Airlink101 ASW408POE Manuel utilisateur

Quick Installation Guide

8-Port 10/100Mbps Switch

with 4-Port PoE

Model# ASW408POE

Ver. 1A

Power Over Ethernet (PoE) is an evolving technology designed to

deliver power and transmit data on an Ethernet cable at the same

time. Modeling after the technology used in telecommunication

systems which supplies power to telephones, PoE powers network

device without the need of AC electrical outlets. By eliminating the

power cords and the power infrastructure, the technology greatly

simplifies the wiring and deployment matters and brings lots of

convenience and benefits in home, office, and industrial

environments.

Features

•8 x 10/100MbpsAuto-negotiation Fast Ethernet RJ 45 with

4-Port PoE function (Port -1 to Port-4)

•Compliant with IEEE802.3af specification

•Support PoE Power Maximum 15.4W per PoE port

•Support PoE Powered Device (PD ) classification identify

•Over Current and Short-circuit Protection

•Each port supports auto MDI/MDIX, no need to use cross-over

cables or an up-link port

•Flow control fully supported:

- Half-duplex: backpressure flow control

- Full-duplex: IEEE802.3x flow control

•Provide non-blocking wire speed reception and transmission

•Embedded 768K bits SDRAM for packet buffering

•1024-entry look-up table in direct mapping mode

•Embedded 16-entry CAM for hash collision mapping

•Optional maximum packet length 1536/1522 Bytes

Purpose

This Quick Installation Guide tells you how to install your Switch and

how to connect it to your Ethernet network.

Terms/Usage

In this manual, the term “Switch” (first letter upper case) refers to your

8-Port 10/100Mbps Switch with 4-Port PoE, and “switch” (first letter

lower case) refers to other Ethernet switches.

1. Introduction

1.1 Package Contents

•1 x ASW408POE

•1 x Switching Power Adapter

•1 x Quick Installation Guide

•4 x Rubber foot for shock cushioning

1.2 Panel

1.2.1 Front Panel

The picture below depicts the front panel of the PoE Switch:

Figure 1-1 Front Panel view of the Switch

•PoE Ports (Port 1~4)

These ports are 802.3af PoE enabled ports, the PoE port will

automatically activate when a compatible terminal is identified. The

PoE switch will distribute power through the Ethernet ports to the

connected PoE device. For devices that are not compatible, the

PoE port will not supply the power to this device. This feature

allows user’s to freely and safely utilize the 802.3af PoE for Power

over Lan devices on their network.

•Ethernet Ports (Port 5~8)

These ports support network speeds of either 10Mbps or 100Mbps,

and can operate in half and full-duplex transfer modes. These ports

also support automatic MDI/MDIX crossover detection, which give

the PoE switch “plug and play” capabilities. Just simply connect

any network cable between the PoE switch and the device and it will

automatically detect the settings of the device and adjust itself

accordingly

•LED Indicators

Comprehensive LED indicators display the status of the switch and

the network (see Section 1.2.3).

1.2.2 Rear Panel

Figure 1-2 Rear Panel view of the Switch

•Power Adapter Connector: DC 48V/0.8A, AC 100~240V,

50~60Hz 1.2A

1.2.3 LED indicators information

The front panel LEDs provide instant status feedback and help monitoring

and troubleshooting when needed.

•Power: Power Indicator

Status

LED Color Solid Blinking Off

Power Green

The Switch is

power-on N/A No power

•Max. PoE: Max. PoE Power Indicator

Status

LED Color Solid Off

Power Green

Power output to PoE

devices has reached

or surpassed the

max. power

When the system is

using less than 38W

•PoE 1~4 LEDs

Status

LED Color Solid Off

PoE 1~4 Green PoE devices

connected

successfully

PoE port failed,

possibly due to:

power shortage, over

the power current or

power adapter out of

DC 44 ~ 57V

•LAN 1~8 LEDs

Status

LED Color Solid Blinking Off

LAN

1~8 Green Connected to

100M network

Transmitting/

Receiving data

on 100M

network

Connected to

10M network or

no device is

connected

1.3 Technical Specifications

Standards

•IEEE 802.3 10BASE–T, IEEE 802.3u 100BASE–TX and IEEE 802.3x

Flow Control, IEEE 802.3af (PoE)

Ports

•8 x 10/100Mbps TXAuto-Negotiation RJ45 Port with 4 PoE ports

Access Method

•CSMA/CD

Transmission Method

•Store and Forward

MAC Address Table

•1K

Built-in Buffer

•768K bits

Data Transfer Rate**

•Ethernet: 10/20Mbps – Half/Full-Duplex

•Fast Ethernet: 100/200Mbps – Half/Full Duplex

PoE Budget

•Up to 15.4W max. per PoE port, 30W total

PoE Power on RJ45

•Power + : ping 3 & ping 6

•Power - : ping 1 & ping 2

Power Consumption

•6.3 watts. (max. no PD device connected)

•36.3 watts (max. with 30W PoE device connected)

Physical and Environmental

•Power Adapter: 48 DC / 0.8A, 100~240V AC, 50~60Hz 1.2A

•Operation Temperature: 0 °C ~ 50°C

•Storage Temperature: -20°C ~ 70°C

•Humidity: 5% ~ 90% RH, non-condensing

The site where you place the switch may greatly affect its performance.

When installing, take the following into your consideration.

2.1 Installation

The setup of the switch can be performed using the following steps:

2. Installing the Switch

•Visually inspect the DC jack and make sure that is fully secured

to the power adapter

•Make sure that there is proper heat dissipation and adequate

ventilation around the Switch. Do not place heavy objects on the

Switch.

2.2 Desktop or Shelf Installation

When installing the Switch on the desktop or shelf, please attach the

rubber feet to the Switch. Peel off the protective paper on the pads and

attach them on the bottom of the Switch (one at each corner).

This section describes how to connect the Switch to your network.

3.1 Connection

The Switch supports 8 10/100Mbps Ethernet ports and Port 1 ~ Port

4 are PoE Enabled ports. These PoE port will automatically activate

when a compatible terminal is identified. The Switch will supply

power through the Ethernet port to the connected PoE powered

device (PD). For legacy devices that are not compatible, the PoE

port will not offer power to this device. This feature allows users to

freely and safely mix legacy and PoE devices on their network.

The Switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet

and it runs both in half and full duplex mode using two pair of

Category 5 cable. These RJ45 ports are Auto-MDI type port. The

Switch can auto negotiate the MDI-II or MDI-X type, so you can

connect any RJ-45 cable regardless if it is a standard or crossover

cable.

3. Connecting the Switch

E-mail: [email protected]

Web Site: www.airlink101.com

*Network conditions and environmental factors as well as network overhead lower actual

data throughput rate. Specifications are subject to change without notice. Photo of product

the stylized AirLink101 logo, specific product designations, and all other words and logos

that are identified as trademarks and/or service marks are, unless noted otherwise, the

trademarks and service marks of AirLink101.All other product or service names are the

property of their respective holders. AirLink101 products are protected under numerous U.S.

and foreign patents and pending applications, mask work rights, and copyrights.

Technical Support

Autres manuels Airlink101 Changer

Airlink101

Airlink101 AKVM-2UDA Manuel utilisateur

Airlink101

Airlink101 AGSW1600 Manuel utilisateur

Airlink101

Airlink101 AKVM-S32 Manuel utilisateur

Airlink101

Airlink101 AKVM-2UDA Manuel utilisateur

Airlink101

Airlink101 AGSW801 Manuel utilisateur

Airlink101

Airlink101 ASW224 Manuel utilisateur

Airlink101

Airlink101 AKVM-2A Manuel utilisateur

Airlink101

Airlink101 AKVM-U42 Manuel utilisateur

Airlink101

Airlink101 AGSW808POE Manuel utilisateur

Airlink101

Airlink101 AKVM-2UA Manuel utilisateur

Airlink101

Airlink101 ASW208 Manuel utilisateur

Airlink101

Airlink101 AGIGA5SW-B Manuel utilisateur

Airlink101

Airlink101 AGSW801 Manuel utilisateur

Airlink101

Airlink101 ASW316V2 Manuel utilisateur

Airlink101

Airlink101 AGSW502 Manuel utilisateur

Airlink101

Airlink101 ASW308P Manuel utilisateur

Airlink101

Airlink101 ASW324V2 Manuel utilisateur

Airlink101

Airlink101 ASW305 Manuel utilisateur

Airlink101

Airlink101 AGSW2400 Manuel utilisateur

Airlink101

Airlink101 DVI-202AU Manuel utilisateur

Airlink101

Airlink101 ASW308 Manuel utilisateur

Airlink101

Airlink101 AKVM-U22 Manuel utilisateur

Airlink101

Airlink101 ASW242G Manuel utilisateur

Airlink101

Airlink101 AKVM-2 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur