Agilent Technologies 5975 Series Manuel

Agilent Technologies

5975 Series

Mass Selective

Detectors

Hardware Installation

2Hardware Installation

Notices

No part of this manual may be reproduced in

any form or by any means (including elec-

tronic storage and retrieval or translation

into a foreign language) without prior agree-

ment and written consent from Agilent

Technologies, Inc. as governed by United

States and international copyright laws.

Manual Part Number

G3170-90002

Edition

First edition, June 2005

Printed in USA

Agilent Technologies, Inc.

5301 Stevens Creek Boulevard

Santa Clara, CA 95052

Safety Notices

CAUTION

A CAUTION notice denotes a haz-

ard. It calls attention to an operat-

ing procedure, practice, or the like

that, if not correctly performed or

adhered to, could result in damage

to the product or loss of important

data. Do not proceed beyond a

CAUTION notice until the indicated

conditions are fully understood and

met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly per-

formed or adhered to, could result

in personal injury or death. Do not

proceed beyond a WARNING

notice until the indicated condi-

tions are fully understood and

met.

Acknowledgements

Microsoft® and Windows® are U.S. regis-

tered trademarks of Microsoft Corporation.

Hardware Installation 3

Contents

1 General Information

Introduction 8

Important Safety Warnings 10

Many internal parts of the MSD carry dangerous voltages 10

Electrostatic discharge is a threat to MSD electronics 10

Many parts are dangerously hot 11

Hydrogen 11

Safety and Regulatory Certifications 13

Information 13

Symbols 14

Electromagnetic compatibility 15

Sound emission declaration for Germany 15

Cleaning 16

Recycling the Product 16

Customer Responsibilities 17

Before You Start 18

Other Documentation 19

This section provides information on how to identify specifically what type of

MSD you are working with as well as how to properly clean and dispose of the

instrument. Also included in this section are the “Important Safety Warnings”

which list critical safety precautions for all users.

8Hardware Installation

1General Information

Introduction

This document provides installation instructions for the Agilent Technologies

5975 Series Mass Selective Detector (MSD). Installation must be performed by

an Agilent Technologies service representative.

The Agilent Technologies 5975 Series Mass Selective Detectors (MSDs) are

turbo pump MSDs.

The 5975 Series MSD system consists of:

•5975 Series MSD

•Optional G3397A High Vacuum Gauge controller (required for CI operation)

•Gas Chromatograph

6890 Series GC, with options for MSD use

7683 Automatic Liquid Sampler (optional)

•Computer and MSD ChemStation software

Refer to your MSD ChemStation documentation for additional information

Table 1 lists possible configurations for the 5975 Series MSD. Figure 1

identifies many of the common parts.

General Information 1

Hardware Installation 9

Table 1 Possible configurations

G3171A G3172A G3174A

High vacuum pump Standard turbo

pump

Performance turbo

pump

Performance turbo

pump

CI No No PCI/NCI

G3397A High vacuum gauge

controller

Recommended Recommended Required

DIP compatible (3rd party) Yes Ye s Yes

Figure 1 5975 Series MSD system

6890 Series

Gas Chromatograph

5975 Series

MSD

Automatic Liquid

Sampler (ALS)

injector

5975 Series MSD LCP

View window

10 Hardware Installation

1General Information

Important Safety Warnings

Before moving on, there are several important safety notices that you should

always keep in mind when using the 5975 Series MSD.

Many internal parts of the MSD carry dangerous voltages

If the MSD is connected to a power source, even if the power switch is off,

potentially dangerous voltages exist on the wiring between the MSD power

cord and the AC power supply, the AC power supply itself, and the wiring from

the AC power supply to the power switch.

With the power switch on, potentially dangerous voltages also exist on:

•All electronics boards in the instrument.

•The internal wires and cables connected to these boards.

•The wires for any heater (oven, detector, inlet, or valve box).

Electrostatic discharge is a threat to MSD electronics

The printed circuit (PC) boards in the MSD can be damaged by electrostatic

discharge. Do not touch any of the boards unless it is absolutely necessary. If

you must handle them, wear a grounded wrist strap and take other antistatic

precautions. Wear a grounded wrist strap any time you must remove the MSD

right side cover.

WARNING All these parts are shielded by covers. With the covers in place, it should be difficult

to accidentally make contact with dangerous voltages. Unless specifically

instructed to, never remove a cover unless the detector, inlet, or oven are turned off.

WARNING If the power cord insulation is frayed or worn, the cord must be replaced. Contact

your Agilent service representative.

Autres manuels pour 5975 Series

Table des matières

Autres manuels Agilent Technologies Capteur de sécurité

Agilent Technologies

Agilent Technologies VS Series Manuel utilisateur

Agilent Technologies

Agilent Technologies InfinityLab 1290 Infinity II Manuel utilisateur

Agilent Technologies

Agilent Technologies 1260 Infinity Manuel utilisateur

Agilent Technologies

Agilent Technologies 1200 Infinity Series Manuel utilisateur

Agilent Technologies

Agilent Technologies NPD Manuel utilisateur

Agilent Technologies

Agilent Technologies 1260 Infinity Manuel utilisateur

Agilent Technologies

Agilent Technologies G6600-90006 Manuel utilisateur

Agilent Technologies

Agilent Technologies G2334A Manuel utilisateur

Agilent Technologies

Agilent Technologies 1260 Infinity Manuel utilisateur

Agilent Technologies

Agilent Technologies 5977C Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 1260 Infinity Manuel utilisateur

Agilent Technologies

Agilent Technologies 1100 Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 8355 Sulfur Manuel utilisateur

Agilent Technologies

Agilent Technologies G3388A Manuel utilisateur

Agilent Technologies

Agilent Technologies 7250 Manuel utilisateur

Agilent Technologies

Agilent Technologies G1563A Manuel utilisateur

Agilent Technologies

Agilent Technologies 1100 Series Manuel utilisateur

Agilent Technologies

Agilent Technologies G8610 Series Guide de référence

Agilent Technologies

Agilent Technologies 1100 Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 85037A Manuel de service

Agilent Technologies

Agilent Technologies 8355 Sulfur Manuel utilisateur

Agilent Technologies

Agilent Technologies 1100 Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 5973N Manuel

Agilent Technologies

Agilent Technologies G3440-68011 Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur