Alpha Alpha CD Condensing Boiler Manuel utilisateur

Installation Instructions

Alpha CD Condensing Boiler

CDVertical FlueTerminal Assembly

Concentric (60/100) Flue System

(Kit Part No. 6.2000520)

KIT CONTENTS

1. GENERAL

Note: The CD Vertical flue terminal MUST ONLY be used with an Alpha CD condensing boiler.

a. The flue system must be installed in accordance with BS 5440:1;1990.

b. The boiler must be installed in accordance with the Installation instructions supplied with the CD boiler.

c. The vertical flue terminal assembly is equivalent to a 1 m length of flue.

d. Each 45° bend is equivalent to a 0.9 m length of flue.

Note: A 90° bend must not be used with the vertical flue.

e. Refer to the vertical flue options (Fig. 3) and ensure the flue length does not exceed the equivalent of 15 m

(including the terminal assembly).

f. Additional flue lengths of 0.75 m (CD flue extension, Part No. 6.2000750) are available for extending the flue up to a

maximum equivalent flue length of 15 m (including the terminal assembly).

g. The CD vertical flue terminal assembly may be connected directly to

the boiler adaptor. However, under no circumstances must it be

shortened.

h. To determine the actual length of flue required (L), measure the

distance from the top of the side panel to the weathering slate position

and subtract 640 mm for the terminal assembly, i.e. L = A - 640 mm

(see Fig. 3).

2. INSTALLATION

a. When the template is on the wall in the boiler position, continue the

vertical line from the centre of the flue hole to the roof/ceiling position.

Mark the centre position of the flue hole 165 mm from this line as

shown in Fig. 1.

b. Cut a hole and/or remove tiles so that there is at least a 150 mm

diameter hole in the roof. Ensure there is at least a 25 mm gap

between the outer duct and any combustible material. Fig. 1

Compiled and designed by Publications 2000, Tel (01670) 356211 11/03/D155

Fig. 3

c. Fit a 125 mm diameter weathering slate over the hole in

the roof. A suitable weathering slate (Part No.

6.1000380) is available from Alpha Therm Ltd.

d. Position the vertical terminal assembly into the

weathering slate ensuring that the slate is located under

the lip of the terminal as shown in Fig. 2.

Note: Ensure that the minimum distances are maintained

(see Fig. 3). Do not secure the terminal into position at

this stage.

e. Assemble the flue extensions together by locating the

inner duct into the seal joint and secure each extension

together with the clamps supplied (three screws). Ensure

that the clamps are positioned centrally over the joints.

Note: If it is required to cut an extension, DO NOT cut

the end of the inner duct that incorporates the seal joint.

Ensure the inner duct end without the seal joint is cut so

that it is 15 mm longer than the outer duct.

f. Connect the vertical terminal ducts to the flue assembly,

as shown in Fig. 2. Secure with the outer duct clamp

(three screws).

g. After assembling all of the ducts, check that the terminal

is correctly located above the roof.

Note: Ensure that the flue assembly is supported at roof

level using suitable brackets, and that the weathering

slate is fitted correctly. Fig. 2

These instructions have been carefully prepared but we reserve the right to

alter the specification at any time in the interest of product improvement.

Alpha Therm Limited.

NepicarHouse,LondonRoad,WrothamHeath,

Sevenoaks, Kent TN15 7RS

Tel: 0870 3001964

email: [email protected]

website: www.alpha-boilers.com

Table des matières

Autres manuels Alpha Chaudière

Alpha

Alpha 280E Manuel utilisateur

Alpha

Alpha GasSaver GS-1 Guide de l'utilisateur

Alpha

Alpha Pro Tec 115 Guide de l'utilisateur

Alpha

Alpha Alpha CB Boiler Manuel utilisateur

Alpha

Alpha Alpha Plus DH Units Mode d’emploi

Alpha

Alpha CB28X Manuel de service

Alpha

Alpha Alpha CB Boiler Manuel utilisateur

Alpha

Alpha Alpha HE CB25 Guide de l'utilisateur

Alpha

Alpha Alpha CD50 Manuel utilisateur

Alpha

Alpha CD Easy-Flue Series Manuel utilisateur

Alpha

Alpha Pro Tec Plus 50 Guide de l'utilisateur

Alpha

Alpha Alpha Plus DH Units Mode d’emploi

Alpha

Alpha E-Tec 15R Guide de l'utilisateur

Alpha

Alpha Alpha CD13R Guide de l'utilisateur

Alpha

Alpha Alpha CD50 Guide de l'utilisateur

Alpha

Alpha Alpha CD25C Manuel utilisateur

Alpha

Alpha 41 532 05 Guide de l'utilisateur

Alpha

Alpha ARES 440 Tec Guide de l'utilisateur

Alpha

Alpha Alpha 240 Boiler Range Manuel d'instructions et de sécurité

Alpha

Alpha Alpha CB24 Manuel utilisateur

Alpha

Alpha Alpha CD25C Manuel utilisateur

Alpha

Alpha Alpha CD50 Manuel utilisateur

Alpha

Alpha SolarSmart 90 Guide de l'utilisateur

Alpha

Alpha Alpha 240X Guide de l'utilisateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur