ALE Coral 144 Manuel utilisateur
ALE Design • Print • Trace 03/12/2010
Disclaimer
This manual contains instructions for operating the ALE Coral 140 printer.
Read it carefull before performing an manipulation.
All service operations should be undertaken b qualified personnel onl .
Contact-us if ou need training for our equipment.
All information written in this Operator Manual was correct at the time
indicated in the version table below. However, the continual enhancement of
our products ma result in some differences existing between the
information contained in this document and our equipment.
Cop right © 2010 ALE Sarl, all rights reserved. Reproducing this manual in
whole or part without permission is expressl prohibited.
RiX® and TraceX® are registered trademarks of ALE sarl.
All trademarks in this document belong to their respective owners.
Version histor :
Date: Revision: Modifications: Author:
03/12/10 First version Onl solvant version AF
Coral 144 Operator Manual i
ALE Design • Print • Trace 03/12/2010
Contents
Disclaimer i
Contents ii
Notes iii
1 Description 1
1.1 Print-head description 1
1.2 Numbering 1
1.3 Dimensions 3
1.4 Alarm LEDs 4
2 Start Up 4
2.1 On line installation 4
2.1.1 Defining the position of the s stem 5
2.1.2 Installing the s stem along the conve or 6
2.1.3 Photocell installation 6
2.1.4 Encoder installation 7
2.2 Inking up for the first time "from dr " 8
2.3 Print-heads alignment 12
3 Printer operation 13
3.1 Ink bottle replacement 13
3.2 Printer service 13
4 Controller usage 13
4.1 Change parameters 13
4.2 Make a message 14
Coral 144 Operator Manual ii
ALE Design • Print • Trace 03/12/2010
Notes
Coral 144 Operator Manual iii
ALE Design • Print • Trace 03/12/2010
1 Description
1.1 Print-head description
Features:
–142mm print-band
–C an, Magenta, Yellow and Black colours (CMYK)
–print-forward onl
–uses ALE 250mL ink bottles
–304 Stainless steel enclosure
–IEEE1394 data cables (to connect with a MasterSeries controller)
On top of the Coral 144 print-head are 8 alarm LEDs. See 1.4 Alarm LEDs for
information.
1.2 Numbering
Each of the 8 printing channels is numbered (print-engine, Alarm LED, cable, ink
reservoir), as described b the following drawings.
Coral144 Operator Manual 1
Fig. 2: 24x M5 mounting holes underneath
ALE Design • Print • Trace 03/12/2010
Coral144 Operator Manual 2
Fig. 3: print-engines numbering (front view)
1
2
3
4
5
86
7
Fig. 4: ink circuits numbering
2
3
4
5
6
7
8
1
1
2
3
4
5
6
7
8
ALE Design • Print • Trace 03/12/2010
1.4 Alarm LEDs
There are eight red alarm LEDs on top of the print-head. Each one corresponds to an
ink bottle (See 1.2 for numbering). It starts blinking when the level of ink is too low in
the corresponding reservoir, which means that the bottle of ink is empt . Replace it b
following the steps described in 3.1.Ink bottle replacement
After a configured number of prints, if the ink level is still low in the reservoir, the
controller stops the printing (to avoid defective printings). See the controller manual for
information on configuring the number of prints after the ink-low signal.
When the ink low is detected, the print-head sends an alarm signal to the controller,
which can transfer it to an external device such as a PLC. See controller manual for
details.
2 Start Up
2.1 On line installation
Coral144 Operator Manual 4
Fig. 7: Coral 144 bottom dimensions with M5 mounting points
ALE Design • Print • Trace 03/12/2010
2.1.1 Defining the position of the s stem
After unpacking the printer and checking that the contents correspond to our order and
to the deliver note, the first operation will be to set the position of the print-head on the
conve or. The correct print-head position can be determined using Codex and its 3D
capabilities (Fig. 8). Please refer to the Codex manual for details.
You must know that the s stem must be adjusted so that the surfaces to be printed don't
touch the print-head, and are at a maximum distance of 3mm (Fig. 9).
Evaluate, then set precisel the product distance several times before “inking up” the
printer and printing messages ! We strongl recommend fitting product guide rails.
Coral144 Operator Manual 5
Fig. 8: CodeX 3D view with a 72mm print-head
ALE Design • Print • Trace 03/12/2010
Don't hesitate to contact our distributor in case ou have an questions regarding the
position of the printer.
2.1.2 Installing the s stem along the conve or
Due to the risk of vibration, it is not recommended to fix the printer directl onto
the conve or.
Install the controller and connect it to the print-head using the supplied IEEE1394 cables
but do not power on.
When the final position of the print-head along the conve or is determined, the next
step is to “ink up” the Coral print-head, as it is shipped dr (see next chapter).
2.1.3 Photocell installation
Install the supplied photocell close to, but before the print-head. This will detect the
product just before it passes the print-head nozzles (Fig. 11)
Coral144 Operator Manual 6
Table des matières
Autres manuels ALE Imprimante
