Allen-Bradley PLC-3 Series Manuel utilisateur
Quick Start
for Experienced
Users
PLC3 Family
Programmable
Controllers
AllenBradley
product icon
Because of the variety of uses for the products described in this
publication, those responsible for the application and use of this
control equipment must satisfy themselves that all necessary steps
have been taken to assure that each application and use meets all
performance and safety requirements, including any applicable laws,
regulations, codes and standards.
The illustrations, charts, sample programs and layout examples
shown in this guide are intended solely for purposes of example.
Since there are many variables and requirements associated with any
particular installation, Allen-Bradley does not assume responsibility
or liability (to include intellectual property liability) for actual use
based upon the examples shown in this publication.
Allen-Bradley publication SGI-1.1, Safety Guidelines for the
Application, Installation, and Maintenance of Solid-State Control
(available from your local Allen-Bradley office), describes some
important differences between solid-state equipment and
electromechanical devices that should be taken into consideration
when applying products such as those described in this publication.
Reproduction of the contents of this copyrighted publication, in
whole or in part, without written permission of Allen-Bradley
Company, Inc., is prohibited.
Throughout this manual we use notes to make you aware of safety
considerations:
!ATTENTION: Identifies information about practices
or circumstances that can lead to personal injury or
death, property damage or economic loss.
Attention statements help you to:
•identify a hazard
•avoid the hazard
•recognize the consequences
Important: Identifies information that is critical for successful
application and understanding of the product.
Important User
Information
Overview P-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using
this Quick Start
P-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What You Need to Do P-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Components used in this Quick Start P-2
. . . . . . . . . . . . . . . .
IfY
ou Need Help ...
P-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configure and Ground I/O and Processor Chassis 1-1. . . . . . .
Configure
I/O Chassis
1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configure Processor Chassis 1-2
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Ground Processor and I/O Chassis 1-2
. . . . . . . . . . . . . . . . . . . . . . .
Install
Power Supply
2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install1775P3 Power Supply into the PLC3/10
(or singlechassis PLC3) 2-1
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Install1775P1 Power Supply into the PLC3 2-3
. . . . . . . . . . . . . . . .
InstallProcessor
, Memory
, and Scanner Modules 3-1. . . . . . .
Connect Front Panel Cable and Install Processor 3-1. . . . . . . . . . . . .
InstallMemory Module(s) 3-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
InstallI/O Scanner Module(s) 3-2
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Install,Wire, and Connect I/O 4-1. . . . . . . . . . . . . . . . . . . . . . .
Installand Wire I/O Modules 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connect
I/O
4-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configure a Personal Computer 5-1. . . . . . . . . . . . . . . . . . . . .
Configure and Connect 1770T4 Programming Terminal 5-1. . . . . . . .
Connect to Personal Computer 5-2
. . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting and Specifications 6-1. . . . . . . . . . . . . . . . .
Powersupply Module Indicators 6-1. . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 6-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents
Preface
Publication 177510.1 - March 1996
Overview
This quick start is designed to help you quickly install and connect a
basic PLC-3 family programmable controller system. Use this guide
if you are knowledgeable about PLC-3 family products but may not
have used one or more of the products for a period of time. The
information we provide is geared to “jog your memory.”
b
step 1
2
3
step
step
a
b
a
Configure I/O chassis
(page 11)
Ground I/O chassis
(page 11)
a
b
Install 1775P3 power supply
(page 21)
Install memory module(s)
(page 41)
Install I/O scanner module(s)
(page 42)
Install the processor module
(page 41)
Install 1775P1 power supply
(page 23)
Connect front panel cable
(page 31)
For more information, see the PLC3 Programmable Controllers
Installation and Operations Manual, publication 17756.7.1.
PLC3
Controller
1775S5
Scanner
1775SR5
Scanner
PLC3/10
Controller
DH +
Link
For more
information...
cConfigure processor chassis
(page 41)
c
d
Install I/O and Processor Chassis
Install Power Supply
Install Modules
Using this Quick Start
What You Need to Do
OverviewP–2
Publication
177510.1 - March 1996
4step
a
b
5step
Install and wire I/O modules
(page 51)
Connect I/O to scanner
(page 52)
Configure and connect a programming terminal
(page 61)
Install and Connect I/O
Product name: Catalog number:
I/O chassis 1771A1B, A2B, A3B, A4B
power supply •1775P3 (PLC3/10)
•1775P1, P3 (PLC3)
processor chassis •1775A1, A2 (PLC3)
•1775A3 (PLC3/10)
front panel cable 1775CAK
processor •1775L4 (PLC3/10)
•1775L3 (PLC3)
memory module(s) •1775MS4, MS8, MSA, MSD (PLC3/10)
•1775ME4, ME8, MEA, MED, MEF (PLC3)
I/O scanner module(s) 1775S4A, S4B, S5, SR5, SR
I/O modules 1771IE
programming terminal 1770T4, 1784T45, T47, T50, IBMcompatible PC
using 6200 or AI series PLC3 programming software
PLC3 industrial terminal cable 1775CAT
Belden 8723 cable or equivalent 1778CR
25pin male connector kits 1770XXP
DH+ cable 1784CP
System Components
used in this Quick Start
Overview P–3
Publication
177510.1 - March 1996
If you need additional assistance in installing or connecting your
PLC-3 family programmable controller system, start with the
troubleshooting section in the appendix of this quick start. If you still
experience difficulty, call 1-800-9NEWLIT to order one of the
publications suggested below or contact your Allen-Bradley service
representative.
Publication title: Publication number:
PLC3 Programmable Controllers Installation and Operation Manual 17756.7.1
PLC3 Family Programmable Controllers Programming Reference Manual 17756.4.1
AllenBradley PLC3 Power Supply (1775P1) Product Data 17752.4
PLC3, 3/10 Family Memory Modules Installation Data 17752.27
PLC3/10 Power Supply Module Installation Instructions 17755.1
PLC3 Family I/O Scanner CommunicationAdapter Module User Manual 17756.5.5
I/O ScannerProgrammer Interface Module User's Manual 17756.5.2
I/O ScannerMessage Handling Module 17756.5.3
PLC3 Programmable Controller Backup Systems User Manual 1775-6.3.1
AB
If You Need Help ...
Step 1
Publication
177510.1 - March 1996
Configure and Ground I/O and
Processor Chassis
Configure I/O Chassis
12345678
O
N
O
F
F
First I/O group number
I/O rack number
Address Switch Assembly
(S1)
Switch Assembly (S2) Pressed in at top
Closed (ON)
Pressed in at bottom
Open (OFF)
O
N
O
F
F
1234 56
Switch Position
1 2
57.6K Baud 10,000ft
1
15.2K Baud 5,000ft
Not Used
Maximum
I/O
chassis distance Link Response ON for series B emulation
Scan On for all but last 4 slots
Off for all slots
OFF for unrestricted
Always OFF
ATTENTION: Link response switch must
be ON when using the following scanner modules:
1775S4A
1775S4B
1775S5
1775SR5
1775SR
ON OFF
OFF OFF
ON ON
ON
230.4K Baud 2,500ft
1
OFF
1230.4K
Baud with 1775S5 revision A/G and
later
, and 1775SR5 revision A/G and later
scanners only.
Off
Set the backplane switches.
a
Keying
Bands
Install keying bands.
b1771 I/O
Module
See the appropriate product data for the module
you are installing to determine the proper keying
positions for each module.
1–2
Configure and Ground I/O and Processor Chassis
Publication
177510.1 - March 1996
Configure Processor Chassis
Set the backplane switches located near the upper lefthand corner of the chassis backplane.
If you:
are not using expansion chassis
are using expansion chassis
number the chassis:
set the chassis number to 0
(processor module must be in chassis 0)
consecutively starting with 0
O
N
O
F
F
Switch:
123
Chassis Number
on
off
on on
onoff
off
off off
off
off
off
0
1
2
3
ATTENTION: Number the chassis so that chassis o and the highest
numbered chassis have the same power supply
. Failure to configure the
chassis in this way could result in unpredictable operation.
Ground Processor and I/O Chassis
Enclosure
Grounding electrode conductor
To grounding
electrode
system
Ground
bus
I/O chassis wall
Ground
lug Nut
Star
washer
Ground lug
Step 2
Publication
177510.1 - March 1996
Install Power Supply
Install 1775P3 Power Supply into the PLC3/10
(or singlechassis PLC3)
a
PLC3/10 chassis
CF2
CF1
backplane
20417M
Feed the dc power cable under the
module guides along the backplane.
Install
the dc power cable.
Squeeze the side tabs of the plugs
as you connect them to the backplane.
bPlug the cable assembly into the connectors on the powersupply module,
connect the 8pin control connector cable to the power
supply module, and
insert the power
supply module in the rightmost slot of the chassis.
PLC3/10 chassis
20418M
Insert and tighten all six screws
on the outside of the chassis.
P2 P1
1775P3
powersupply
module
Squeeze the side tabs of the plugs
as you connect them to the module.
Connect the cable
at the 8pin connector.
When
you install the 1775P3 power supply into a PLC3/10, if
there is a jumper plug (PN 96744701) installed on the
8pin controlconnector terminals, remove and discard it.
2–2
Install Power Supply
Publication
177510.1 - March 1996
Selector Switch Selector Switch
230V
115V
230V
115V
Terminal Strip Terminal Strip
L1
N
115V AC
L1
L2/N
GND
N.C.
COM.
N.O.
L1
L2
230V AC
L1
L2/N
GND
N.C.
COM.
N.O.
115V ac operation 230V ac operation
20419M
cSet
the voltage switch for the proper range.
!ATTENTION: Be
sure to set the voltage selection switch
properly or you may damage the powersupply module.
dConnect
the ac power line to the terminal strip on the power
supply module
and connect any relay wires, then insert the PLC3/10 module(s) into the
chassis and turn the ac power on.
e
Close the front door of the chassis and rotate the two retaining
screws approximately 21/2 turns counterclockwise.
f
Indicator Normal Operation Means
AC ON
AC OK
DC OK
red
green
green
ac power is supplied to the unit
ac line voltage is equal to or greater
than the required minimum ac voltage
the supply's internal dc voltages
are in their proper operating range
Turn
on dc power and make sure the indicators on the
powersupply module are lit as follows:
If
you don't see this, refer to chapter 8 for troubleshooting information.
Table des matières
Autres manuels Allen-Bradley Contrôleurs
Allen-Bradley
Allen-Bradley powerflex 700 Manuel utilisateur
Allen-Bradley
Allen-Bradley PowerFlex 700H Manuel utilisateur
Allen-Bradley
Allen-Bradley GuardPLC 1754 Manuel utilisateur
Allen-Bradley
Allen-Bradley PowerFlex 755TL Manuel utilisateur
Allen-Bradley
Allen-Bradley 1336 FORCE Manuel utilisateur
Allen-Bradley
Allen-Bradley Guard Master MSR22LM Manuel utilisateur
Allen-Bradley
Allen-Bradley ControlLogix 1756-HYD02 Manuel utilisateur
Allen-Bradley
Allen-Bradley PowerFlex 20-750-S1 Manuel utilisateur
Allen-Bradley
Allen-Bradley 1391B Series Manuel utilisateur
Allen-Bradley
Allen-Bradley 1336 PLUS II Manuel utilisateur
Allen-Bradley
Allen-Bradley SLC 500 Manuel utilisateur
Allen-Bradley
Allen-Bradley Logix5000 Series Manuel utilisateur
Allen-Bradley
Allen-Bradley MicroLogix 1000 Manuel utilisateur
Allen-Bradley
Allen-Bradley 1785-L11B Manuel utilisateur
Allen-Bradley
Allen-Bradley SLC 500 Manuel utilisateur
Allen-Bradley
Allen-Bradley micrologix 1500 Manuel utilisateur
Allen-Bradley
Allen-Bradley PowerFlex 700L Manuel utilisateur
Allen-Bradley
Allen-Bradley PLC-2/20 Guide de configuration
Allen-Bradley
Allen-Bradley Bulletin 505 Manuel utilisateur
Allen-Bradley
Allen-Bradley PowerFlex 70 Manuel utilisateur
