Allen-Bradley ControlNet PLC-5 Manuel utilisateur

1Publication 1785-IN022C-EN-P - September 2005

Installation Instructions

Firmware Update Instructions for Ethernet,

Enhanced and ControlNet PLC-5

Programmable Controllers

Purpose

This document describes how to update firmware on your Ethernet,

Enhanced, or ControlNet PLC-5 programmable controller.

Firmware Update Kit

Contents

Depending on your requirements, the firmware update kit may contain:

•ControlFLASH software with the firmware update

•these installation instructions

•applicable firmware release notes

•a firmware revision label

•firmware EPROMS, if applicable

Hardware and Software

Requirements

Your computer must meet the following requirements to perform the

firmware update:

•at least a 486 processor

•Windows 95, Windows 98, or Windows NT, or later, operating system

•at least 16 Mbytes of available memory

To perform Ethernet Series C, or later, firmware updates, you will need a

Network Interface Card and a switch, Ethernet hub or crossover cable.

To perform other updates, you need a shielded serial cable, either 1784-CP10

or 1784-CP11.

Locate Your Controller’s

Update Procedure in this

Document

ATTENTION

You must save the controller’s processor memory to your

hard disk or to an EEPROM. If you do not, the

controller’s user memory will be lost because the

firmware update procedure erases memory.

To update the firmware on this controller: Go to this page:

Ethernet PLC-5, Series C and D 4

Ethernet PLC-5, Series E or Later 13

Enhanced PLC-5, Series A thru D 21

Enhanced PLC-5, Series E or Later 25

ControlNet PLC-5, All Series 33

Allen-Bradley Motors

Publication 1785-IN022C-EN-P - September 2005

2Firmware Update Instructions for Ethernet, Enhanced and ControlNet PLC-5 Programmable Controllers

Important User Information

Solid state equipment has operational characteristics differing from those of

electromechanical equipment. Safety Guidelines for the Application, Installation and

Maintenance of Solid State Controls (Publication SGI-1.1 available from your local

Rockwell Automation sales office or online at http://www.ab.com/manuals/gi)

describes some important differences between solid state equipment and hard-wired

electromechanical devices. Because of this difference, and also because of the wide

variety of uses for solid state equipment, all persons responsible for applying this

equipment must satisfy themselves that each intended application of this equipment is

acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or

consequential damages resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes.

Because of the many variables and requirements associated with any particular

installation, Rockwell Automation, Inc. cannot assume responsibility or liability for

actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of

information, circuits, equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written

permission of Rockwell Automation, Inc. is prohibited.

Throughout this manual, when necessary we use notes to make you aware of safety

considerations.

WARNING Identifies information about practices or circumstances

that can cause an explosion in a hazardous environment,

which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT Identifies information that is critical for successful

application and understanding of the product.

ATTENTION Identifies information about practices or circumstances

that can lead to personal injury or death, property

damage, or economic loss. Attentions help you:

•identify a hazard

•avoid a hazard

•recognize the consequence

SHOCK HAZARD Labels may be located on or inside the equipment (e.g.,

drive or motor) to alert people that dangerous voltage may

be present.

BURN HAZARD Labels may be located on or inside the equipment (e.g.,

drive or motor) to alert people that surfaces may be

dangerous temperatures.

Publication 1785-IN022C-EN-P - September 2005

Firmware Update Instructions for Ethernet, Enhanced and ControlNet PLC-5 Programmable Controllers 3

ATTENTION Preventing Electrostatic Discharge

This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these

guidelines when you handle this equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wrist strap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•If available, use a static-safe workstation.

•When not in use, store the equipment in appropriate

static-safe packaging.

ATTENTION This version of ControlFLASH is only suitable for this firmware

update. Do not use this version of ControlFLASH to update

firmware on any other PLC-5 programmable controller.

Allen-Bradley Motors

Publication 1785-IN022C-EN-P - September 2005

4Firmware Update Instructions for Ethernet, Enhanced and ControlNet PLC-5 Programmable Controllers

Important Considerations for CL I, Div. 2 Installations

Ethernet PLC-5

Programmable Controllers

- 1785-L20E

- 1785-L40E

- 1785-L80E

Series C and D

To update these series of Ethernet PLC-5 firmware, you must first use

ControlFLASH through the Ethernet channel, and then replace the applicable

EPROMS. To start this firmware update, follow these steps:

Step 1 - Prepare the PLC-5 Programmable Controller

1. Save the controller’s processor memory to your hard disk or to an

EEPROM.

2. Remove power from the controller.

3. Remove the controller battery cover and disconnect the battery.

4. Remove the controller from the chassis.

WARNING When you connect or disconnect the battery, an electrical arc can

occur. This could cause an explosion in hazardous location

installations. Be sure that power is removed or the area is

nonhazardous before proceeding.

• For safety information on the handling of lithium batteries,

including handling and disposal of leaking batteries, refer to

Guidelines for Handling Lithium Batteries, publication AG-5.4

• Store batteries in a cool, dry environment. We recommend 25°

C with 40% or 60% relative humidity. You may store batteries

up to 30 days between -45° - 85° C, such as during

transportation. To avoid possible leakage, do not store batteries

above 60° C for more than 30 days.

WARNING When you install or remove the module with power applied, or

you connect or disconnect the serial cable with power applied to

this programmable controller or the device on the other end of

the cable, an electrical arc can occur. This could cause an

explosion in hazardous location installations. Be sure that power is

removed or the area is nonhazardous before proceeding.

ATTENTION

You must save the controller’s processor memory to your

hard disk or to an EEPROM. If you do not, the

controller’s user memory will be lost because the

firmware update procedure erases memory.

Publication 1785-IN022C-EN-P - September 2005

Firmware Update Instructions for Ethernet, Enhanced and ControlNet PLC-5 Programmable Controllers 5

5. Locate and document the controller’s hardware Ethernet address.

The address is on the circuit board label toward the back of the

controller.

6. If applicable, disconnect the coprocessor or Ethernet Interface sidecar

module.

7. Reinstall the controller into the chassis.

8. Apply power to the controller.

9. Through the Ethernet port, use either a switch, hub or crossover cable

to connect the computer to the controller. Make sure the TCP/IP is

configured and running on the personal computer.

10. Assign the controller’s IP address by going online with the controller via

DH+ or serially. Use the channel configuration screen to configure the

IP address for Channel 2 (uncheck the BOOTP enabled box).

11. Turn the controller keyswitch to PROGRAM mode.

Allen-Bradley Motors

Publication 1785-IN022C-EN-P - September 2005

6Firmware Update Instructions for Ethernet, Enhanced and ControlNet PLC-5 Programmable Controllers

Step 2 - Install the ControlFLASH Software

1. Insert the ControlFLASH disk into the floppy drive of your computer.

2. Browse the A: drive and select the setup.exe program.

3. If you have an earlier version of ControlFLASH installed, we

recommend to install this version into the same directory.

4. Follow the Setup Wizard as it guides you through the installation

process.

Step 3 - Perform the ControlFLASH Update

1. If you have not already done so, connect the computer to the controller

through the Ethernet channel:

–use either a switch, hub or crossover cable to connect the computer

to the controller

2. Close all applications including RSLinx.

ATTENTION

Failure to follow these procedures exactly or to

cause an interruption during them may result in

an inoperable controller.

Publication 1785-IN022C-EN-P - September 2005

Firmware Update Instructions for Ethernet, Enhanced and ControlNet PLC-5 Programmable Controllers 7

3. Start ControlFLASH:

3A - Start the ControlFLASH software.

3B - Select the appropriate PLC-5

Programmable Controller catalog number.

Click Next.

Use the cursor to highlight the PLC-5 type

Click Next.

Allen-Bradley Motors

Publication 1785-IN022C-EN-P - September 2005

8Firmware Update Instructions for Ethernet, Enhanced and ControlNet PLC-5 Programmable Controllers

3C - Enter the Ethernet IP address of the

PLC-5 you are updating.

3D - Select the firmware revision.

Click OK.

Select the correct update revision.

Click Finish.

3E - Verify the update.

Click Next.

Click Get Info to verify the

programmable controller

you are updating.

Publication 1785-IN022C-EN-P - September 2005

Firmware Update Instructions for Ethernet, Enhanced and ControlNet PLC-5 Programmable Controllers 9

4. Remove power from the controller.

5. Remove the controller from the chassis.

3F - Start the firmware update.

Click Yes.

The progress indicator shows how much of the

update has been performed.

Important: This update can take up to two minutes

to complete.

3H - Follow the power cycle instructions during and after the update process.

When the update is complete, the software will prompt

you to cycle power.

Important: Do not click OK until you complete the next

three steps:

- “Install the New Firmware EPROMS”

- “Apply the Firmware Revision Label”

- “Complete the Firmware Update”

These procedures are detailed on the following pages.

3G - Check the STAT LED on the PLC-5. If it is flashing green, the ControlFLASH update was

successful - continue to step 3H. If the STAT LED is not flashing green, the update was not

successful - call Rockwell Automation Technical Support at 440-646-3223.

Allen-Bradley Motors

Publication 1785-IN022C-EN-P - September 2005

10 Firmware Update Instructions for Ethernet, Enhanced and ControlNet PLC-5 Programmable Controllers

Step 4 - Install the New Firmware EPROMS

Note: Do not reinstall the controller until you complete the next step.

On the Ethernet PLC-5, Series C and D: Do this:

1785-L20E programmable controller 1. Remove the four screws that hold the right

side plastic cover.

2. Remove the cover.

3. Remove the two large screws and washers

located in the center of the exposed circuit

board.

4. Carefully separate the two processor

boards by pulling the exposed circuit board at

the backplane edge connector away from the

metal cover as you would open a book.

5. Remove and replace the firmware EPROMS

one at a time, taking note of the location

number and the orientation of the notch in

each of the EPROMS.

6. See the figure to the left for the numbers

and locations of the EPROMS.

7. Reassemble the controller by reversing

steps 1 thru 4.

1785-L40E and -L80E programmable controllers 1. On the front of the controller, remove the 2

hex nuts on Channel 0.

2. Remove the screw on the communication

card and gently pull the card out of the

controller.

3. Remove the four screws that hold the right

side plastic cover and remove the cover.

4. Remove the two large screws and washers

located in the center of the exposed circuit

board.

5. Carefully separate the two processor

boards by pulling the exposed circuit board at

the backplane edge connector away from the

metal cover as you would open a book.

6. Remove and replace the firmware EPROMS

one at a time, taking note of the location

number and the orientation of the notch in

each of the EPROMS.

7. See the figure to the left for the numbers

and locations of the EPROMS.

8. Reassemble the controller by reversing

steps 1 thru 5.

* EPROM numbers may vary and their locations shown in these illustrations are approximate. Your series and revision of controller and firmware may be different. Make certain the EPROM numbers

from your firmware update match the numbers on their respective circuit boards and communication cards.

U18*

U61*

U70*

Replace the

U61 and U70

EPROMS*

If applicable,

replace the U18

EPROM*

(if applicable)

U5*

U31* U7 or U12*

Replace the

U5 and U31

EPROMS on the

circuit board*

If applicable,

Remove communication card

replace the U7

or U12 EPROM

(if applicable)

on the

communication

card*

Autres manuels pour ControlNet PLC-5

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Allen-Bradley Contrôleurs

Allen-Bradley

Allen-Bradley PowerFlex 20-750-S1 Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 755TL Manuel utilisateur

Allen-Bradley

Allen-Bradley DriveLogix 5730 Manuel utilisateur

Allen-Bradley

Allen-Bradley MicroLogix 1400 Manuel utilisateur

Allen-Bradley

Allen-Bradley MicroLogix 1100 Manuel utilisateur

Allen-Bradley

Allen-Bradley 1756-L71 Manuel utilisateur

Allen-Bradley

Allen-Bradley CompactLogix 5370 L1 Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlNet PLC-5 Manuel utilisateur

Allen-Bradley

Allen-Bradley 1391B Series Manuel utilisateur

Allen-Bradley

Allen-Bradley 161S-AA04NPU Manuel utilisateur

Allen-Bradley

Allen-Bradley PLC-2/30 Manuel utilisateur

Allen-Bradley

Allen-Bradley powerflex 700 Manuel utilisateur

Allen-Bradley

Allen-Bradley GuardLogix Manuel utilisateur

Allen-Bradley

Allen-Bradley AADvance Manuel utilisateur

Allen-Bradley

Allen-Bradley iTRAK 5730 Manuel utilisateur

Allen-Bradley

Allen-Bradley SMC-3 Manuel utilisateur

Allen-Bradley

Allen-Bradley 2080-LC20-20QBB Manuel utilisateur

Allen-Bradley

Allen-Bradley powerflex 700 Manuel utilisateur

Allen-Bradley

Allen-Bradley SLC 500 Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 700S Manuel utilisateur

Allen-Bradley

Allen-Bradley 1305-RFB-5-A Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 700H Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 700S Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 523 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur