Agilent Technologies E8363BU/CU-068 Manuel d'installation et d'exploitation

Agilent Kit Number: E8364-60106

Agilent Document Number: E8364-90023

Printed in USA June 25, 2010

Supersedes print date: April 2010

Installation Note

Extended Frequency Range (40 or 50 GHz to 67 GHz) Upgrade

Kit

To Add Option 068

Upgrade Kit Order Numbers: E8363BU/CU-068 and E8364BU/CU-068

For E8363B/C and E8364B/C PNA Series Microwave Network

Analyzers

2Installation Note E8364-90023

WARRANTY STATEMENT

THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT TO

BEING CHANGED, WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE MAXIMUM

EXTENT PERMITTED BY APPLICABLE LAW, AGILENT DISCLAIMS ALL WARRANTIES,

EITHER EXPRESS OR IMPLIED WITH REGARD TO THIS MANUAL AND ANY INFORMATION

CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. AGILENT SHALL NOT BE

LIABLE FOR ERRORS OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN

CONNECTION WITH THE FURNISHING, USE, OR PERFORMANCE OF THIS DOCUMENT OR

ANY INFORMATION CONTAINED HEREIN. SHOULD AGILENT AND THE USER HAVE A

SEPARATE WRITTEN AGREEMENT WITH WARRANTY TERMS COVERING THE MATERIAL IN

THIS DOCUMENT THAT CONFLICT WITH THESE TERMS, THE WARRANTY TERMS IN THE

SEPARATE AGREEMENT WILL CONTROL.

DFARS/Restricted Rights Notice

If software is for use in the performance of a U.S. Government prime contract or subcontract,

Software is delivered and licensed as “Commercial computer software” as defined in DFAR

252.227-7014 (June 1995), or as a “commercial item” as defined in FAR 2.101(a) or as

“Restricted computer software” as defined in FAR 52.227-19 (June 1987) or any equivalent

agency regulation or contract clause. Use, duplication or disclosure of Software is subject to

Agilent Technologies’ standard commercial license terms, and non-DOD Departments and

Agencies of the U.S. Government will receive no greater than Restricted Rights as defined in

FAR 52.227-19(c)(1-2) (June 1987). U.S. Government users will receive no greater than

Limited Rights as defined in FAR 52.227-14 (June 1987) or DFAR 252.227-7015 (b)(2)

(November 1995), as applicable in any technical data.

Safety Notes

The following safety notes are used throughout this document. Familiarize yourself with each

of these notes and its meaning before performing any of the procedures in this document.

WARNING Warning denotes a hazard. It calls attention to a procedure which,

if not correctly performed or adhered to, could result in injury or

loss of life. Do not proceed beyond a warning note until the

indicated conditions are fully understood and met.

CAUTION Caution denotes a hazard. It calls attention to a procedure that, if not

correctly performed or adhered to, could result in damage to or destruction

of the instrument. Do not proceed beyond a caution sign until the indicated

conditions are fully understood and met.

Installation Note E8364-90023 3

Description of the Upgrade

This upgrade kit is used to extend the frequency range of the E8363 B/C, or E8364B/C, Option

014 PNA microwave network analyzer from 40 GHz to 67 GHz, or 50 GHz to 67 GHz.

This upgrade applies to a PNA with only Option 014 or Option 014 and 080 in combination.

No other optional hardware combinations can be upgraded with this upgrade kit. If options

016, 081, UNL, or H11 are already installed, special upgrade instructions are required. Stop

here and contact Agilent for these instructions.

Getting Assistance from Agilent

Installing this upgrade kit requires special skills and experience. If you think you may not be

qualified to do the work, or need advice, contact Agilent.

Contacting Agilent

Assistance with test and measurements needs and information on finding a local Agilent

office are available on the Web at:

http://www.agilent.com/find/assist

If you do not have access to the Internet, please contact your Agilent field engineer.

NOTE In any correspondence or telephone conversation, refer to the Agilent product by

its model number and full serial number. With this information, the Agilent

representative can determine whether your product is still within its warranty

period.

4Installation Note E8364-90023

Getting Prepared

To successfully install this upgrade kit, you will need the following:

• A license key - refer to “License Key Redemption” below.

• A PDF copy or a paper copy of the PNA Service Guide - refer to “Downloading the Online

PNA Service Guide” on page 5.

• An ESD-safe work area - refer to “Protecting Your Workspace from Electrostatic

Discharge” on page 5.

• Correct tools - refer to “Tools Required for the Installation” on page 5.

• Enough time - refer to “About Installing the Upgrade Kit” on page 6.

• Test equipment for the post-upgrade adjustments. Refer to “Test Equipment Required for

Post-Upgrade Adjustments” on page 11.

License Key Redemption

NOTE The enclosed Option Entitlement Certificate is a receipt, verifying that you

have purchased a licensed option for the PNA of your choice. You must now

use an Agilent Web page to request a license key for the instrument that

will receive the option.

To enable the option product, you must request a license key from: http://www.agilent.com/

find/softwarelicense. To complete the request, you will need to gather the following

information:

• From the certificate

❏Order number

❏Certificate number

• From your instrument

❏Model number

❏Serial number

❏Host ID

The instrument information is available on the network analyzer – on the analyzer’s Help

menu, click About Network Analyzer.

If you provide an email address, Agilent will promptly email your license key. Otherwise, you

will your receive your license key via postal mail.

Installation Note E8364-90023 5

Downloading the Online PNA Service Guide

To view the online Service Guide for your PNA model number, use the following steps:

1. Go to www.agilent.com

2. In the Search box, enter the model number of the analyzer (Ex: E8363B) and click Search.

3. Click Technical Support > Manuals.

4. Click Service Manual.

5. Click the service guide title to load the PDF file.

6. When the PDF of the Service Guide is displayed, scroll through the Contents section

bookmarks to locate the information needed.

Protecting Your Workspace from Electrostatic Discharge

For information, click on the Chapter 1 PDF bookmark, “Electrostatic Discharge Protection”

in the online Service Guide1.

ESD Equipment Required for the Installation

Tools Required for the Installation

CAUTION Use a 5/16-in torque wrench set to 10 in-lbs on all cable connections except the

front panel and some rear panel cable connectors. Torque these connections to

21 in-lb.

1. See “Downloading the Online PNA Service Guide” on page 5.

Description Agilent Part Number

ESD grounding wrist strap 9300-1367

5-ft grounding cord for wrist strap 9300-0980

2 x 4 ft conductive table mat and 15-ft grounding wire 9300-0797

ESD heel strap (for use with conductive floors) 9300-1308

Description Qty Part Number

T-10 TORX driver - set to 9 in-lbs (1.02 N.m) 1 N/A

T-20 TORX driver - set to 21 in-lbs (2.38 N.m) 1 N/A

5/16-in (8 mm) nutsetter or open end torque wrench - set

to 10 in-lbs (1.13 N.m) 1N/A

5/16-in (8 mm) nutsetter or open end torque wrench - set

to 21 in-lbs (2.38 N.m) 1N/A

1-inch torque wrench - set to 72 in-lbs (8.15 N.m) N/A 1-inch torque wrench

(set to 72 in-lbs)

6Installation Note E8364-90023

About Installing the Upgrade Kit

IMPORTANT Option 068 can only be installed on analyzers with Option 014, as listed

below as “Products affected”. If your analyzer does not have Option 014 (as

listed below), it will be necessary to install the option BEFORE installing

this option (Option 068).

If you need assistance, refer to “Contacting Agilent” on page 3.

Products affected. . . . . . . . . . . . . . . . . . . . . . . . . . E8363B/C and E8364B/C with Option 014,

Configurable Test Set

Installation to be performed by . . . . . . . . . . . . . . Agilent service center or personnel

qualified by Agilent

Estimated installation time . . . . . . . . . . . . . . . . . 3 hours

Estimated adjustment time . . . . . . . . . . . . . . . . . 1 hour

Estimated full instrument calibration time . . . . 4.5 hours

Installation Note E8364-90023 7

Items Included in the Upgrade Kit

Check the contents of your kit against the following list. If any item is missing or damaged,

contact Agilent Technologies. Refer to “Contacting Agilent” on page 3.

Table 1 Contents of Option 068 Upgrade Kit (E8364-60106)

Ref.

Desig. Description Qty Part Number

Installation note (this document) 1 E8364-90023

Entitlement Certificate 1 5964-5145

ROHS addendum 1 9320-6722

Model number nameplate (for 67 GHz analyzer E8361A) 1 E8361-80001

Model number nameplate (for 67 GHz analyzer E8361C) 1 E8361-80006

Lower front panel overlay (Option 014) 1 E8361-80004

A12 Source 20 1 E8361-60002

A17 LOMA 12 1 5087-7247

A18 MA 24 1 5087-7248

A20 LODA 1 5087-7777

A22 Switch 1 5087-7238

A23 SOMA 70, port 1

2 5087-7249

A24 SOMA 70, port 2

A25 Test port 1 coupler

2 5087-7225

A26 Test port 2 coupler

A27 Channel A first converter (mixer)

4 5087-7258

A28 Channel R1 first converter (mixer)

A29 Channel R2 first converter (mixer)

A30 Channel B first converter (mixer)

Mixer bias board 1 E8361-63044

SOMA 70 bracket 2 E8361-00002

Machine screw M3.0 x 10 (for attaching A22 switch) 2 0515-0374

Machine screw M3.0 x 6 (for attaching SOMA 70 brackets) 6 0515-0430

Machine screw M3.0 x 25 (for attaching SOMA 70s to brackets) 4 0515-0667

8Installation Note E8364-90023

1.85 mm female bulkhead connector 12 5065-4673

Nut, hex (for bulkhead connectors) 12 1250-3516

Washer, lock (for bulkhead connectors) 12 1250-3310

Ribbon cable, A23/A24 SOMA 70s to A16 test set motherboard 2 8121-1001

Cable, stranded wire, A22 switch to A16 test set motherboard 1 8121-0990

Cable tie (to secure cable W71) 2 1400-0249

Cable tie mount (to secure cable W71) 2 1400-1551

W2 A21 SOMA 50 to A22 switch 1 E8361-20002

W3 A22 switch to A23 SOMA 70 1 E8361-20003

W4 A22 switch to A24 SOMA 70 1 E8361-20004

W20 A8 fractional-N synthesizer J106 to A17 LOMA 12 J2 1 E8361-20045

W21 A8 fractional-N synthesizer J101 to A17 LOMA 12 J3 1 E8361-20046

W38 A23 SOMA 70 to A16 test set motherboard 1 E8361-60124

W39 A24 SOMA 70 to A16 test set motherboard 1 E8361-60123

W60 Front-panel jumper 6 E8361-20023

W61 RF cable, A23 SOMA 70 to PORT 1 SOURCE OUT 1 E8361-20021

W62 RF cable, A24 SOMA 70 to PORT 2 SOURCE OUT 1 E8361-20022

W63 RF cable, PORT 1 CPLR THRU to A25 test port 1 coupler 1 E8361-20011

W64 RF cable, PORT 2 CPLR THRU to A26 test port 2 coupler 1 E8361-20012

W65 RF cable, A23 SOMA 70 to REFERENCE 1 SOURCE OUT 1 E8361-20015

W66 RF cable, A24 SOMA 70 to REFERENCE 2 SOURCE OUT 1 E8361-20016

W67 RF cable, A25 test port 1 coupler to PORT 1 CPLR ARM 1 E8361-20018

W68 RF cable, A26 test port 2 coupler to PORT 2 CPLR ARM 1 E8361-20018

W69 RF cable, PORT 1 RCVR A IN to A27 channel A mixer 1 E8361-20066

W70 RF cable, REFERENCE 1 RCVR R1 IN to A28 channel R1 mixer 1 E8361-20049

W71 RF cable, REFERENCE 2 RCVR R2 IN to A29 channel R2 mixer 1 E8361-20020

W72 RF cable, PORT 2 RCVR B IN to A30 channel B mixer 1 E8361-20048

Table 1 Contents of Option 068 Upgrade Kit (E8364-60106)

Ref.

Desig. Description Qty Part Number

Installation Note E8364-90023 9

Installation Procedure for the Upgrade Kit

The network analyzer must be in proper working condition prior to installing this option. Any

necessary repairs must be made before proceeding with this installation.

WARNING This installation requires the removal of the analyzer’s protective outer

covers. The analyzer must be powered down and disconnected from the

mains supply before performing this procedure.

Electrostatic Discharge Protection

Protection against electrostatic discharge (ESD) is essential while removing or connecting

cables or assemblies within the network analyzer.

Static electricity can build up on your body and can easily damage sensitive internal circuit

elements when discharged. Static discharges too small to be felt can cause permanent

damage. To prevent damage to the instrument:

•always wear a grounded wrist strap having a 1 MΩresistor in series with it when handling

components and assemblies.

•always use a grounded, conductive table mat while working on the instrument.

•always wear a heel strap when working in an area with a conductive floor. If you are

uncertain about the conductivity of your floor, wear a heel strap.

•always ground yourself before you clean, inspect, or make a connection to a static-sensitive

device or test port. You can, for example, grasp the grounded outer shell of the test port or

cable connector briefly.

Figure 1 shows a typical ESD protection setup using a grounded mat and wrist strap. Refer to

“Tools Required for the Installation” on page 5 for part numbers.

Figure 1 ESD Protection Setup

10 Installation Note E8364-90023

Overview of the Installation Procedure

Step 1. Obtain a Keyword and Verify the Information

Step 2. Remove the Outer and Inner Covers

Step 3. Replace the A12 Source 20

Step 4. Replace the Top Side to Bottom Side Cables

Step 5. Remove the Front Panel Assembly

Step 6. Raise the Receiver Deck

Step 7. Remove the Old Bottom Side Hardware and Cables

Step 8. Install the New Bottom Side Hardware and Cables

Step 9. Lower the Receiver Deck

Step 10. Replace the Front Panel Nameplate and Overlay

Step 11. Reinstall the Front Panel Assembly and Front Panel Jumpers

Step 12. Reinstall the Inner and Outer Covers

Step 13. Enter the New Model Number

Step 14. Perform Post-Upgrade Adjustments

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Agilent Technologies Instrument de mesure

Agilent Technologies

Agilent Technologies MXA N9020A Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies 4291B Manuel utilisateur

Agilent Technologies

Agilent Technologies 4291B Manuel utilisateur

Agilent Technologies

Agilent Technologies 35670A Manuel utilisateur

Agilent Technologies

Agilent Technologies ENA Series Manuel utilisateur

Agilent Technologies

Agilent Technologies Agilent 4396B Manuel utilisateur

Agilent Technologies

Agilent Technologies E5052A Manuel

Agilent Technologies

Agilent Technologies 16753A Manuel utilisateur

Agilent Technologies

Agilent Technologies 4294A Manuel utilisateur

Agilent Technologies

Agilent Technologies 1660A Series Manuel de service

Agilent Technologies

Agilent Technologies Cary 50 Manuel utilisateur

Agilent Technologies

Agilent Technologies E4417A Manuel utilisateur

Agilent Technologies

Agilent Technologies 10400B Series Manuel utilisateur

Agilent Technologies

Agilent Technologies U2722A Manuel utilisateur

Agilent Technologies

Agilent Technologies G7035A Manuel utilisateur

Agilent Technologies

Agilent Technologies L4532A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies E8362B Manuel utilisateur

Agilent Technologies

Agilent Technologies 4294A Manuel du propriétaire

Agilent Technologies

Agilent Technologies E5100A Manuel du propriétaire

Agilent Technologies

Agilent Technologies 8560 E-Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 1670G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies E4440A Guide de démarrage rapide

Agilent Technologies

Agilent Technologies E4418B Manuel utilisateur

Agilent Technologies

Agilent Technologies N9342C Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur