Allen-Bradley MicroLogix 1200 Manuel utilisateur

Publication 1762-IN016B-EN-P - December 2005

Installation Instructions

MicroLogix 1200 Analog Output Module

Catalog Number 1762-OF4

Inside...

For See Page

Important User Information 2

Before Installation 3

Prevent Electrostatic Discharge 3

Remove Power 4

Hazardous Location Considerations 4

Environnements dangereux 5

About the Analog Output Module 6

Install the Analog Output Module 7

Mount the Module on a DIN Rail 7

Mount the Module on a Panel 8

Wire the Analog Output Module 9

Ground the Module 10

System Assembly 12

I/O Memory Mapping 13

Input Data File 13

Output Data File 14

Configuration Data File 14

Specifications 17

Additional Resources 19

2MicroLogix 1200 Analog Output Module

Publication 1762-IN016B-EN-P - December 2005

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical equipment.

Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls publication

SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature describes some important differences between solid state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of the

wide variety of uses for solid state equipment, all persons responsible for applying this equipment must

satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many

variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot

assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING Identifies information about practices or circumstances that can cause an explosion in

a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

ATTENTION Identifies information about practices or circumstances that can lead to personal injury

or death, property damage, or economic loss. Attentions help you identify a hazard,

avoid a hazard and recognize the consequences.

SHOCK HAZARD

Labels may be located on or inside the equipment (e.g., drive or motor) to alert people

that dangerous voltage may be present.

BURN HAZARD

Labels may be located on or inside the equipment (e.g., drive or motor) to alert people

that surfaces may be dangerous temperatures.

MicroLogix 1200 Analog Output Module 3

Publication 1762-IN016B-EN-P - December 2005

Before Installation

1762 I/O is suitable for use in an industrial environment when installed in

accordance with these instructions. Specifically, this equipment is intended for use

in clean, dry environments (Pollution degree 2(1)) and to circuits not exceeding

Over Voltage Category II(2) (IEC 60664-1).(3)

Prevent Electrostatic Discharge

(1) Pollution Degree 2 is an environment where, normally, only non-conductive pollution occurs except that occasionally a

temporary conductivity caused by condensation shall be expected.

(2) Over Voltage Category II is the load level section of the electrical distribution system. At this level transient voltages are

controlled and do not exceed the impulse voltage capability of the product’s insulation.

(3) Pollution Degree 2 and Over Voltage Category II are International Electrotechnical Commission (IEC) designations.

ATTENTION Electrostatic discharge can damage integrated circuits or

semiconductors if you touch bus connector pins. Follow these

guidelines when you handle the module:

•Touch a grounded object to discharge static potential.

•Wear an approved wrist-strap grounding device.

•Do not touch the bus connector or connector pins.

•Do not touch circuit components inside the module.

•If available, use a static-safe work station.

•When not in use, keep the module in its static-shield box.

4MicroLogix 1200 Analog Output Module

Publication 1762-IN016B-EN-P - December 2005

Remove Power

Hazardous Location Considerations

This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D or

non-hazardous locations only. The following WARNING statement applies to use in

hazardous locations.

ATTENTION Remove power before removing or installing this module. When

you remove or install a module with power applied, an electrical

arc may occur. An electrical arc can cause personal injury or

property damage by:

•sending an erroneous signal to your system’s field devices,

causing unintended machine motion,

•causing an explosion in a hazardous environment, or

•causing permanent damage to the module’s circuitry.

Electrical arcing causes excessive wear to contacts on both the

module and its mating connector. Worn contacts may create

electrical resistance.

WARNING EXPLOSION HAZARD

•Substitution of components may impair suitability for Class I,

Division 2.

•Do not replace components or disconnect equipment unless

power has been switched off.

•Do not connect or disconnect components unless power has

been switched off.

•This product must be installed in an enclosure.

•In Class I, Division 2 applications, the bus connector must be

fully seated and the bus connector cover must be snapped in

place.

•In Class I, Division 2 applications, all modules must be

mounted in direct contact with each other as shown on

page 7. If DIN rail mounting is used, an end stop must be

installed ahead of the controller and after the last 1762 I/O

module.

•All wiring must comply with N.E.C. article 501-4(b).

MicroLogix 1200 Analog Output Module 5

Publication 1762-IN016B-EN-P - December 2005

Environnements dangereux

Cet équipement est conçu pour être utilisé dans des environnements de Classe 1,

Division 2, Groupes A, B, C, D ou non dangereux. La mise en garde suivante

s’applique à une utilisation dans des environnements dangereux.

WARNING DANGER D’EXPLOSION

•La substitution de composants peut rendre cet équipement

impropre à une utilisation en environnement de Classe 1,

Division 2.

•Ne pas remplacer de composants ou déconnecter

l'équipement sans s'être assuré que l'alimentation est coupée.

•Ne pas connecter ou déconnecter des composants sans s'être

assuré que l'alimentation est coupée.

•Ce produit doit être installé dans une armoire.

•Pour les applications de Classe I, Division 2, le connecteur de

bus doit être correctement installé et son couvercle

enclenché.

•Pour les applications de Classe 1, Division 2, tous les modules

doivent être installés en contact direct les uns avec les autres,

comme indiqué page 7. Si on utilise le montage sur rail DIN,

une butée doit être placée à l'avant de l'automate et après la

dernière unité d'E/S 1762.

6MicroLogix 1200 Analog Output Module

Publication 1762-IN016B-EN-P - December 2005

About the Analog Output Module

Figure 1 Product Description

Item Description Item Description

1a upper panel mounting tab 5 bus connector cover

1b lower panel mounting tab 6 flat ribbon cable with bus connector

(female)

2 power diagnostic LED 7 terminal block

3 module door with terminal identification

label

8 DIN rail latch

4 bus connector

with male pins

9 pull loop

MicroLogix 1200 Analog Output Module 7

Publication 1762-IN016B-EN-P - December 2005

Install the Analog Output Module

Maintain spacing from enclosure walls, wireways and adjacent equipment. Allow

50.8 mm (2 in.) of space on all sides for adequate ventilation, as shown:

Figure 2 Module Spacing

Mount the Module on a DIN Rail

The module can be mounted using the following DIN rails: 35 x 7.5 mm

(1.38 x 0.30 in.) (EN 50 022 - 35 x 7.5)

or 35 x 15 mm (1.38 x 0.60 in.) (EN 50 022 - 35 x 15).

ATTENTION Do not remove protective debris strip until after the module and

all other equipment near the module is mounted and wiring is

complete. Once wiring is complete and the module is free of

debris, carefully remove protective debris strip. Failure to remove

strip before operating can cause overheating.

TIP 1762 expansion I/O is only mounted horizontally.

ATTENTION During panel or DIN rail mounting of all devices, be sure that all

debris (for example, metal chips and wire strands) is kept from

falling into the module. Debris that falls into the module could

cause damage when power is applied to the module.

Side Side

Top

Bottom

MicroLogix

1200

1762 I/O

8MicroLogix 1200 Analog Output Module

Publication 1762-IN016B-EN-P - December 2005

Before mounting the module on a DIN rail, close the DIN rail latch. Press the DIN

rail mounting area of the module against the DIN rail. The latch will momentarily

open and lock into place.

Use DIN rail end anchors (Allen-Bradley part number 1492-EA35 or 1492-EAH35)

for environments with vibration or shock concerns.

Figure 3 DIN Rail Mount

Mount the Module on a Panel

Use the dimensional template to mount the module. The preferred mounting

method is to use two M4 or #8 panhead screws per module. M3.5 or #6 panhead

screws may also be used, but a washer may be needed to ensure a good ground

contact. Mounting screws are required on every module.

TIP For environments with extreme vibration and shock concerns, use

the panel mounting method described below, instead of DIN rail

mounting.

End Anchor

MicroLogix 1200 Analog Output Module 9

Publication 1762-IN016B-EN-P - December 2005

Figure 4 Dimensional Template

Wire the Analog Output Module

The output type selection, current or voltage, is made by wiring to the appropriate

terminals, Iout or Vout, and by the type/range selection bits in the Configuration

Data File (see page 14).

Consider the following when wiring your system:

•The analog common (COM) is not connected to earth ground inside the

module. All terminals are electrically isolated from the system.

•Channels are not isolated from each other.

•Use Belden 8761, or equivalent, shielded wire.

•Under normal conditions, the drain wire (shield) should be connected to the

metal mounting panel (earth ground). Keep shield connection to earth

ground as short as possible.

•To ensure optimum accuracy for voltage type outputs, limit overall cable

impedance by keeping all analog cables as short as possible. Locate the I/O

system as close to your voltage type sensors or actuators as possible.

ATTENTION Analog outputs may fluctuate for less than a second when power

is applied or removed. This characteristic is common to most

analog outputs. While the majority of loads will not recognize this

short signal, it is recommended that preventive measures be taken

to ensure that connected equipment is not affected.

(3.54)

100

(3.94)

40.4

(1.59)

40.4

(1.59)

14.5

(0.57)

For more than 2 modules: (number of modules - 1) x 40.4 mm (1.59 in.)

NOTE:

Hole spacing tolerance:

±0.4 mm (0.016 in.).

MicroLogix 1200

Expansion I/O

MicroLogix 1200

Expansion I/O

MicroLogix 1200

Expansion I/O

MicroLogix 1200

10 MicroLogix 1200 Analog Output Module

Publication 1762-IN016B-EN-P - December 2005

Figure 5 Terminal Block Layout

Figure 6 Differential Sensor Transmitter Types

A write-on label is provided with the module. Mark the identification of each

terminal with permanent ink, and slide the label back into the door.

Ground the Module

This product is intended to be mounted to a well-grounded mounting surface such

as a metal panel. Additional grounding connections from the module’s mounting

tabs or DIN rail (if used) are not required unless the mounting surface cannot be

TIP Grounding the cable shield at the module end only usually

provides sufficient noise immunity. However, for best cable shield

performance, earth ground the shield at both ends, using a 0.01

µF capacitor at one end to block AC power ground currents, if

necessary.

V out 3

V out 2

V out 1

V out 0

I out 3

I out 2

I out 1

I out 0

COM

COM Commons connected

internally.

I out 0

I out 1

V out 2

V out 3

V out 0

V out 1

COM

I out 3

I out 2

COM

Current Load

Voltage Load

Autres manuels pour MicroLogix 1200

Table des matières

Autres manuels Allen-Bradley Unité de contrôle

Allen-Bradley

Allen-Bradley Logix5000 Series Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix 1756-OA8D Manuel utilisateur

Allen-Bradley

Allen-Bradley SLC 5/02 Manuel utilisateur

Allen-Bradley

Allen-Bradley ArmorBlock Series Manuel

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-12X4M12QCDR Manuel

Allen-Bradley

Allen-Bradley C Series Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFM Manuel utilisateur

Allen-Bradley

Allen-Bradley C Series Manuel utilisateur

Allen-Bradley

Allen-Bradley 1747-KE Manuel utilisateur

Allen-Bradley

Allen-Bradley 1734-OB2 Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 750 Series Manuel utilisateur

Allen-Bradley

Allen-Bradley 1757-ABRIO Manuel utilisateur

Allen-Bradley

Allen-Bradley 1407-CGCM-DLR Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix 1756-OX8I Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlNet ControlLogix 1756 Manuel utilisateur

Allen-Bradley

Allen-Bradley DeviceNet 1771-SDN/C Manuel utilisateur

Allen-Bradley

Allen-Bradley 1784-KT2/C Guide d'installation et d'utilisation

Allen-Bradley

Allen-Bradley SLC 500 BASIC Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix ControlNet Scanner Module Manuel de service

Allen-Bradley

Allen-Bradley 1407-CGCM Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix 1756-OA8 Manuel utilisateur

Allen-Bradley

Allen-Bradley Bulletin 160 DeviceNet Manuel utilisateur

Allen-Bradley

Allen-Bradley POINT I/O 1734-OB2 Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix 1756-DMD30 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur