Allen-Bradley E Series Manuel utilisateur

Publication1756-IN604A-EN-P - February 2006

Installation Instructions

ControlLogix ControlNet Interface Module

Catalog Numbers 1756-CNB, 1756-CNBR, Series E

Contents

About This Publication

Use this document as a guide to install the ControlLogix ControlNet Bridge

module.

For See Page

Important User Information 2

European Hazardous Location Approval 3

North American Hazardous Location Approval 4

Environment and Enclosure 5

Prevent Electrostatic Discharge 6

About the 1756-CNB and 1756-CNBR Series E Modules 6

Understand Standalone and Redundant Control 7

Before You Begin 8

Install or Remove the Module Under Power 14

Install the Module 15

Remove the Module 16

Connect the Module to the Network 17

Troubleshoot the Module 23

Interpret the Module Status Indicator and Display 24

ControlNet Network Channel Status Indicators 28

Specifications 30

Rockwell Automation Support BackCover

2ControlLogix ControlNet Interface Module

Publication 1756-IN604A-EN-P - February 2006

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1available from your local Rockwell Automation sales office or online at

http://literature.rockwellautomation.com/) describessome importantdifferences between solid state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of

the wide variety of uses for solid state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is acceptable.

InnoeventwillRockwellAutomation,Inc.be responsibleorliableforindirectorconsequentialdamages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by RockwellAutomation, Inc.with respect touse of information, circuits,

equipment, or software described in this manual.

Reproductionof the contents of thismanual, inwhole or inpart, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notesto make you aware of safety considerations.

WARNING Identifiesinformationaboutpracticesorcircumstancesthatcancauseanexplosionin

a hazardous environment, which may lead to personalinjury or death, property

damage, or economic loss.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

ATTENTION Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, oreconomic loss. Attentions helpyou identify a

hazard, avoid ahazard, and recognize the consequences.

HOCK HAZARD Labels may be located on or inside the equipment (for example, driveor motor) to

alert people that dangerous voltage may be present.

BURN HAZARD Labels may be located on or inside the equipment (for example, driveor motor) to

alert people that surfaces may be dangerous temperatures.

ControlLogix ControlNet Interface Module 3

Publication 1756-IN604A-EN-P - February 2006

European Hazardous Location Approval

European Zone 2 Certification

(The following applies when the product bears the EEx Marking.)

This equipment is intended for use in potentially explosive atmospheres as

defined by European Union Directive 94/9/EC.

The LCIE (Laboratoire Central des Industries Electriques) certifies that this

equipment has been found to comply with the Essential Health and Safety

Requirements relating to the design and construction of Category 3

equipment intended for use in potentially explosive atmospheres, given in

Annex II to this Directive. The examination and test results are recorded in

confidential report No. 28 682 010.

Compliance with the Essential Health and Safety Requirements has been

assured by compliance with EN 50021.

IMPORTANT This equipment is not resistant to sunlight or other sources of UV

radiation.

The secondary of a current transformer shall not be open-circuited

when applied in Class I, Zone2 environments.

Equipment of lesser Enclosure Type Rating must be installed in an

enclosure providing at least IP54 protection when applied in Class

I, Zone 2 environments.

Thisequipmentshallbeusedwithinitsspecifiedratingsdefinedby

Allen-Bradley.

Provision shall be made to prevent the rated voltage from being

exceeded by transient disturbances of more than 40% when

applied in Class I, Zone 2 environments.

4ControlLogix ControlNet Interface Module

Publication 1756-IN604A-EN-P - February 2006

North American Hazardous Location Approval

The following information applies when

operating this equipment in hazardous

locations:

Informations sur l'utilisation de cet équipement en

environnements dangereux:

Products marked “CL I, DIV 2, GP A, B, C, D” are

suitableforuseinClassIDivision2GroupsA, B,

C, D, Hazardous Locations and nonhazardous

locations only. Each product is supplied with

markingson theratingnameplateindicatingthe

hazardous location temperature code. When

combining products within a system, the most

adverse temperature code (lowest “T” number)

may be used tohelp determine the overall

temperature code of the system. Combinations

of equipment in your system are subject to

investigation by the local Authority Having

Jurisdiction at the time of installation.

Les produits marqués “CL I, DIV 2, GPA, B, C, D” ne

conviennent qu'à une utilisation en environnements

de Classe I Division 2 Groupes A, B, C, D dangereux

et non dangereux. Chaque produit est livré avec des

marquages sursa plaque d'identification qui

indiquent le code de température pour les

environnements dangereux. Lorsque plusieurs

produits sont combinés dans un système, le code de

température leplus défavorable (code de

température le plus faible) peut être utilisé pour

déterminer le code de température global du

système. Les combinaisons d'équipements dans le

système sont sujettes à inspection par les autorités

locales qualifiées au moment de l'installation.

EXPLOSION HAZARD

Donotdisconnectequipment

unless power has been

removedortheareaisknown

to be nonhazardous.

Do not disconnect

connections to this

equipment unless power has

been removed or the area is

known to be nonhazardous.

Secure any external

connections that mate to this

equipment by using screws,

sliding latches, threaded

connectors,or other means

provided with this product.

Substitution of components

may impair suitability for

Class I, Division 2.

If this product contains

batteries, they must only be

changed in an area known to

be nonhazardous.

RISQUE D'EXPLOSION

Couper le courant ou s'assurer

que l'environnement est classé

non dangereuxavant de

débrancher l'équipement.

Couper le courant ou s'assurer

que l'environnement est classé

non dangereuxavant de

débrancher les connecteurs.

Fixer tous les connecteurs

externes reliés à cet

équipement à l'aide de vis,

loquets coulissants,

connecteurs filetés ou autres

moyensfournis avec ce produit.

La substitution de composants

peut rendre cet équipement

inadapté à une utilisation en

environnement de Classe I,

Division 2.

S'assurer que l'environnement

estclassénondangereuxavant

de changer les piles.

WARNING AVERTISSEMEN

ControlLogix ControlNet Interface Module 5

Publication 1756-IN604A-EN-P - February 2006

Environment and Enclosure

ATTENTION This equipment is intended for use in a Pollution Degree 2 industrial

environment,inovervoltageCategoryIIapplications(asdefinedinIEC

publication60664-1),ataltitudesupto2000meterswithoutderating.

This equipment is considered Group 1, Class A industrial equipment

according to IEC/CISPR Publication 11. Without appropriate

precautions, there may be potential difficulties ensuring

electromagnetic compatibility in other environments due to

conducted as well as radiated disturbance.

This equipment is supplied as open-type equipment. It must be

mounted within an enclosure that is suitably designed for those

specific environmental conditions that will be present and

appropriately designed to prevent personal injury resulting from

accessibility to live parts. The interior of the enclosure must be

accessible only by the use of a tool. Subsequent sections of this

publication may contain additional information regarding specific

enclosure type ratings that are required to comply with certain

product safety certifications.

NOTE: See NEMA Standards publication 250 and IEC publication

60529, as applicable, for explanations of the degrees of protection

provided by different types of enclosure. Also, see the appropriate

sections in this publication, as well as Industrial Automation Wiring

and Grounding Guidelines, Allen-Bradley publication 1770-4.1, for

additional installation requirements pertaining to this equipment.

6ControlLogix ControlNet Interface Module

Publication 1756-IN604A-EN-P - February 2006

Prevent Electrostatic Discharge

For additional information, refer to Industrial Automation Wiring and

Grounding Guidelines, publication 1770-4.1.

About the 1756-CNB and 1756-CNBR Series E Modules

The 1756-CNB and 1756-CNBR Series E modules work for all nonredundant

ControlLogix applications.

ATTENTION This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these

guidelines when you handle this equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•If available, use a static-safe workstation.

•Whennot inuse, storethe equipmentinappropriatestatic-safe

packaging.

IMPORTANT Only the 1756-CNB and 1756-CNBR, Series D modules are

supported in ControlLogix Redundancy releases 8, 11, 13, and 15.

After a firmware upgrade to version 11.xx, Series E will be

supported in ControlLogix Redundancy release 15 or later.

You cannot upgrade a Series D module to a Series E module.

ControlLogix ControlNet Interface Module 7

Publication 1756-IN604A-EN-P - February 2006

Understand Standalone and Redundant Control

You can use the 1756-CNB and 1756-CNBR Series E modules as standalone

or in firmware version 11.xx as redundant control. For standalone control,

only one set of modules is required. For redundant control, two ControlLogix

chassis are populated with identical pairs of modules called partners. The

chassis that performs active control is called the primary chassis and the

modules in the chassis are called primary modules. The other chassis is called

the secondary chassis and the modules in the chassis are called secondary

modules. These installation instructions discuss both standalone and

redundant control; read them carefully to distinguish the procedures and

requirements for each type of control.

IMPORTANT If you use redundant control, you must select the same ControlNet

network address for each set of partner modules. You must also

place the partner modules in the same corresponding slots in their

respective redundant control chassis pair.

Primary Chassis

Secondary Chassis

RedundantControl

Chassis Pair

I/O Chassis

1756-SRM

1756-CNB/CNBR

ControlNet

Network

1756-SRM

1756-CNB/CNBR

1756-CNB

1756-CNBR

1756-CNB

1756-CNBR

1756-CNB

1756-CNBR

8ControlLogix ControlNet Interface Module

Publication 1756-IN604A-EN-P - February 2006

Before You Begin

Before you install the module you need to make sure you:

•Know how to handle the module.

Refer to the section Prevent Electrostatic Discharge.

•Have all of the necessary components:

•Know the type of ControlNet network:

There are two types of scheduled traffic networks for ControlNet:

single-keeper networks and multi-keeper networks.

1756-CNB or 1756-CNBR 1756-A4, 1756-A7, 1756-A10,

1756-A13, or 1756-A17 1756-PA72/75 or 1756-PB72/7

Power Supply

1786-TPR,1786 -TPS

1786-TPYR, or1786 -TPYS(1)

(1) 1786-TPS or 1786-TPYS taps recommended for network connections.

1786-TP (temporary

network connections)

Small Screwdriver (optiona

ControlLogix ControlNet Interface Module 9

Publication 1756-IN604A-EN-P - February 2006

All 1756-CNB and 1756-CNBR modules are keeper-capable, as listed.

You must match the keeper to the type of network, or upgrade the

firmware of the module at MAC ID 01 to be multi-keeper capable.

Refer to the ControlNet Modules in Logix5000 Control Systems User

Manual, publication CNET-UM001, for more information.

1756-CNB and 1756-CNBR Major/Minor Revision Keeper Type

A 1.xx Single-keeper

B 2.xx Multi-keeper

C 3.xx Single-keeper

C 4.xx Multi-keeper

D 5.xx Multi-keeper

D 7.xx Multi-keeper

E 10.xx Multi-keeper

E 11.xx Multi-keeper

10 ControlLogix ControlNet Interface Module

Publication 1756-IN604A-EN-P - February 2006

Identify Module Features

Refer to the figure Module Features to identify the hardware components of

the 1756-CNB and 1756-CNBR modules.

Module Features

Backplane

Connector

Front View Side View

Switches

Network Address

Module Status

Alphanumeric

Display

Module

Status

Indicator

ControlNet

Network

Channel Status

Indicators

Network

Access Port

Channel B

BNC Connector

(1756-CNBR only) Channel A

BNC Connector

Channel A

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Allen-Bradley Unité de contrôle

Allen-Bradley

Allen-Bradley DF1 Instructions de montage

Allen-Bradley

Allen-Bradley 1718 Ex I/O Manuel utilisateur

Allen-Bradley

Allen-Bradley C Series Manuel utilisateur

Allen-Bradley

Allen-Bradley 1203-GD1 Manuel de la liste des pièces

Allen-Bradley

Allen-Bradley ControlLogix 1756-IA8D Manuel utilisateur

Allen-Bradley

Allen-Bradley SLC 500 BASIC Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet 1756-DNB Manuel utilisateur

Allen-Bradley

Allen-Bradley DF1 Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFM Manuel utilisateur

Allen-Bradley

Allen-Bradley Bulletin 160 DeviceNet Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix 1756-PLS Manuel utilisateur

Allen-Bradley

Allen-Bradley 1756-L7 Series Manuel utilisateur

Allen-Bradley

Allen-Bradley SERCOS 1756-M03SE/A Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix 1756-HYD02 Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFM Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix ControlNet Scanner Module Manuel de service

Allen-Bradley

Allen-Bradley 1756 ControlLogix Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlNet-to-DeviceNet 1788-CN2DN Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlNet FLEX Ex 1797-BCNR Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet 1756-DNB Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet 1756-DNB Feuille d'instructions

Allen-Bradley

Allen-Bradley 1770-KFDG Manuel utilisateur

Allen-Bradley

Allen-Bradley 1746-HSTP1 Manuel utilisateur

Allen-Bradley

Allen-Bradley Rockwell Automation 1734-4IOL Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur