Airlinkplus AME001 Manuel utilisateur

External Modem

User’s Manual

External Modem

User’s Manual

No part of this publication may be reproduced in any form by any means without the prior written permission.

Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective

companies.

May 2003

Contents

CHAPTER 1 BEFORE YOU BEGIN....................................................................................1

1.1 Features.......................................................................................................................................... 1

1.2 Package Contents........................................................................................................................... 1

1.3 Minimum System Requirements ................................................................................................... 1

CHAPTER 2 HARDWARE INSTALLATION ....................................................................3

2.1 Connecting Your Modem.............................................................................................................. 3

2.2 LED Indicators............................................................................................................................... 4

CHAPTER 3 DRIVER INSTALLATION.............................................................................5

3.1 Driver Installation for Windows 95............................................................................................... 5

3.2 Driver Installation for Windows 98............................................................................................... 7

3.3 Driver Installation for Windows Me.............................................................................................. 9

3.4 Driver Installation for Windows 2000......................................................................................... 11

3.5 Driver Installation For Windows XP........................................................................................... 13

3.6 Country Selection ........................................................................................................................ 15

3.7 Verify that Your Modem is Properly Installed............................................................................ 16

3.7.1 For Windows 95/98/Me.................................................................................................................... 16

3.7.2 For Windows 2000/XP ..................................................................................................................... 18

CHAPTER 4 DRIVER UNINSTALLATION.....................................................................21

4.1 Uninstallation from Windows 95/98/Me..................................................................................... 21

4.2 Uninstallation from Windows 2000............................................................................................. 22

4.3 Uninstallation from Windows XP................................................................................................ 24

CHAPTER 5 COMMAND REFERENCE ..........................................................................25

5.1 AT Commands............................................................................................................................. 25

5.1.1 Basic Command Set.......................................................................................................................... 25

5.1.2 Commands Preceded by &................................................................................................................ 28

5.1.3 Commands Preceded by *................................................................................................................. 29

5.1.4 Commands Preceded by \................................................................................................................. 30

5.1.5 Commands Preceded by % .............................................................................................................. 31

5.2 Dial Modifiers............................................................................................................................. 31

5.3 Commands Not Preceded By AT................................................................................................32

5.4 S Register Reference.................................................................................................................... 33

5.4.1 Register Summary............................................................................................................................. 33

5.4.2 Glossary of the S Registers............................................................................................................... 33

CHAPTER 6 MODEM REFERENCE ................................................................................39

6.1 Troubleshooting........................................................................................................................... 39

6.2 Result Codes................................................................................................................................ 39

6.3 Application Examples.................................................................................................................. 40

6.3.1 Dialing a Remote Modem................................................................................................................. 40

6.3.2 Dialing a Stored Number.................................................................................................................. 40

6.3.3 Manual Answer an Incoming Call.................................................................................................... 41

6.3.4 Auto Answer an Incoming Call ........................................................................................................ 41

6.3.5 Voice to Data Switch........................................................................................................................ 41

APPENDICES ........................................................................................................................43

External Modem User's Manual

Appendix A: Caller ID Commands (Optional).................................................................................. 43

Appendix B: Technical Specifications .............................................................................................. 45

Appendix C: Quick Reference........................................................................................................... 46

Appendix D: Glossary ....................................................................................................................... 47

Appendix E: ASCII CODE TABLE.................................................................................................. 49

CHAPTER 1

BEFORE YOU BEGIN

1.1 Features

These Fax/Data/TAM Modems combine the features of a 56000(receive

only)/33600/28800/14400/9600 bps data modem and a 14400/9600 bps FAX modem. Your

new Fax/Data/TAM Modem gives your personal computer the ability to send and receive FAX

messages over the telephone line like a standard FAX machine. Your Fax/Data/TAM Modem

also allows your PC to communicate with other personal computers, terminals or BBS's

(Bulletin Board Systems) through the data modem functions.

When used as a data modem your Fax/Data/TAM Modem uses the standard AT command set

and is fully compatible with ITU-T V.42, V.42bis, V.34, V.32bis, V.32, V.22bis, V.23, V.22,

V.21, MNP 2-5, Bell 103, 212A and V.90. When used as a Fax/Data/TAM Modem it

communicates with all ITU-T Group 3 FAX machines and is compatible with ITU-T V.27ter,

V.29 and V.17. Switching between DATA mode operation and FAX mode operation of your

Fax/Data/TAM Modem is done through its firmware, no hardware settings are required.

The communication software, which should be used, depends on the kind of machine that you

are going to communicate with. If you are going to call a FAX machine then you must use the

Fax software. If the machine that you are going to communicate with is a modem then you

must use a data modem communications software.

Note: This manual is written to be used for several models of Fax/Data/TAM Modems.

Some of the information in this manual may not apply to your Fax/Data/TAM Modem.

All the description in this manual about Caller ID, V.90 and Fax class 1 applies only to

the models which support these functions.

1.2 Package Contents

Before installation, please check the items of your package. The package should include the

following items:

! The External Modem

! Quick Installation

! Installation CD

If any of the above items are missing, please contact your supplier.

1.3 Minimum System Requirements

Before installation, please check that your computer complies with the following requirements:

! Pentium MMX CPU 166 or above (Recommended CPU: Intel Pentium MMX , AMD K6

MMX, Cyrix 6x86 MMX )

! 16MB RAM

! Operating System: Windows 95/ 98/Me/2000/XP

! CD-ROM drive

CHAPTER 2

HARDWARE INSTALLATION

2.1 Connecting Your Modem

Note: For safety, before installing and uninstalling your modem, please make sure the

telephone line is UNPLUGGED from your modem.

Step 1: Power off your computer.

Step 2: Connect one end of the RS-232 serial cable to the modem and the other to your

computer’s serial port.

Note: Connect the male end of the RS-232 cable to the modem’s serial port and the

female end to your computer. Choose suitable 9-pin or 25-pin female connector

according to your computer’s serial port.

Step 3: Plug one end of the RJ-11 phone cord into the LINE jack on the modem, and plug

the other end into your phone jack.

Step 4: For model with PHONE port only. If you want to use a telephone on the modem’s

phone line while the modem is not used , plug the telephone’s cord into the

modem’s PHONE jack.

External Modem User's Manual

Step 5: Plug the AC adapter into the modem’s AC IN jack, and plug the other end into an

electrical outlet.

Step 6: When connection is finished, power on your modem before you power on your PC.

The diagram below illustrates the typical external modem connection:

2.2 LED Indicators

After hardware installation, turn on the modem and then your computer. The PWR, HS, and

MR LEDs should illuminate. The description of the LED indicators on the front panel are

listed below (from left to right) :

MR Modem Ready/ Self-testing On: Power on

Flash: Self-testing/ In diagnostic mode

HS High Speed Speeds On: Operating speed at 24000bps or higher

CD Carrier Detect On: Receiving a data carrier signal from remote modem

OH Off Hook On: Modem off hook

Off: Modem on hook

SD Send Data Flash: Transferring data from the modem

RD Receive Data Flash: Receiving data to the modem

TR Terminal Ready On: Modem is on (unless setup by AT commands)

AA Auto-answer On: Set up to answer incoming calls

PWR Power On: power on

CHAPTER 3

DRIVER INSTALLATION

After hardware installation, turn on your modem and then power on your PC. Follow the

instructions below to install the drivers for the modem.

3.1 Driver Installation for Windows 95

Step 1: Start Windows 95. The Update Device Driver Wizard appears. Insert the provided

Installation CD into your CD-ROM drive. Click Next.

Step 2: Windows will be unable to locate a driver. Click Other Locations.

Step 3: Click Browse to locate the path of the driver: x:\Driver\Win9x (where x is your

CD-ROM drive) and click OK.

Step 4: Windows will find the location of driver; click Finish.

Step 5: If Copying Files window appears, click Browse to locate the path of the driver:

x:\Driver\Win9x (where x is your CD-ROM drive) and click OK.

Step 6: Windows will continue to detect another device. Click Next and then repeat steps 2-

4 to complete driver installation.

External Modem User's Manual

When you are done with driver installation, you will need to specify the country where you

locate upon different telecommunication regulations/ laws. Please proceed to “3.6 Country

Selection” on page 15 for instructions.

Chapter 3 Driver Installation

3.2 Driver Installation for Windows 98

Step 1: Start Windows 98. The Add New Hardware Wizard appears announcing the

detecting of a new hardware. Click Next. Insert the provided Installation CD into

your CD-ROM drive.

Step 2: Select Search for the best driver for your device and click Next.

Step 3: Check Specify a location. Click Browse to locate the path of the driver:

x:\Driver\Win9x (where x is your CD-ROM drive) and click OK. Click Next.

Step 4: When Windows finds the driver file for the device, click Next.

Step 5: If Copying Files window appears, click Browse to locate the driver file and click

OK.

Step 6: Click Finish.

Autres manuels pour AME001

Table des matières

Autres manuels Airlinkplus Modem

Airlinkplus

Airlinkplus AME001 Manuel utilisateur

Manuels Modem populaires d'autres marques

Davicom

Davicom DM562AP Manuel utilisateur

EpiValley

EpiValley TATA indicom SXC-1080 Manuel utilisateur

Zte

Zte WiMAX Manuel utilisateur

Intelimax

Intelimax MA-2060 Manuel utilisateur

SMC Networks

SMC Networks D3CM1604V Manuel d'utilisation et d'entretien

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuel utilisateur

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuel utilisateur

Samsung

Samsung AceLink SAM-335A Manuel utilisateur

Enfora

Enfora Enabler-G Guide de configuration rapide

iRZ

iRZ ATM2-232 Manuel utilisateur

Zhone

Zhone 6310 Manuel utilisateur

Paradyne

Paradyne Hotwire 7976 Manuel utilisateur

US Robotics

US Robotics 3453C Manuel utilisateur

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuel utilisateur

Zte

Zte MF823 Manuel utilisateur

Four-Faith

Four-Faith F1403 Manuel utilisateur

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuel utilisateur

Gemtek

Gemtek WiMAX WIXFBR-103 Manuel utilisateur