Allen-Bradley 2711P-RN6K Manuel utilisateur

Installation Instructions

Communication Modules

Catalog Numbers 2711P-RN6, 2711P-RN6K, 2711P-RN15S, 2711P-RN15SK

About This Publication

This document provides instructions on how to install or replace a communication module on a

PanelView Plus 700, 1000, 1250, or 1500 terminal.

The communication module installs over the logic module. The installation is the same for all

communication modules regardless of communication type.

Additional Resources

You can view or download publications at

http://www.rockwellautomation.com/literature/. To order paper copies of technical

documentation, contact your local Rockwell Automation distributor or sales

representative.

Topic Page

Important User Information 2

Install a Communication Module 3

Install a Communication Module 4

Cat. No.(1)

(1) These installation instructions also apply to other cat. no. 2711P-RNxx communication modules.

Communication Conformal

Coated Marine

Certified

DH+ DH-485 Remote I/O(2)

(2) Only supported on PanelView Plus 700 to 1500 terminals running FactoryTalk View Machine Edition software,

version 5.1 or earlier.

ControlNet

2711P-RN6 • • • •

2711P-RN6K • • • •

2711P-RN15S • •

2711P-RN15SK • •

IMPORTANT The logic module must be attached to a PanelView Plus display module before you attach

the communication module.

Spare Allen-Bradley Parts

2Communication Modules

Rockwell Automation Publication 2711P-IN003D-EN-P - June 2010

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical equipment.

Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1

available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between solid-state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide

variety of uses for solid-state equipment, all persons responsible for applying this equipment must satisfy

themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many

variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot

assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid

a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to

alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, drive or motor, to

alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of the

product.

Communication Modules 3

Rockwell Automation Publication 2711P-IN003D-EN-P - June 2010

Install a Communication Module

Follow these steps to install a new communication module.

1. Disconnect power from the terminal.

2. If the display module is removed from the panel, set the terminal, display side down, on a

clean, flat, stable surface.

3. Position the communication module over the logic module so that the connector on the

bottom of the communication module aligns with the connector on the logic module.

4. To prevent ESD between the modules, allow the communication module to touch the

logic module before making the connection.

WARNING: Explosion Hazard

Do not connect or disconnect any communication cable with power applied to

this device or any device on a network. An electrical arc could cause an

explosion in hazardous location installations. Be sure power is removed or the

area is known to be nonhazardous before proceeding.

ATTENTION: Work in a static-free environment and wear a properly grounded

electrostatic discharge (ESD) wristband. Do not touch the communication

module connector or its internal circuitry to avoid ESD.

TIP Logic module might look different depending on catalog number.

Connector for

Communication Module

Connector

Communication Module

Logic Module

Spare Allen-Bradley Parts

Rockwell Automation Publication 2711P-IN003D-EN-P - June 2010 PN-77996

Allen-Bradley, DH+, FactoryTalk View Machine Edition, PanelView Plus, Rockwell Software, and Rockwell Automation are trademarks of

Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400

5. Push down on the communication module until the connectors are seated.

6. Tighten the four screws that

secure the communication

module to the logic module

to a torque of 0.58 N•m

(5…7 lb•in).

Replace a Communication Module

Follow these steps to replace a communication module.

1. Disconnect power from the terminal.

2. Disconnect communication cables from the module.

3. Remove the four screws that secure the communication module.

4. Carefully lift the communication module away from the logic module.

5. Install the new communication module by following steps 3…6 under Install a

Communication Module on page 3.

WARNING: Explosion Hazard

Do not connect or disconnect any communication cable with power applied to

this device or any device on a network. An electrical arc could cause an

explosion in hazardous location installations. Be sure power is removed or the

area is known to be nonhazardous before proceeding.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Allen-Bradley Unité de contrôle

Allen-Bradley

Allen-Bradley ControlLogix 1756-ENET/B Manuel utilisateur

Allen-Bradley

Allen-Bradley PowerFlex 755 Manuel utilisateur

Allen-Bradley

Allen-Bradley Sipha 440N-S32013 Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix 1756-OA8 Manuel utilisateur

Allen-Bradley

Allen-Bradley 1771-ODD Manuel utilisateur

Allen-Bradley

Allen-Bradley POINT I/O PROFIBUS 1734-APB Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix ControlNet B Series Manuel utilisateur

Allen-Bradley

Allen-Bradley POINT I/O 1734-OB2 Manuel utilisateur

Allen-Bradley

Allen-Bradley MicroLogix 1200 Manuel utilisateur

Allen-Bradley

Allen-Bradley POINT I/O 1734-PDN Manuel utilisateur

Allen-Bradley

Allen-Bradley 1203-GD2 Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlNet-to-DeviceNet 1788-CN2DN Manuel utilisateur

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-12X4M12QCDR Manuel

Allen-Bradley

Allen-Bradley 1440-DYN02-01RJ Manuel utilisateur

Allen-Bradley

Allen-Bradley 1747-ASB Manuel utilisateur

Allen-Bradley

Allen-Bradley SLC 500 DeviceNet Manuel utilisateur

Allen-Bradley

Allen-Bradley ControlLogix 1756-DMD30 Manuel utilisateur

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-8IOLM12R Manuel utilisateur

Allen-Bradley

Allen-Bradley 1791-16BC Manuel utilisateur

Allen-Bradley

Allen-Bradley 1407-CGCM Manuel utilisateur

Allen-Bradley

Allen-Bradley ProcessLogix R300.1 Manuel utilisateur

Allen-Bradley

Allen-Bradley Logix5000 Series Manuel utilisateur

Allen-Bradley

Allen-Bradley 1771-OFE Manuel utilisateur

Allen-Bradley

Allen-Bradley 1747-KE Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur