Agilent Technologies Agilent E5810A Manuel utilisateur

Agilent E5810A

LAN/GPIB Gateway for Windows®

Getting Started

Using This Poster. Use Step 1 through Step 4 to install and configure the E5810A

LAN/GPIB Gateway for Windows. If you want to program GPIB and/or RS-232

instruments using your PC or you want to use the Agilent IO Libraries (VISA, VISA

COM, and SICL), also do Step 5 through Step 8.

NOTE

If you have difficulty installing the E5810A, see Troubleshooting Information on the

back of this poster. For additional information on any of the steps on this poster, see

the E5810A LAN/GPIB Gateway for Windows User's Guide.

Check Your Shipment Items. In addition to this poster, your E5810A LAN/GPIB

Gateway shipment should include the items listed. If items are missing or damaged,

contact Agilent Technologies. See E5810A General Information on the back of this

poster for addresses.

• Agilent E5810A LAN/GPIB Gateway for Windows

• E5810A Power Cord

• Agilent Automation-Ready CD with IO Libraries Suite

• E5810A LAN/GPIB Gateway for Windows User's Guide

• E5810A Warranty Statement

• Software License Agreement

Check Your PC/Web Browser. The E5810A LAN/GPIB

Gateway is supported ONLY on Windows XP/Vista/7/8/Server

2008 R2. To communicate with the E5810A from your Web

Browser, you will need Internet Explorer 5.01 or higher (Microsoft Internet Explorer 7

or higher recommended for Vista).

Rack-Mount the E5810A (Optional). As desired, you can mount the E5810A in a

standard EIA rack using the E5810-00100 Rack Mount Kit (or equivalent). The

E5810A is one standard half-rack unit wide and one standard rack unit high. See the

E5810-00100 Rack Mount Kit for instructions.

1 Before You Connect the E5810A

Connect the E5810A to the Network and to Instruments. This figure shows

typical network and instrument connections for the E5810A. Make connections as

required for your application. See the E5810A LAN/GPIB Gateway for Windows

User's Guide for detailed connections.

IMPORTANT

BEFORE making any Enterprise (corporate) network connections, contact your

Information Technology (IT) department for policies concerning user connections, IP

addresses, etc. See Contacting Your IT Department on the back of this poster for

suggested actions.

Apply Power to the E5810A. Plug the E5810A power cord into the E5810A POWER

socket. Then, plug the cord into an AC outlet and observe the E5810A display. After

an initial setup period, the E5810A IP address and hostname (if recognized) should

appear on the display. If the IP address does not appear, see Troubleshooting

Information on the back of this poster.

LAN

GP IB RS232

POWER

GPIB

GPIB Instruments

Typically Hub or

Switch

To Enterprise

Network Instrument

To RS-232

To AC Power

GPIB

LAN

E5810A

2 Install the E5810A

Display the E5810A Welcome Page. To display the E5810A Welcome page, on

your web browser type 'http://<hostname>', where <hostname> is the Hostname of

the E5810A OR type 'http://<IP address>', where <IP address> is the current E5810A

IP address (such as 169.254.58.10) shown on the E5810A display. Then, press Enter.

NOTE

If the Welcome page does not display correctly, you may need to change your web

browser settings. See Configuring Your Web Browser on the back of this poster for

details.

View/Modify Current Configuration (Optional). To view current configuration

settings (and change settings as desired), click the View and Modify Configuration

icon and enter the password (the default password is E5810) to display the Current

Configuration of the E5810 LAN/GPIB Gateway page. Click the Modify

Configuration button to enable you to change settings. After making changes, click

Save and then Reboot E5810 to make changes effective.

Click this icon

to View and

Modify

Configuration

Click this icon

to Find and

Query

Instruments

Current

E5810A

Settings

on Display

3 Configure the E5810A

Verifying Communication from the E5810A. From the E5810A Welcome page,

click the Find & Query Instruments icon and enter the password (default password is

E5810) to display the Instrument page. See the following figure for ways to verify

communication with instruments using the E5810A Instrument page.

Send Commands and Queries to Instruments. To interact with instruments from

the E5810A Instrument page, highlight the instrument to be addressed and type an

instrument command on the Instrument Command line. (See your instrument manual

for instrument commands.) Then, click Send, Receive, or Query as applicable. The

following example shows one way to return a DC voltage measurement from an

instrument.

Click Device Clear, *IDN?, Read

STB, systerr?, or Clear History

Enter command on

Instrument Command line

and then click Send,

Receive, or Query (sends

and receives)

Selected

Instrument

2. Type

Command 3. Click Query

4. Read Response

1. Highlight

Instrument

4 Verify Communication From E5810A

NNNNNNN

The following steps describe installing the Agilent IO Libraries Suite, using default

settings, including:

zChecking for Installed Agilent IO Libraries or Agilent IO Libraries Suite

zInstalling Agilent IO Libraries Suite

ngbbgbInsert the CD.

NOTE

See the Agilent IO Libraries Connectivity Guide on your Automation-Ready CD for a

full description of installation options and installation troubleshooting information. You

MUST have Administrator priviledges to install the Agilent IO Libraries Suite.

Checking for Installed Agilent IO Libraries.

Before you begin installation, check for previously installed Agilent IO Libraries soft-

ware. If a version of the Agilent IO Libraries Suite is installed on your PC, an IO icon

may be displayed on the Windows taskbar notification area.

5 Install Agilent IO Libraries Suite

NOTE

PCs installed with Windows Vista/7/8 MUST upgrade to Agilent IO Libraries v15.0

or above.

1. If the IO icon is displayed, click the icon and click About Agilent IO Control to

display the version. The version must be 15.0 or greater.

2. If the IO icon is not displayed, a version may still be installed. To check this, click

Start >Programs and look for the Agilent IO Libraries or Agilent IO Libraries

Suite program group.

3. If this group is displayed, click Agilent IO Libraries > Utilities > IO Control to

display the IO icon. Then, click the icon and click About Agilent IO Libraries

Control to display the installed version (must be 15.0 or greater).

4. If neither the IO icon nor the Agilent IO Libraries program group is displayed,

Agilent IO Libraries is not installed. Locate the Automation-Ready CD and install

Agilent IO Libraries.

5. If the Agilent IO Libraries Suite version is less than 15.0, install the newer version

included on your Automation-Ready CD to support the E5810A.

6. If your version of the Agilent IO Libraries Suite is at least 15.0, but less than the

version on your Automation-Ready CD, you may want to install the newer version

to take advantage of new features and greater ease of use.

Installing Agilent IO Libraries Suite . First, disconnect any USB instruments, USB/

GPIB converters, and FireWire-VXI interfaces that are connected to your PC. Insert

the Automation-Ready CD into your CD-ROM drive. Wait for a few seconds until the

auto-run window appears. If the auto-run window does not appear automatically, Click

Start > Run then type <x>:autorun\auto.exe where <x> is your CD drive letter. When

the auto-run window appears, follow the directions on that window to install the Agi-

lent IO Libraries Suite. (See Agilent IO Libraries Connectivity Guide on your Automa-

tion-Ready CD for a full description of installation options and installation

troubleshooting information).

NOTE

If possible, always use the current version of the Agilent IO Libraries Suite.

This version supports the newest interfaces and operating systems.

5 Install Agilent IO Libraries Suite (cont.)

Add Remote GPIB Interface. To configure the interface for GPIB instruments, in the

Agilent Connection Expert main screen click Add Interface and select Remote GPIB

interface to display the Remote GPIB Interface dialog box.

1a. Click Find Interfaces...

to locate E5810s on local

subnet.

1b. Or, type hostname or

IP address shown on the

E5810 display.

2. Change this value to the

GPIB SICL Interface Name

displayed on the E5810A

Welcome Page (see Step 3).

3. Test Connection to

verify connectivity and

configuration.

6 Add Remote GPIB Interface

Add Remote Serial Interface. To configure the interface for RS-232 serial

instruments, in the Agilent Connection Expert main screen click Add Interface and

select Remote RS-232 serial interface to display the Remote RS-232 Serial

Interface dialog box.

1a. Click Find Interfaces...

to locate E5810s on local

subnet.

1b. Or, type hostname or

IP address shown on the

E5810 display.

2. Change this value to the

RS-232 SICL Interface

Name displayed on the

E5810A Welcome Page

(see Step 3).

3. Test Connection to

verify connectivity and

configuration.

7 Add Remote RS-232 Serial Interface

Use Interactive IO to Communicate with Instruments. After you have configured

remote GPIB and/or remote serial interfaces, you can use Interactive IO to establish

communication between your PC and your GPIB or RS-232 instruments. To run

Interactive IO for an IEEE-488.2 compliant instrument:

1. Click the instrument's icon in the Connection Expert window.

2. Click Send Commands To This Instrument to display Interactive IO.

3. With the default command, *IDN?, displayed in the text box, click the Send &

Read button.

4. The instrument identification string should appear.

5. Repeat Steps 1 - 4 for the next instrument.

Program Instruments (Optional). After communication has been established, you

can program your GPIB and RS-232 instruments using VISA, VISA COM, or SICL.

See E5810A Documentation/Support on the back of this poster for applicable

documentation.

8 Verify Communication From PC

Autres manuels pour Agilent E5810A

Table des matières

Autres manuels Agilent Technologies Porte

Agilent Technologies

Agilent Technologies Agilent E5810A Manuel utilisateur

Agilent Technologies

Agilent Technologies Agilent E5810A Manuel utilisateur

Agilent Technologies

Agilent Technologies E5810 Manuel d'installation et d'exploitation

Agilent Technologies

Agilent Technologies E5810B Manuel utilisateur

Agilent Technologies

Agilent Technologies Agilent E5810A Manuel utilisateur

Agilent Technologies

Agilent Technologies E5810B Manuel utilisateur

Agilent Technologies

Agilent Technologies 829-0027 Manuel utilisateur

Agilent Technologies

Agilent Technologies E5810 Manuel utilisateur

Agilent Technologies

Agilent Technologies E2050 Manuel de l'opérateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur