AirLive WL-5460AP v2 Manuel utilisateur

1 WL5460AP v2 User’s Manual

Wireless Access Point

WL-5460AP v2

User’sManual

2 WL5460AP v2 User’s Manual

FCC Certifications

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

yReorient or relocate the receiving antenna.

yIncrease the separation between the equipment and receiver.

yConnect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

yConsult the dealer or an experienced radio/TV technician for help.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the

user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must accept

any interference received, including interference that may cause undesired operation.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20cm

between the radiator and your body.

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio interference,

in which case the user may be required to take adequate measures.

All trademarks and brand names are the property of their respective proprietors.

Specifications are subject to change without prior notification.

3 WL5460AP v2 User’s Manual

Table of Content

Introduction 4

FEATURES........................................................................................................................................................................5

PARTS NAMES AND FUNCTIONS.......................................................................................................................................6

FACTORY DEFAULT SETTINGS.........................................................................................................................................8

WL-5460AP v2 8

Hardware Connection 9

Check the LEDs: 9

About the Wireless Operation Modes 10

ACCESS POINT MODE ....................................................................................................................................................11

CLIENT MODE (INFRASTRUCTURE)................................................................................................................................12

CLIENT MODE (AD-HOC)...............................................................................................................................................13

BRIDGE MODE...............................................................................................................................................................14

REPEATER MODE (WDS REPEATER /UNIVERSAL REPEATER) ..................................................................................15

WISP MODE (CLIENT ROUTER /WISP+UNIVERSAL REPEATER)..............................................................................16

Configuration 17

LOGIN............................................................................................................................................................................17

MODE............................................................................................................................................................................18

AP Mode setting 19

Security 20

Advanced Settings 26

Access Control 29

Client Mode Settings 30

Bridge Mode Settings 32

Repeater Mode Settings 34

WISP mode Setting 36

STATUS.........................................................................................................................................................................40

System 40

Statistics 42

Active Clients 42

TCP/IP.........................................................................................................................................................................43

OTHER ..........................................................................................................................................................................45

Upgrade Firmware 45

Reboot 45

Save/Reload Settings 45

Password 47

4 WL5460AP v2 User’s Manual

INTRODUCTION

WL-5460APv2 is world's most popular multi-function access point. It features an impressive total of 7

wireless multi-function modes that are not available in normal access point. In addition, the ACK timeout

and RSSI feature makes it suitable for long distance application. From ordinary AP application to Hotspot

and WISP usage, you will find the WL-5460AP is the device you want.

WL-5460APv2 is an IEEE802.11b/g compliant 11 Mbps & 54 Mbps Ethernet Wireless Access Point. The

Wireless Access Point is equipped with two 10/100 M Auto-sensing Ethernet ports for connecting to LAN and

also for cascading to next Wireless Access Point.

WL-5460APv2 provides 64/128bit WEP encryption, WPA and IEEE802.1x which ensures a high level of

security to protect users’ data and privacy. The MAC Address filter prevents the unauthorized MAC

Addresses from accessing your Wireless LAN. Your network security is therefore double assured.

The web-based management utility is provided for easy configuration that your wireless network connection is

ensured to be always solid and hassle free.

5 WL5460AP v2 User’s Manual

Features

1. 2x100Mbps LAN ports for Wireless AP cascade.,2MB flash,16MB SDRAM

2. 18dBm output Power

3. AP ,Bridge,client ,WDS Repeater, Universal Repeater mode.

4. WISP Client Router,WISP+ Universal Repeater mode

5. 802.1x WPA

6. Support data rate automatic fallback.

7. Automatic channel selection.

8. Client access control.

9. Support 802.1x/Radius client with EAP-TLS, TKIP, AES encryption.

10. Support IAPP.

11. Adjustable Tx power, Tx rate, and SSID broadcast.

12. ACK Timeout , Watch dog function.

13. Allow WEP 64/128 bit.

14. Web interface management.

15. Support System event log and statistics.

16. MAC filtering (For wireless only).

Parts Names and Functions

1. Front Panel: (LED Indicators) (5460AP / 5460AP v2)

LED Status

Indicator Color Solid Flashing

1 Power Green Turns solid green when power is

applied to this device.

N/A.

2 Status Red

urns solid red when the device is

booting, after boot successfully,

the light turn off.

Link/Act. Green Turns solid green when connected

and associated to at least a client

station.

Receiving/

Sending data

WEP/WPA Orange Turns solid orange when wireless

security is enabled.

N/A

MAC Ctrl Orange Turns solid orange when MAC

Control is enabled.

N/A

3~6

Wireless

Bridge /

Repeater

Orange Turn solid orange when Bridge or

Repeater is enabled.

N/A

7LAN 1

8 LAN 2 Green Turns solid

green when linked to a

local network.

Receiving/

Sending data

Table 1: LED Indicators

6 WL5460AP v2 User’s Manual

2. Rear Panel: Connection Ports (5460AP / 5460AP v2)

Port/button Functions

A 12V DC Connects the power adapter plug

B LAN1 Connects to Ethernet

C LAN2 Connects to Ethernet

(Factory)

RESET

Press over 3 seconds to reboot this device.

Press for over 10 seconds to restore factory settings.

Performing the Factory Reset will erase all previously

entered device settings.

Table 2: Connection Ports

7 WL5460AP v2 User’s Manual

8 WL5460AP v2 User’s Manual

Factory Default Settings

Setting Wireless Access Point

Device Name WL-5460AP v2

SSID Default value: airlive

Channel 13

WEP Default value: Disabled

IP Address 192.168.100. 252

DHCP Server zIn AP, Client, and Repeater Mode, the default DHCP Server is

OFF default . Please set your PC's IP to the same subnet as the

AP to access the AP

zIn WISP mode, the DHCP server is turned on. Please restart your

PC to renew the IP address.

DHCP Server IP Range 192.168.100.100~192.168.100.200

HARDWARE CONNECTION

Note: Before you starting hardware connection, you are advised to find an appropriate location to place the

Access Point. Usually, the best place for the Access Point is at the center of your wireless network, with line of

straight to all your wireless stations. Also, remember to adjust the antenna; usually the higher the antenna is

placed, the better will be the performance.

1. Connect to your local area network: connect a Ethernet cable to one of the Ethernet port

(LAN1 or LAN2) of this Wireless Access Point, and the other end to a hub, switch, router, or another

wireless access point.

2. Power on the device: connect the included AC power adapter to the Wireless Access Point’s power port

and the other end to a wall outlet.

Check the LEDs:

The Power and LAN # LEDs should be ON. LAN# LED will even blink if there is traffic.

The Link/Act LED will be on in static when associated with a station and blink whenever this AP receives data

packets in the air.

If the Status LED glows after self-test , it means this Wireless Access Point fails on self test. Please ask

your dealer for technical support.

3. Configure your PC: Make sure your local PC(s) has wireless network adapter installed.

9 WL5460AP v2 User’s Manual

10 WL5460AP v2 User’s Manual

ABOUT THE WIRELESS OPERATION MODES

The WL-5460AP v2 device provides all 7 modes of wireless operational applications with :

Access Point,

Bridge,

Client,

WDS Repeater,

Universal Repeater,

WISP (Client Router)

WISP + Universal Repeater

This device is shipped with configuration that is functional right out of the box. If you want to change the

settings in order to perform more advanced configuration or even change the mode of operation, you can use

the web-based utility provided by the manufacturer as described in the following sections.

Autres manuels pour WL-5460AP v2

Table des matières

Autres manuels AirLive Point d'accès sans fil

AirLive

AirLive G.DUO Manuel utilisateur

AirLive

AirLive AC-1200R Manuel utilisateur

AirLive

AirLive WL-5450AP Manuel utilisateur

AirLive

AirLive TOP-12AC Manuel d'installation et d'exploitation

AirLive

AirLive wl-5460apv2 Manuel utilisateur

AirLive

AirLive WT-2000AP Manuel utilisateur

AirLive

AirLive WT-2000AP Manuel utilisateur

AirLive

AirLive WMM-3000AP Manuel utilisateur

AirLive

AirLive WLA-5200AP-G Manuel utilisateur

AirLive

AirLive WHA-5500CPE-NT Manuel utilisateur

AirLive

AirLive WL-5450AP Manuel utilisateur

AirLive

AirLive WL-5460APv2 Guide d'installation

AirLive

AirLive AIRLIVE WL-5430AP Manuel utilisateur

AirLive

AirLive AIRMAX2 Manuel utilisateur

AirLive

AirLive WMU-6000FS Manuel utilisateur

AirLive

AirLive WLA-5200AP Manuel utilisateur

AirLive

AirLive WLA-5000AP Manuel utilisateur

AirLive

AirLive WT-2000AP Manuel utilisateur

AirLive

AirLive WMM-3000AP Manuel utilisateur

AirLive

AirLive WHA-5500CPE Manuel utilisateur

AirLive

AirLive Air Live WL-5470AP Manuel utilisateur

AirLive

AirLive WH-9200AP Manuel utilisateur

AirLive

AirLive WHA-5500CPE Manuel utilisateur

AirLive

AirLive G.DUO Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur