Alcatel-Lucent OmniSwitch 6250 Manuel utilisateur
OmniSwitch 6250 Series
Getting Started Guide
060302-10, Rev. A
November 2009
Warning. Only personnel knowledgeable in basic electrical and mechanical procedures should install or maintain this
equipment.
The features and specifications described in this guide are subject to change without notice.
Copyright © 2009 by Alcatel-Lucent. All rights reserved. This document may not be reproduced in whole or in part without
the express written permission of Alcatel-Lucent.
Alcatel-Lucent®and the Alcatel-Lucent logo are registered trademarks of Alcatel-Lucent. Xylan®, OmniSwitch®,
OmniStack®, and Alcatel-Lucent OmniVista®are registered trademarks of Alcatel-Lucent.
OmniAccess™, Omni Switch/Router™, PolicyView™, RouterView™, SwitchManager™, VoiceView™, WebView™,
X-Cell™, X-Vision™, and the Xylan logo are trademarks of Alcatel-Lucent.
This OmniSwitch product contains components which may be covered by one or more of the following U.S. Patents:
• U.S. Patent No. 6,339,830
• U.S. Patent No. 6,070,243
• U.S. Patent No. 6,061,368
• U.S. Patent No. 5,394,402
• U.S. Patent No. 6,047,024
• U.S. Patent No. 6,314,106
• U.S. Patent No. 6,542,507
• U.S. Patent No. 6,874,090
Alcatel-Lucent
26801 West Agoura Road
Calabasas, CA 91301
US Customer Support: (800) 995-2696
Internet: service.esd.alcatel-lucent.com
November 2009 iii
OmniSwitch 6250 Series. . . . . . . . . . . . . . . 1
Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Unpacking Instructions . . . . . . . . . . . . . . . . . 3
Items Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Unpacking the Chassis . . . . . . . . . . . . . . . . . . . . . . . 3
Installation Options . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connections and Cabling . . . . . . . . . . . . . . 5
Connecting the Serial Cable . . . . . . . . . . . . . . . . . . . 5
Serial Connection Default Settings . . . . . . . . . . . . . 5
Booting OmniSwitch 6250 Series
Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Booting the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Your First Login Session. . . . . . . . . . . . . . . . 7
Logging in to the Switch . . . . . . . . . . . . . . . . . . . . . 7
Assigning an IP Address to the Switch . . . . . . . . . . 8
Unlocking Session Types . . . . . . . . . . . . . . . . . . . . . 9
Changing the Login Password . . . . . . . . . . . . . . . . 10
Setting the System Time Zone . . . . . . . . . . . . . . . . 11
Setting the Date and Time . . . . . . . . . . . . . . . . . . . 11
Setting Optional System
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Viewing and Saving Changes . . . . . . . . . . . . . . . . . 12
Using WebView. . . . . . . . . . . . . . . . . . . . . . . . . . 13
Browser Compatibility . . . . . . . . . . . . . . . . . . . . . . 13
Logging In to WebView . . . . . . . . . . . . . . . . . . . . . 13
Navigating WebView . . . . . . . . . . . . . . . . . . . . . . . 14
Online Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Additional Information . . . . . . . . . . . . . . . . . . . . . . 16
Troubleshooting WebView . . . . . . . . . . . . . . . . . . . 17
Table of Contents
iv November 2009
November 2009 OmniSwitch 6250 Series 1
OmniSwitch 6250 Series
The Alcatel-Lucent OmniSwitch 6250 Series is a family of
fixed configuration, Gigabit Ethernet, stackable LAN switches
with advanced Layer 2 and basic routing capabilities designed
for both the Enterprise and Metro markets.
Refer to the Product Documentation Card for instructions on
downloading additional hardware and software OmniSwitch
documentation.
2 OmniSwitch 6250 Series November 2009
Related Documentation
The following are the titles and descriptions of all the
OmniSwitch 6250 Series user documentation available for
download. Refer to the included Product Documentation Card
for instructions:
•OmniSwitch 6250 Series Getting Started Guide
Describes the hardware and software procedures for
getting an OmniSwitch 6250 Series switch up and
running.
•OmniSwitch 6250 Series Hardware Users Guide
Complete technical specifications and procedures for
all OmniSwitch 6250 Series hardware, including
chassis, power supplies, fans, combo ports, optional
backup power supplies, etc.
•OmniSwitch CLI Reference Guide
Complete reference to all CLI commands supported on
the OmniSwitch 6250 Series. Includes syntax
definitions, default values, examples, usage
guidelines, and CLI-to-MIB variable mappings.
•OmniSwitch 6250 Switch Management Guide
Includes procedures for readying a switch for
integration into a network. Topics include the software
directory architecture, image rollback protections,
authenticated switch access, managing switch files,
system configuration, using SNMP, and using web
management software (WebView).
•OmniSwitch 6250 Network Configuration Guide
Includes network configuration procedures and
descriptive information on all the major software
features and protocols included in the base software
package. Chapters cover Layer 2 information (Ether-
net and VLAN configuration), Layer 3 information
(static routes), security options (authenticated
VLANs), Quality of Service (QoS), and link
aggregation.
•OmniSwitch Transceivers Guide
Includes information on Small Form Factor Pluggable
(SFPs) and 10 Gbps Small Form Factor Pluggables
(XFPs) transceivers.
November 2009 Unpacking Instructions 3
Items Included
Your OmniSwitch 6250 Series switch order may include the
following items:
•OmniSwitch 6250 Series chassis
•Power supply and power supply tray
•Rack mount flanges with attachment screws (rack
mount flanges may be pre-installed on some orders)
•Power cord (country-specific) and power cord bracket
•Product Documentation Card
•DB9 to RJ-45 serial adapter (Uses RJ-45-to-RJ-45
straight-through cable, not included)
Depending on the items ordered for your specific network
requirements, the following optional items may also be
included:
•SFPs (per order)
•Backup power supply components and cables
(per order)
•Additional mounting or securing hardware
Unpacking the Chassis
To protect your OmniSwitch chassis and hardware compo-
nents from electrostatic discharge (ESD) and physical damage,
read all unpacking recommendations and instructions care-
fully before beginning.
Recommendations
•Unpack your OmniSwitch chassis as close as possible
to the location where it will be installed.
•Depending on your order, Small Form-Factor Plugga-
bles (SFPs) and backup power supply components may
be packaged separately. In order to greatly reduce
exposure to electrostatic discharge (ESD) and physical
damage, do not unpack these items until they are ready
to be installed.
Instructions
1Carefully cut the tape along the seam at the top of the
box containing the chassis.
2Lift the box’s top flaps. Remove any smaller boxes or
pouches that are enclosed and set them aside.
3Lift the chassis out of the packaging.
Unpacking Instructions
4 Unpacking Instructions November 2009
4Carefully remove any foam pads and protective plastic
from the switch chassis as in the example diagram.
5Once all OmniSwitch 6250 Series switches have been
removed from their packaging, continue to “Installation
Options.”
Installation Options
Depending on the model, there are three basic ways in which
the OmniSwitch 6250 Series switches can be installed:
•Rack-mount installation
•Tabletop installation
•Wall-Mount Installation (Model depdenent)
Note: For detailed, step-by-step instructions on install-
ing and mounting OmniSwitch 6250 hardware and
power supplies along with environmental and safety
considerations, please refer to the OmniSwitch 6250
Hardware Users Guide.
November 2009 Connections and Cabling 5
Once your switch is properly set up and all the required hard-
ware components are installed, you should connect all network
and management cables required for your network applica-
tions. Connections may include:
•RJ-45 cable connection to the console port
•Single mode or multimode fiber cables to combo port
SFPs as required by your network
•Ethernet cables to 10/100/1000 Ethernet ports as
required by your network
Connecting the Serial Cable
The console port, located on the chassis front panel, provides a
serial connection to the switch and is required when logging
into the switch for the first time. By default, this RJ-45
connector provides a DTE console connection.
1Locate the console port on the front of
the switch.
2Connect one end of an RJ-45-to-RJ-45
straight-through cable to the console port.
3Connect the other end of an RJ-45-to-RJ-45 straight-
through cable to the supplied DB-9 to RJ-45 adapter.
4Connect the adapter to the PC or terminal with the
default settings below.
Serial Connection Default Settings
The default settings for the serial connection are as follows:
Note. For information on modifying these settings, refer to
the OmniSwitch 6250 Series Hardware Users Guide.
Connections and Cabling
baud rate 9600
parity none
data bits (word size) 8
stop bits 1
6 Booting OmniSwitch 6250 Series Switches November 2009
Booting the Switch
The OmniSwitch 6250 Series switch does not use an on/off
switch. The power cord is the switch’s only connect/discon-
nect device. The power connector socket is located on the
chassis rear panel. For more information, refer to the
OmniSwitch 6250 Series Hardware Users Guide.
To boot the switch, plug the power cord (provided) into the
power connector socket or power brick at the switch’s rear
panel. Next, plug the power cord into an easily-accessible
power source, such as a grounded AC outlet or an Uninterrupt-
ible Power Supply (UPS).
The switch immediately begins the boot process. Allow a few
moments for the switch to boot completely, then verify the
status of all LEDs on the switch’s front panel. A successful
boot displays the following LED states:
If the LED states differ from the states shown in the table,
refer to the OmniSwitch 6250 Series Hardware Users Guide
for more information. Contact Alcatel-Lucent Customer
Support if the unexpected LED state persists.
Booting OmniSwitch 6250
Series Switches
LED States
OK Solid green
PWR Solid green
Autres manuels pour OmniSwitch 6250
6
Table des matières
Autres manuels Alcatel-Lucent Changer
Alcatel-Lucent
Alcatel-Lucent OmniSwitch 6800 Series Manuel de programmation
Alcatel-Lucent
Alcatel-Lucent 7450 ESS-7 Manuel utilisateur
Alcatel-Lucent
Alcatel-Lucent 7210 SAS-D Manuel utilisateur
Alcatel-Lucent
Alcatel-Lucent 7210 SAS D Manuel utilisateur
Alcatel-Lucent
Alcatel-Lucent LambdaUnite 1675 Manuel utilisateur
Alcatel-Lucent
Alcatel-Lucent OmniSwitch 6450 Manuel utilisateur
Alcatel-Lucent
Alcatel-Lucent 1850 TSS-60 Guide de l'utilisateur
Alcatel-Lucent
Alcatel-Lucent 1850 TSS-3 Manuel utilisateur
Alcatel-Lucent
Alcatel-Lucent OmniSwitch 6850-48 Manuel de programmation
Alcatel-Lucent
Alcatel-Lucent 1850 TSS-320 Manuel utilisateur
Alcatel-Lucent
Alcatel-Lucent OmniSwitch 6250 Manuel de programmation
Alcatel-Lucent
Alcatel-Lucent OmniSwitch 6250-M Manuel d'installation
Alcatel-Lucent
Alcatel-Lucent 1850 TSS-3 Manuel utilisateur
Alcatel-Lucent
Alcatel-Lucent OmniSwitch 6350 Manuel d'installation
Alcatel-Lucent
Alcatel-Lucent 7210 SAS E OS Manuel utilisateur
Alcatel-Lucent
Alcatel-Lucent 7210 SAS E OS Manuel utilisateur
Alcatel-Lucent
Alcatel-Lucent OmniSwitch OS6850-P48L Manuel utilisateur
Alcatel-Lucent
Alcatel-Lucent 1671 Service Connect Manuel utilisateur
Alcatel-Lucent
Alcatel-Lucent 7210 SAS-D Feuille d'instructions
Alcatel-Lucent
Alcatel-Lucent 7210 SAS E OS Manuel utilisateur
Manuels Changer populaires d'autres marques
Ruijie
Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation
Altinex
Altinex DA1914SX Manuel utilisateur
MiLAN
MiLAN MIL-SM2401M Manuel utilisateur
RJM
RJM MASTERMIND PBC/6X Manuel utilisateur
Atlas
Atlas MMK-KVM8 Manuel utilisateur
Cabletron Systems
Cabletron Systems GIGAswitch GSR-16 Manuel utilisateur