proximity to an Ethernet connection (6 ft.) or if connecting via
WiFi check the location for a good signal.
Amano recommends the following wall mounting procedure:
1. Set the MTX-30P Push terminal face up on a flat surface to avoid scratches on display.
2. Using the mounting bracket as a guide, mark the location of the upper and lower
mounting holes on the wall. It is recommended to mount the terminal 49.2” from the
floor to the bottom of the bracket. *Adjust for staff height as necessary.
Note: Pay attention to the orientation. The back plate should only be mounted one-way as it is
keyed to fit into the back of the proximity card reader.
Mounting Bracket
Basic Installation for Time Guardian MTX-30P Push
Back of Terminal
TOP
BOTTOM
MTX-30P Push Installation & Operation Guide Page 7
3. Install anchors at the marks and attach the mounting bracket to the wall.
4. Feed power and communication wires through the knockout in the bottom of the
mounting bracket.
5. Install the four screws attaching the metal back plate to the mounting bracket. Make sure
the two metal tabs are on top.
6. Plug in power connector and Ethernet cable (if using Ethernet) into the terminal. Also
connect signal wiring if applicable.
7. Slide the terminal onto the two tabs located at the top of the back plate. Secure
the reader to the back plate by inserting and tightening the screw located at the
bottom of the unit.
Your terminal is now mounted to the wall and ready to connect the power supply to the
outlet.
MTX-30P Push Installation & Operation Guide Page 8
The front panel of the MTX-30P Push terminal contains the following controls:
•LED Indicator: During normal standby operation (power on), the Green LED will flash
once per second. When a user successfully verifies the Green LED will stay solid for
three seconds. If a user fails to verify, the Red LED will stay on for three seconds.
Note: If the proximity card reader does not follow the standard LED operational parameters,
please consult support.
•Speaker: Provides audible voice verification of operations, i.e., "Thank you", "Incorrect
Password", "Access Denied", "Invalid Id", "Please try again", etc.
•TFT Display Screen: Displays time, date, day, and operational information.
•Proximity Card Senor: Proximity card must be presented approximately 1 inch in front
of the reader to punch.
•Keypad: Used to input User ID, password, and perform menu operations.
•USB Port: Insert USB to download software, copy over passwords, etc.
•Reset Button: Clear all current settings and go back to all factory default settings.
Front View Side View
USB Port
Reset Button
TFT Display Screen
LED Indicator
Keypad Speaker
Understanding the MTX-30P Push Terminal Front Panel
Front/Side Panel Features
Proximity Card
Sensor
MTX-30P Push Installation & Operation Guide Page 9
M/┘–Menu, OK
Power ON/OFF & space back.
Modify current item value.
- to scroll down or up for menu operations.
F3 –View Previous Punch
ESC –to perform exit, cancel, ignore when using the Menus.
Keypad Functionality
Power On/Off
Left Arrow Right Arrow
Menu and OK
Up & Down
Arrows
Prev. Punch
Numeric Keypad
Escape
MTX-30P Push Installation & Operation Guide Page 10
Startup
MTX-30P Push Startup AMANO Screen (Power On)
Once the terminal is wall mounted and the communication connections have been made,
connect the terminal to AC power and proceed on to setup and enroll users.
To start-up, perform the following: Ensure theAC Power Adapter is connected to the MTX-
30P Push terminal and plugged into an outlet. The MTX-30P Push terminal will display the
splash screen, perform a diagnostic check, and then display the Welcome screen.
Note: The time and date can be set with the terminal keypad, or downloaded to the terminal from the
host PC or cloud utilizing Time Guardian software. The information such as date, time, daylight saving
time (DST), proximity card templates, and hours worked sent from Time Guardian software will have
precedence over existing similar information. That is to say Time Guardian software will act as the
master/source.
Upon power up, the Green LED indicator will blink once every second to signify the terminal
is operating properly.
All normal time and attendance functions (validation for punch in/out) must be performed from
the Welcome screen.
Press the power On/Off button to shut down the MTX-30P Push proximity card terminal
and display "halting system….Shutdown 2 secs, 1sec". The MTX-30P Push terminal will
retain all templates and transactions while the power is off.
Autres manuels pour MTX-30P PUSH
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Amano Terminal tactile
Amano
Amano AFR-200 Instructions d'utilisation d'origine
Amano
Amano OPUS-4000 Series Manuel utilisateur
Amano
Amano OPUS-7000 Series Manuel utilisateur
Amano
Amano OPU Series Manuel utilisateur
Amano
Amano AFR-200 Manuel utilisateur
Amano
Amano MTX-30 Manuel utilisateur
Amano
Amano OPUS-7000 Series Manuel utilisateur
Amano
Amano FPT-40 Manuel utilisateur
Amano
Amano Time Guardian FRT-40 Manuel utilisateur
Amano
Amano MDR900-5-0-AC Series Manuel utilisateur
Manuels Terminal tactile populaires d'autres marques
Wincor Nixdorf
Wincor Nixdorf iPOS plus Advanced Manuel utilisateur
Ingenico
Ingenico AXIUM EX4000 Manuel utilisateur
Heisei Electronics
Heisei Electronics Q-POS 815 Manuel utilisateur
FLOWBIRD
FLOWBIRD CWT Compact Touch Manuel utilisateur
Demco
Demco SP7 Manuel utilisateur
Lathem
Lathem PC600 Series Manuel utilisateur
